Comparison of the instantaneous fuel consumption of vehicles with a different type of propulsion system at constant velocity

• Autorzy: Gołębiewski W. , Stoeck T.

Identyfikatory

DOI

10.5604/12314005.1133182

• Języki publikacji: EN

Abstrakty

EN

The paper presents a comparative analysis of the instantaneous fuel consumption of a FIAT Panda vehicle equipped with a 1.3 JTD MultiJet compression ignition engine with Common Rail fuel system. Different types of propulsion system were taken into consideration (engine positioned front-lengthwise to the direction of travel and rear-wheel drive, engine positioned front-transversely to the direction of travel and front-wheel drive, and all-wheel drive). The method for determining the instantaneous fuel consumption was based on an experimental part where the load characteristics were established (relationship between specific fuel consumption and engine torque). It was carried out for the steady states of these parameters corresponding to specific traffic conditions that represent the resistance to motion, i.e. rolling resistance and air resistance. Technical and operating characteristics of a vehicle and its design features, such as maximum weight, transmission system ratios, dynamic wheel radius, drag coefficient, width and height, and efficiency of propulsion system, had a significant impact on their individual contribution. The efficiency of transmission was adopted from a simulation for different types of propulsion system. It was important in determination of the value of instantaneous fuel consumption for constant vehicle velocities used in the UDC test (Urban Driving Cycle – subtest of the EUDC cycle). The lowest fuel consumption for a given speed of a car occurred for the front-wheel drive transmission system, whereas the highest for the all-wheel drive system (4x4).

Słowa kluczowe

EN

instantaneous fuel consumption; UDC cycle; passenger car; propulsion system; constant velocity

• Wydawca: Łukasiewicz Research Network - Institute of Aviation ; European Science Society of Powertrain and Transport KONES Poland ; Wydawnictwo Instytutu Technicznego Wojsk Lotniczych
• Czasopismo: Journal of KONES
• Rocznik: 2014
• Tom: Vol. 21, No. 3
• Strony: 113--120
• Opis fizyczny: Bibliogr. 12 poz., rys.

Twórcy

autor

Gołębiewski W.

• West Pomeranian University of Technology, Department of Automotive Vehicles Operation Piastów Av. 19, 70-310 Szczecin, Poland tel.: [phone]

autor

Stoeck T.

• West Pomeranian University of Technology, Department of Automotive Vehicles Operation Piastów Av. 19, 70-310 Szczecin, Poland tel.: [phone]

Bibliografia

• [1] ADAC, Allgemeiner Deutscher Automobil-Club, EcoTest - testing and assessment protocol release 2.1,2009.
• [2] Akcelik, R., Smit, R. and Besley, M., Calibrating fuel consumption and emission models for modern vehicles, IPENZ Transportation Group Conference, Rotorua, New Zealand 2012.
• [3] Dębicki, M., The theory of motorcar. The theory of drive, WNT, Poland 1976.
• [4] European Commission Directive 1999/100/EC of 15 December 1999 adapting to technical progress Council Directive 80/1268/EEC relating to the carbon dioxide emissions and the fuel consumption of motor vehicles.
• [5] Gao, Y., Checkel, M. D., Experimental measurement of on-road CO2 emission and fuel
• consumption functions, SAE World Congress & Exhibition, Session, Life Cycle Analysis/Energy or Emissions Modelling, SAE, USA 2007.
• [6] Kropiwnicki, J., Evaluation of the reference fuel consumption and CO2 emission of vehicle with using of the map of operating conditions for selected agglomeration. Journal of KONES Powertrain and Transport, Vol. 17, No. 3, pp. 239-246, 2010.
• [7] Lisowski, M., An analysis of fuel consumption by a lorry with the compression ignition dynamic charged engine, TEKA Commission of Motorization and Energetics in Agriculture, Polish Academy of Sciences Branch in Lublin, Vol. VIIIA, pp. 118-125,2008.
• [8] Micknass, W., Popiol, R., Sprenger, A., Sprzęgła, skrzynki biegów, wały i półosie napędowe, WKŁ, Warszawa 2004.
• [9] Mock, P., German, J., Bandivadekar, A., Riemersma, i.. Discrepancies between type-approval and real-world fuel-consumption and CO2 values. The International Council of Clean Transportation, Washington - Berlin - San Francisco 2012.
• [10] PN-ISO 15550 standard. Combustion piston engines. Determination and method of engine power measurement. General requirements, PKN, Poland 2009.
• [11] Prochowski, L., The mechanics of motion, WKŁ, Poland 2007.
• [12] Zembowicz, J., FIAT Panda, WKŁ, Poland.