Diagnostics of Synchronous Motor Based on Analysis of Acoustic Signals with the use of Line Spectral Frequencies and K-nearest Neighbor Classifier

• Autorzy: Glowacz A.

Identyfikatory

DOI

10.2478/aoa-2014-0022

• Języki publikacji: EN

Abstrakty

EN

In industrial processes electrical motors are serviced after a specific number of hours, even if there is a need for service. This led to the development of early fault diagnostic methods. Paper presents early fault diagnostic method of synchronous motor. This method uses acoustic signals generated by synchronous motor. Plan of study of acoustic signal of synchronous motor was proposed. Two conditions of synchronous motor were analyzed. Studies were carried out for methods of data processing: Line Spectral Frequencies and K-Nearest Neighbor classifier with Minkowski distance. Condition monitoring is useful to protect electric motors and mining equipment. In the future, these studies can be used in other electrical devices.

Słowa kluczowe

EN

acoustic signal; pattern analysis; synchronous motor; diagnostics

• Wydawca: Instytut Podstawowych Problemów Techniki PAN ; Komitet Akustyki PAN ; Polskie Towarzystwo Akustyczne
• Czasopismo: Archives of Acoustics
• Rocznik: 2014
• Tom: Vol. 39, No. 2
• Strony: 189--194
• Opis fizyczny: Bibliogr. 59 poz., wykr.

Twórcy

autor

Glowacz A.

• AGH University of Science and Technology al. A. Mickiewicza 30, 30-059 Kraków, Poland

