Structural Characterization and Properties of Al/Fe Multi-Layer Composites Produced by Hot Pressing

• Autorzy: Kowalski Wojciech , Paul Henryk , Mania Izabela , Petrzak Paweł , Czaja Paweł , Chulist Robert , Góral Anna , Szlezynger Maciej

Identyfikatory

DOI

10.24425/amm.2023.141487

• Języki publikacji: EN

Abstrakty

EN

This study aimed to develop Fe/Al multilayered metallic/intermetallic composites produced by hot pressing under an air atmosphere. Analyses were carried out on the composite plates made up of alternatively situated sheets of AA1050 aluminum alloy and DN04 low carbon steel, which were annealed at 903 K for 2, 5, and 10 h. Annealing was performed to obtain reaction layers of distinct thickness. The samples were examined using X-Ray diffraction and scanning and transmission electron microscope equipped with an energy-dispersive X-Ray spectrometer. To correlate the structural changes with mechanical properties, microhardness measurements in near-the-interface layers were performed. All the reaction layers grew with parabolic kinetics with η-Al₅Fe₂ intermetallic phase as the dominant component. After annealing for 5 and 10 hours, a thin sublayer of θ-Al₁₃Fe₄ phase was also detected.

Słowa kluczowe

EN

Fe/Al multilayered composite; intermetallic phase; electron microscopy; microhardness test

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2023
• Tom: Vol. 68, iss. 1
• Strony: 137--144
• Opis fizyczny: Bibliogr. 24 poz., fot., rys., tab., wykr.

Twórcy

autor

Kowalski Wojciech

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str., 30-059 Krakow, Poland

• https://orcid.org/0000-0003-1598-8149

autor

Paul Henryk

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str., 30-059 Krakow, Poland

• https://orcid.org/0000-0003-4107-982X

autor

Mania Izabela

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str., 30-059 Krakow, Poland

• https://orcid.org/0000-0002-9087-2114

autor

Petrzak Paweł

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str., 30-059 Krakow, Poland

• https://orcid.org/0000-0001-8981-1480

autor

Czaja Paweł

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str., 30-059 Krakow, Poland

• https://orcid.org/0000-0001-5011-9323

autor

Chulist Robert

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str., 30-059 Krakow, Poland

• https://orcid.org/0000-0001-6680-9636

autor

Góral Anna

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str., 30-059 Krakow, Poland

• https://orcid.org/0000-0001-7823-0496

autor

Szlezynger Maciej

• Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str., 30-059 Krakow, Poland

