The Influence of Abrasive Paste on the Effects of Vibratory Machining of Brass

• Autorzy: Bańkowski D. , Spadło S.

Identyfikatory

DOI

10.24425/afe.2019.129622

• Języki publikacji: EN

Abstrakty

EN

The article presents the results of research on the finishing of M63 Z4 brass by vibratory machining. Brass alloy was used for the research due to the common use of ammunition elements, cartridge case and good cold forming properties on the construction. Until now, the authors have not met with the results of research to determine the impact of abrasive pastes in container processing. It was found that the additive for container abrasive treatment of abrasive paste causes larger mass losses and faster surface smoothing effects. The treatment was carried out in two stages: in the first stage, the workpieces were deburred and then polished. Considerations were given to the impact of mass of workpieces, machining time and its type on mass loss and changes in the geometric structure of the surface. The surface roughness of machining samples was measured with the Talysurf CCI Lite optical profiler. The suggestions for future research may be to carry out tests using abrasive pastes with a larger granulation of abrasive grains, and to carry out tests for longer processing times and to determine the time after which the parameters of SGP change is unnoticeable.

Słowa kluczowe

EN

surface treatment; product development; vibratory machining; surface roughness; brass; finishing

PL

obróbka powierzchniowa; rozwój produktu; obróbka wibracyjna; chropowatość powierzchni; wykończenie; mosiądz

• Wydawca: Komisja Odlewnictwa Polskiej Akademii Nauk Oddział w Katowicach
• Czasopismo: Archives of Foundry Engineering
• Rocznik: 2019
• Tom: iss. 4
• Strony: 5--10
• Opis fizyczny: bibliogr. 21 poz., fot., rys., tab., wykr.

Twórcy

autor

Bańkowski D.

• Kielce University of Technology, Department of Materials Science and Materials Technology, Kielce, Poland

autor

Spadło S.

• Kielce University of Technology, Department of Materials Science and Materials Technology, Kielce, Poland

Bibliografia

• [1] Kondracki, M. & Szajnar, J. (2007). Possibilities for leaded brass replacement with multi-component brass. Archives of Metallurgy and Materials. 7(2), 57-64.
• [2] Konieczny, M. & Dziadoń, A. (2007). Mechanical behaviour of multilayer metal-intermetallic laminate composite synthesised by reactive sintering of Cu/Ti foils. Archives of Metallurgy and Materials. 52(4), 555-562.
• [3] Rokosz, K., Hryniewicz, T., Kacalak, W. et al. (2018). Characterization of porous phosphate coatings enriched with calcium, magnesium, zinc and copper created on cp titanium grade 2 by plasma electrolytic oxidation. Metals. 8(6), Article number 411.
• [4] Spadło, S., Młynarczyk, P. & Bańkowski, D. (2014). Analysis of the effect of processing vibro-abrasive finishing on the geometric structure surface scales ammunition and sharp edges. Journal of Achievements in Materials and Manufacturing Engineering. 66(1), 39-44.
• [5] Bańkowski, D. & Spadło, S. (2017). Vibratory machining effect on the properties of the aaluminum alloys surface. Archives of Foundry Engineering. 17(4), 19-24.
• [6] Woźniak, K. (2017). Surface treatment in container smoothing machines. Warszawa: WNT. (in Polish).
• [7] Wróbel, T., Szajanr, J., Bartocha, D. & Stawarz, M. (2017). Primary structure and mechanical properties of AlSi2 alloy continuous ingots. Archives of Foundry Engineering. 17(2), 145-150.
• [8] Bańkowski, D., Spadło, S (2018) Influence of ceramic media on the effects of tumbler treatment; Proceedings of 27th International Conference on Metallurgy and Materials Metal 2018, (pp. 1062-1066).
• [9] Eric, C., Ames. (2012). Repair of high-value high-demand spiral bevel gears by superfinishing. Gear Technology. October, 50-59.
• [10] Davidson, D.A. (2002). Mass Finishing Processes. 2002 Metal Finishing Guidebook and Directory. New York: TAM surfaces are Elsevier Science. Published 2002.
• [11] Glvan, D.O. et al (2018). Study on the influence of supplying compressed air channels and evicting channels on pneumatical oscillation systems for vibromooshing, IOP Conf. Ser.: Mater. Sci. Eng. 294 012069.
• [12] Massarsky. M.L. & Davidson. D.A. (2002). Turbo-abrasive machining – a new technology for metal and non-metal part finishing. The Finishing Line. 18(4). Dearborn MI: Association of Finishing Processes. Society of Manufacturing Engineers. Oct. 30. Published 2002.
• [13] Bańkowski, D., Spadło, S. (2016). Investigations of influence of vibration smoothing conditions of geometrical structure on machined surfaces. 4th International Conference Recent Trends In Structural Materials. Comat 2016; Volume: 179 Article Number: UNSP 012002 Published: 2017. DOI.org/10.1088/1757-899X/179/1/012002.
• [14] Swiercz, R., Oniszczuk-Swiercz, D. & Dabrowski, L. (2018). Electrical discharge machining of difficult to cut materials. Archive of Mechanical Engineering. 65(4). 461-476. DOI: 10.24425/ame.2018.125437.
• [15] Jedrzejczyk, D., Hajduga, M (2013). The influence of the kind of surface treatment on the wear of machines elements
• applied in the textile industry. 22nd International Conference on Metallurgy and Materials, Metal 2013, (pp: 880-885).
• [16] Bańkowski, D., Spadło S. (2015). Influence of the smoothing conditions in vibro-abrasive finishing and deburring process for geometric structure of the surface machine parts made of aluminum alloys EN AW2017. Proceedings of 24th International Conference on Metallurgy and Materials, Metal 2015, (pp. 1062-1068).
• [17] Fedoryszyn, A., Meksa, W.T. & Woźnicki, G. (2008). Performance tests of an abrasive cut-off systems for the finishing of high-precision casts. Archives of Metallurgy and Materials. 8(2), 33-36.
• [18] Wrona, R., Zyzaka, P., Ziółkowskia, E. & Brzeziński, M. (2012). Methodology of Testing Shot Blasting Machines in Industrial Conditions. Archives of Metallurgy and Materials. 12(2), 97-104.
• [19] Pietnickia, K., Wołowiec, E. & Klimek, L. (2011). Modeling of the number of stubble stuck elements after abrasive jet machining-processing. Archives of Metallurgy and Materials. 11(3), 51-54.
• [20] http://demet.pl/oferta/mosiadz/mosiadz-m63/.
• [21] Janecki, D., Stępień, K. & Adamczak, S. (2010). Problems of measurement of barrel- and saddle-shaped elements using the radial method. Measurement. 43(5), 659-663.

Uwagi

PL

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2019).