Serial control of CNC machines

• Autorzy: Kowalski P. , Smyk R.

Identyfikatory

DOI

10.21008/j.1508-4248.2016.0022

• Języki publikacji: EN

Abstrakty

EN

In this paper a new method of the serial control of CNC machines is proposed. Actuators are controlled locally and the role of the central computer is limited to sending commands to the controller instead of sending it directly to actuators. It has been achieved with the use of the serial protocol with the use of the USB port. The taken approach leads to more reliable operation because commands are buffered and no synchronization between command stream and actuators operation is needed.

Słowa kluczowe

EN

CNC machine; serial control; stepper motors; serial communication

• Wydawca: Wydawnictwo Politechniki Poznańskiej
• Czasopismo: Computer Applications in Electrical Engineering
• Rocznik: 2016
• Tom: Vol. 14
• Strony: 245--255
• Opis fizyczny: Bibliogr. 16 poz., rys., tab.

Twórcy

autor

Kowalski P.

• Gdańsk University of Technology

autor

Smyk R.

• Gdańsk University of Technology

Bibliografia

• [1] Yusof Y., Latif K., Development of new open soft–CNC system International Conference Computer Communications and Control Technology (I4CT) 2015, pp. 82–86.
• [2] Le N.Q. Jeon J.W., An open–loop stepper motor driver based on FPGA International Conference Control Automation and Systems. ICCAS 2007, pp. 1322–1326.
• [3] Allegro Microsystems datasheet – Microstepping Driver A4988 2011.
• [4] STMicroelectronics L297 Datasheet 2001.
• [5] Texas Instruments DRV8825 Stepper Motor Controller IC Datasheet 2014.
• [6] Texas Instruments DRV8846 – Dual H–Bridge Stepper Motor Driver IC Datasheet 2014.
• [7] Rocha P. a. S., Diogne de Silva e Souza R., Tostes L., Emília M., Prototype CNC machine design, 2010 9th IEEE/IAS International Conference, Industry Applications (INDUSCON), 2010, pp. 1–5.
• [8] ArtSoft, Mach3 CNC Controller Software Installation and Configuration, 2008.
• [9] Compaq Hewlett–Packard, Intel, Lucent, Microsoft, NEC, Philips, Universal Serial Bus, Specification Revision 2.0, 2000.
• [10] Kramer T.R., Proctor F.M., Messina E., The NIST RS274/NGC Interpreter– Version 3, ISD of National Institute of Standards and Technology, Gaithersburg, 2000.
• [11] Fabiański B., Sterownik drukarki trójwymiarowej z obsługą nowych technologii, Poznań University of Technology, Academic Journals, Poznań 2014, No. 80, pp.253–260.
• [12] PI (Physik Instrumente) LP, Piezo Motor Catalog; Piezo Positioners, Ultrasonic Motors, Piezo Stepping Motors, Stick Slip Motors, 2013.
• [13] Douglas A. Kerr, The Canon USM (Ultrasonic Motor) Autofocus Drive System, 2011.
• [14] Hewlett–Packard Development Company, Bluetooth wireless technology basics, 2004.
• [15] STMicroelectronics, STM32F100x4 STM32F100x6 STM32F100x8 STM32 F100xB – Low & medium–density value line, advanced ARM®–based 32–bit MCU with 16 to 128 KB Flash, 12 timers, ADC, DAC & 8 comm interfaces, 2015.
• [16] Texas Instruments, DRV8835 – Dual low voltage h–bridge ic, 2014.

Uwagi

Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę (zadania 2017).