• https://orcid.org/0000-0002-6230-9340

Bibliografia

• [1] M. Krasnowski, T. Kulik, Nanocrystalline and amorphous Al-Fe alloys containing 60-85% of Al synthesised by mechanical alloying and phase transformations induced by heating of milling products, Mater Chem. Phys. 116, 631-637 (2009). DOI: https://doi.org/10.1016/j.matchemphys.2009.05.003
• [2] M. Krasnowski, T. Kulik, Nanocrystalline Al-Fe intermetallics - lightweightalloys with high hardness, Intermetallics 18, 47-50 (2010). DOI: https://doi.org/10.1016/j.intermet.2009.06.006
• [3] X. Li, A. Scherf, M. Heilmaier, F. Stein, The Al-rich part of the Fe-Al phase diagram, J. Phase Equlib. Diff. 37, 162-173 (2016). DOI: https://doi.org/10.1007/s11669-015-0446-7
• [4] G.H.S.F.L. Carvalho, I. Galvão, R. Mendes, R.M. Leal, A. Loureiro, Explosive welding of aluminium to stainless steel, J. Mater. Process. Tech. 262, 340-349 (2018). DOI: https://doi.org/10.1016/j.jmatprotec.2018.06.042
• [5] G.H.S.F.L. Carvalho, I. Galvão, R. Mendes, R.M. Leal, A. Loureiro, Formation of intermetallic structures at the interface of steel-to-aluminium explosive welds, Mater. Charact. 142, 432-442 (2018). DOI: https://doi.org/10.1016/j.matchar.2018.06.005
• [6] Z. Guo, M. Liu, Z. Bian, M. Liu, J. Li, An Al-7Si alloy/cast iron bimetallic composite with super-high shear strength, J. Mater. Res. Tech. 8 (3), 3126-3136 (2019). DOI: https://doi.org/10.1016/j.jmrt.2017.06.014
• [7] H. Paul, Ł. Maj, M. Prażmowski, A. Gałka, M. Miszczyk, P. Petrzak, Microstructure and mechanical properties of multilayered Al/Ti composites produced by explosive welding, Procedia Manufacturing 15, 1391-1398 (2018). DOI: https://doi.org/10.1016/j.promfg.2018.07.343
• [8] D.M. Fronczek, R. Chulist, Z. Szulc, J. Wojewoda-Budka, Growth kinetics of TiAl3 phase in annealed Al/Ti/Al explosively welded clads, Mater. Lett. 198, 160-163 (2017). DOI: https://doi.org/10.1016/j.matlet.2017.04.025
• [9] Y. Liu, X. Chong, Y. Jiang, R. Zhou, J. Feng, Mechanical properties and electronic structures of Fe-Al intermetallic, Physica B 506, 1-11 (2017). DOI: http://dx.doi.org/10.1016/j.physb.2016.10.032
• [10] M.Z. Khalid, J. Friis, P.H. Ninive, K. Marthinsen, A. Strandlie, Ab-initio study of atomic structure and mechanical behaviour of Al/Fe intermetallic interfaces, Comput. Mater. Sci. 174, 109481 (2020). DOI: https://doi.org/10.1016/j.commatsci.2019.109481
• [11] N.L. Okamoto, J. Okumura, M. Higashi, H. Inui, Crystal structure of η’-Fe3Al8; low-temperature phase of η-Fe2Al5 accompanied by anordered arrangement of Al atoms of full occupancy in the c-axis chain sites, Acta Mater. 129, 290-299 (2017). DOI: http://dx.doi.org/10.1016/j.actamat.2017.02.060
• [12] H. Springer, A. Kostka, J.F. dos Santos, D. Raabe, Influence of intermetallic phases and Kirkendall-porosity on the mechanical properties of joints between steel and aluminium alloys, Mat. Sci. Eng A 528, 4630-4642 (2011). DOI: https://doi.org/10.1016/j.msea.2011.02.057
• [13] P. Clérico, X. Mininger, L. Prévond, T. Baudin, A.L. Helbert, Compromise between magnetic shielding and mechanical strength of thin Al/Steel/Al sandwiches produced by cold roll bonding: Experimental and numerical approaches, J. Alloys Comp. 798, 67-81 (2019). DOI: https://doi.org/10.1016/j.jallcom.2019.05.243
• [14] F. Kong, Y. Chen, D. Zhang, Interfacial microstructure and shear strength of Ti-6Al-4V/TiAl laminate composite sheet fabricated by hot packed rolling, Mater. Design 32, 3167-3172 (2011). DOI: https://doi.org/10.1016/j.matdes.2011.02.052
• [15] H. Xiao, Z. Qi, C. Yu, C. Xu, Preparation and properties for Ti/Al clad plater generated by differential temperature rolling, J. Mater. Process. Tech. 249, 285-290 (2017). DOI: https://doi.org/10.1016/j.jmatprotec.2017.06.013
• [16] M. Yang, H. Ma, Z. Shen, D. Chen, Y. Deng, Microstructure and mechanical properties of Al-Fe meshing bonding interfaces manufactured by explosive welding, Trans. Nonferrous Met. Soc. China 29, 680-691 (2019). DOI: https://doi.org/10.1016/S1003-6326(19)64978-2
• [17] M. Fan, Z. Luo, Z. Fu, X. Guo, J. Tao, Vacuum hot pressing and fatigue behaviors of Ti/Al laminate composites, Vacuum 154, 101-109 (2018). DOI: https://doi.org/10.1016/j.vacuum.2018.04.047
• [18] H. Springer, A. Kostka, E.J. Payton, D. Raabe, A. Kaysser-Pyzalla, G. Eggler, On the formation and growth of intermetallic phases during interdiffusion between low-carbon steel and aluminium alloys, Acta Mater. 59, 1586-1600 (2011). DOI: https://doi.org/10.1016/j.actamat.2010.11.023
• [19] H. Springer, A. Szczepaniak, D. Raabe, On the role of zinc on the formation and growth of intermetallic phases during interdiffusion between steel and aluminium alloys, Acta Mater. 96, 203-211 (2015). DOI: https://doi.org/10.1016/j.actamat.2015.06.028
• [20] J. Yang, Y.L. Li, H. Zhang, W. Guo, Y. Zhou, Control of interfacial intermetallic compounds in Fe-Al joining by Zn addition, Mat. Sci. Eng. A 645, 323-327 (2015). DOI: https://doi.org/10.1016/j.msea.2015.08.036
• [21] C. Tan, C. Zang, H. Xia, X. Zhao, K. Zhang, S. Meng, B. Chen, X. Song, L. Li, Influence of Al additions in Zn-based filler metals on laser welding-brazing of Al/steel, J. Manuf. Process. 34, 251-263 (2018). DOI: https://doi.org/10.1016/j.jmapro.2018.06.008
• [22] W. Kowalski, H. Paul, P. Petrzak, Ł. Maj, I. Mania, M. Faryna, Influence of hot pressing on the microstructure of multi-layered Ti/Al composites, Arch. Metall. Mater. 66 4, 1149-1156 (2021). DOI: https://doi.org/10.24425/amm.2021.136435
• [23] W. Gąsior, A. Debski, Z. Moser, Formation enthalpy of intermetallic phases from Al-Fe system measured with solution calorimetric method, Intermetallics 24, 99-105 (2012). DOI: https://doi.org/10.1016/j.intermet.2012.02.001
• [24] R.T. Li, Z.L. Dong, K.A. Khor, Al-Cr-Fe quasicrystals as novel reinforcements in Ti based composites consolidated using high pressure spark plasma sintering, Mater. Design 102, 255-263 (2016). DOI: https://doi.org/10.1016/j.matdes.2016.04.040

Uwagi

1. The work was supported by The National Centre for Research and Development (NCBiR) in the frame of TECHMATSTRATEG2/412341/8/ NCBR/2019 (EMuLiReMat).

2. Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023).