Bibliografia

• 1. BIENIAS J., JAKUBCZAK P., MAJERSKI K., OSTA- PIUK M., SUROWSKA B. (2013), Methods of ultrasonic testing, as an effective way of estimating durability and diagnosing operational capability of composite laminates used in aerospace industry, Eksploatacja i Niezawodność - Maintenance and Reliability, 15, 3, 284-289.
• 2. BOGUCKA J. (2014), Influence of Temperature of Accumulative Roll Bonding on the Microstructure and Mechanical Properties of AA5251 Aluminum. Alloy, Archives of Metallurgy and Materials, 59, 1, 127-131.
• 3. BOZKURT E., ERZIN E., ERDEM C.E., ERDEM A.T. (2010), Use of Line Spectral Frequencies for emotion recognition from, speech., International Conference on Pattern Recognition (ICPR), Istanbul, Turkey.
• 4. CZMOCHOWSKI J., MOCZKO P., ODYJAS P., PIETRU- SIAK D. (2014), Tests of rotary machines vibrations in. steady and unsteady states on. the basis of large diameter centrifugal fans, Eksploatacja i Niezawodność - Maintenance and Reliability, 16, 2, 211-216.
• 5. Duan RX., Zhou HL. (2014), Diagnosis strategy for micro-computer controlled straight electro-pneumatic braking system, using fuzzy set and dynamic fault tree, Eksploatacja i Niezawodność - Maintenance and Reliability, 16, 2, 217-223.
• 6. DUDA S. (2013), Numerical modeling and simulating the dynamic interactions within, the drive system, of electric rail vehicles, Eksploatacja i Niezawodność - Maintenance and Reliability, 15, 4, 343-348.
• 7. DUDZIKOWSKI I., ClURYS M. (2010), Analysis of operation of a car starter with. BLDC motor, Przegląd Elektrotechniczny, 86, 4, 166-169.
• 8. GIRTLER J, SLEZAK M. (2013), Four-state stochastic model of changes in. the reliability states of a motor vehicle, Eksploatacja i Niezawodność - Maintenance and Reliability, 15, 2, 156-160.
• 9. GŁOWACZ A., GŁOWACZ Z. (2012), Diagnostics of DC machine based on. analysis of acoustic signals with, application of MFCC and classifier based on. words, Archives of Metallurgy and Materials, 57, 1, 179-183.
• 10. GŁOWACZ A., GŁOWACZ A., KOROHODA P. (2014a), Recognition of Monochrome Th.erm.al Images of Synchronous Motor with, the Application of Binarization and Nearest Mean. Classifier, Archives of Metallurgy and Materials, 59, 1, 31-34.
• 11. GŁOWACZ A., GŁOWACZ A., GŁOWACZ Z. (2014b), Recognition of monochrome thermal images of synchronous motor with, the application of quadtree decom,- position. and backpropagation. neural network, Eksploatacja i Niezawodność - Maintenance and Reliability, 16, 92-96.
• 12. GŁOWACZ Z., GŁOWACZ A. (2007), Simulation language for analysis of discrete-continuous electrical systems (SESL2), Proceedings of the 26th IASTED International Conference on Modelling, Identification, and Control, Innsbruck, Austria, 94-99.
• 13. GŁOWACZ W. (2013), Diagnostics of Induction, motor based on. Spectral Analysis of Stator Current with. Application of Backpropagation. Neural Network, Archives of Metallurgy and Materials, 58, 2, 559-562.
• 14. GŁOWACZ Z., KOZIK J. (2012), Feature selection of the armature winding broken coils in synchronous motor using genetic algorithm and, Mahalanobis distance, Archives of Metallurgy and Materials, 57, 3, 829-835.
• 15. GŁOWACZ Z., KOZIK J. (2013), Detection of synchronous motor inter-turn faults based on spectral analysis of park’s vector, Archives of Metallurgy and Materials, 58, 1, 19-23.
• 16. GŁOWACZ Z., ZDROJEWSKI A. (2009), Diagnostics of commutator DC motor using spectral analysis method, Przegląd Elektrotechniczny, 85, 1, 147-150.
• 17. GŁUCHOWSKI WJ., RDZAWSKI ZM., STOBRAWA JP., MARSZOWSKI KJ. (2014), Micro structure and Properties of Cu-Nb Wire Composites, Archives of Metallurgy and Materials, 59, 1, 35-40.
• 18. GOGOLA D., KRAFCIK A., STRBAK O., FROLLO I. , Magnetic Resonance Imaging of Surgical Implants Made from Weak Magnetic Materials, Measurement Science Review, 13, 4, 165-168.
• 19. GOLANSKI G., SŁANIA J. (2013), Effect of different heat treatments on microstructure and, mechanical properties of the martensitic GX12CrMoVNbN9-l cast steel, Archives of Metallurgy and Materials, 58, 1, 25-30.
• 20. GRONOSTAJSKI Z., HAWRYLUK M., KRAWCZYK J., MARCINIAK M. (2013), Numerical modelling of the thermal fatigue of steel WCLV used for hot forging dies, Eksploatacja i Niezawodność - Maintenance and Reliability, 15, 2, 129-133.
• 21. GWOZDZIEWICZ M., ZAWILAK J. (2011), Influence of the rotor construction on the single-phase line start permanent magnet synchronous motor performances, Przegląd Elektrotechniczny, 87, 11, 135-138.
• 22. HACHAJ T., OCIELĄ MR. (2013), Application of neural networks in detection of abnormal brain perfusion regions, Neurocomputing, 122 (Special Issue), 33-42.
• 23. HACHAJ T., OGIELA MR. (2011), CAD system, for automatic analysis of CT perfusion, maps, Opto- Electronics Review, 19, 1, 95-103.
• 24. ITAKURA F. (1975), Line spectrum representation of linear predictive coefficients of speech signals, Journal of the Acoustical Society of America, 57, SI, p. S35.
• 25. JAKLINSKI P. (2013), Analysis of the dual control system operation during failure conditions, Eksploatacja i Niezawodność - Maintenance and Reliability, 15, 3, 266-272.
• 26. JAWOREK J., AUGUSTYNIAK P. (2011), A cardiac telerehabilitation application for mobile devices, IEEE Conference on Computing in Cardiology, Hangzhou, China, 241-244.
• 27. KANTOCH E., SMOLEN M., AUGUSTYNIAK P., KOWALSKI P. (2011), Wireless Body Area Network System based, on ECG and, Accelerometer Pattern, IEEE Conference on Computing in Cardiology, Hangzhou, China, 245-248.
• 28. KANTOCH E., AUGUSTYNIAK P. (2012), Body Area Network System Based on ECG, GPS and, Movement Signals, Journal of Medical Imaging and Health Informatics, 2, 1, 76-79.
• 29. KNAP M., FALKUS J., ROZMAN A., KONOPKA K., LAMUT J. (2014), The Prediction, of Hardenability using Neural Networks, Archives of Metallurgy and Materials, 59, 1, 133-136.
• 30. KOZLOWSKI M. (2009), Wavelet analysis of current applied to detect traction adhesion loss condition of a railway vehicle, Przeglad Elektrotechniczny, 85, 11, 51-54.
• 31. KULCZYK M., PRZYBYSZ S., SKIBA J., PACHLA W. , Severe Plastic Deformation Induced, in Al, Al- Si, Ag and, Cu by Hydrostatic Extrusion, Archives of Metallurgy and Materials, 59, 1, 59-64.
• 32. KULESZA G., PANEK P., ZIEBA P. (2013), Silicon solar cells efficiency improvement by the wet chemical texturization in the HF/HN03/diluent solution, Archives of Metallurgy and Materials, 58, 1, 291-295.
• 33. LIN DF., CHEN PH., WILLIAMS M. (2013), Measurement and, Analysis of Current Signals for Gearbox Fault Recognition of Wind Turbine, Measurement Science Review, 13, 2, 89-93.
• 34. MADEJ M. (2013), Phase Reactions During Sintering of M3/2 Based Composites with, WC Additions, Archives of Metallurgy and Materials, 58, 3, 703-708.
• 35. MAMALA A., SciEZOR W. (2014), Evaluation of the Effect of Selected Alloying Elements on the Mechanical and Electrical Aluminium Properties, Archives of Metallurgy and Materials, 59, 1, 413-417.
• 36. MEO A., PROFUMO L., ROSSI A., LANZETTA M. (2013), Optimum Dataset Size and, Search Space for Minimum Zone Roundness Evaluation by Genetic Algorithm, Measurement Science Review, 13, 3, 100-107.
• 37. MICHALAK M., SIKORA M., SOBCZYK J. (2013), Analysis of the longwall conveyor chain based on a harmonic analysis. Eksploatacja i Niezawodnosc - Maintenance and Reliability, 15, 4, 332-336.
• 38. MlKULIK J., Zajdel M. (2009), Automatic risk control based on FSA methodology adaptation for safety assessment in intelligent buildings, International Journal of Applied Mathematics and Computer Science, 19, 317-326.
• 39. MlNG LEUNG K. (2007), k-Nearest Neighbor algorithm for classification, Polytechnic University Department of Computer Science/Finance and Risk Engineering.
• 40. MORRIS R.W., CLEMENTS M.A. (2002), Modification of formants in the line spectrum domain, IEEE Signal Processing Letters, 9, 1, 19-21.
• 41. MusiAL D. (2013), Numerical Analysis of the Process of heating of a bed of steel bars, Archives of Metallurgy and Materials, 58, 1, 63-66.
• 42. OGIELA MR., TADEUSIEWICZ R., TRZUPEK M. (2007), Graph-based semantic description in medical knowledge representation and, 3D coronary vessels recognition, Ubiquitous Intelligence and Computing, Proceedings, Book Series: Lecture notes in computer science, 4611, 1079-1088.
• 43. OLEKSY A., SZYMAŃSKI Z. (2010), Modern methods control and, diagnostics of hoisting-machines with, application of artificial intelligence methods, Archives of Mining Sciences, 55, 1, 217-231.
• 44. ORLEWSKI W., SIWEK A. (2010), Hydroelectric power- plant using dump industrial water, Rynek Energii, 6, 87-91.
• 45. Roj J. (2013), Neural Network Based Real-time Correction of Transducer Dynamic Errors, Measurement Science Review, 13, 6, 286-291.
• 46. ROJEK I., STUDZIŃSKI J. (2014), Comparison of different types of neuronal nets for failures location within water-supply networks, Eksploatacja i Niezawodność - Maintenance and Reliability, 16, 1, 42-47.
• 47. SlN M. L., SOONG W. L., ERTUGRUL N. (2003), Induction machine on-line condition monitoring and, fault diagnosis - A survey, in AUPEC, Christchurch, New Zealand.
• 48. SKOWRONEK K., WOZNIAK A. (2013), FFT-PCA-LDA classifier in AC Generator diagnostics, Eksploatacja i Niezawodność - Maintenance and Reliability, 15, 2, 140-146.
• 49. SMALCERZ A. (2013), Aspects of application of industrial robots in metallurgical processes, Archives of Metallurgy and Materials, 58, 1, 203-209.
• 50. SMOLEN M., KANTOCH E., AUGUSTYNIAK P., KOWALSKI P. (2012), Wearable Patient Home Monitoring Based on EGG and, ACC Sensors, 5th European Conference of the International Federation for Medical and Biological Engineering, IFMBE Proceedings, 37, 941- 944.
• 51. STUBNA I., SIN P., TRNIK A., VOZAR L. (2014), Measuring the Flexural Strength of Ceramics at Elevated Temperatures - An Uncertainty Analysis, Measurement Science Review, 14, 1, 35-40.
• 52. Su C., Fu YQ. (2014), Reliability assessment for wind, turbines considering the influence of wind speed using bayesian network, Eksploatacja i Niezawodność - Maintenance and Reliability, 16, 1, 1-8.
• 53. SZYSZKIEWICZ K., DZIEMBAJ P., FILIPEK R. (2013), Heat transfer and, inverse problems; selected, cases in ID and, 3D geometries, Archives of Metallurgy and Materials, 58, 1, 9-18.
• 54. Tasinkevych Y., Trots I., Nowicki A., Lewandowski M. (2012), Optimization of the multi-element synthetic transmit aperture method for medical ultrasound imaging applications, Archives of Acoustics, 37, 1, 47-55.
• 55. Tomczak J., Pater Z., Bulzak T. (2013), Effect of technological parameters on the rotary compression, process, Eksploatacja i Niezawodność - Maintenance and Reliability, 15, 3, 279-283.
• 56. Tu YQ., YANG HY., ZHANG HT., LIU XY. (2014), CMF Signal Processing Method Based on Feedback Corrected ANF and, Hilbert Transform a tion, Measurement Science Review, 14, 1, 41-47.
• 57. Uygur I., Cicek A., Toklu E., Kara R., S ARID EMIR S. (2014), Fatigue Life Predictions of Metal Matrix Composites Using Artificial Neural Networks, Archives of Metallurgy and Materials, 59, 1, 97-103.
• 58. VALIS D., PIETRUCHA-URBANIK K. (2014), Utilization of diffusion processes and, fuzzy logic for vulnerability assessment, Eksploatacja i Niezawodność - Maintenance and Reliability, 16, 1, 48-55.
• 59. ZUBER N., BAJRIC R., SOSTAKOV R. (2014), Gearbox faults identification using vibration signal analysis and, artificial intelligence methods, Eksploatacja i Niezawodność - Maintenance and Reliability, 16, 1, 61-65.