An Identification of the Material Hardening Parameters for Cyclic Loading - Experimental and Numerical Studies

• Autorzy: Skrzat A. , Wójcik M.

Identyfikatory

DOI

10.24425/amm.2020.132820

• Języki publikacji: EN

Abstrakty

EN

This paper presents the results of experimental studies and numerical simulations of the ratcheting for the PA6 aluminum. In the initial determination of the material hardening parameters, the samples were subjected to the symmetrical strain-controlled cyclic tension-compression test. The experimental stress-strain curve was compared with the numerical one obtained for non-linear Frederick-Armstrong and Voce models. For better fitting of both curves, the optimization procedure based on the least-square method and the fuzzy logic was applied. After establishing the hardening parameters, numerical simulations of the ratcheting were made. The boundary value problem was solved by means of discrete analysis. The data (force and displacement) obtained in numerical computations were used to control the ratchetting experiment. The results of experiments and numerical calculations were compared. Good convergence proves the reliability of the determination of material hardening data.

Słowa kluczowe

EN

ratchetting; cyclic plasticity; non-symmetrical stress load; finite element method

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2020
• Tom: Vol. 65, iss. 2
• Strony: 779--786
• Opis fizyczny: Bibliogr. 50 poz., fot., rys. wzory

Twórcy

autor

Skrzat A.

• Rzeszow University of Technology, Faculty of Mechanical Engineering and Aeronautics, Department of Materials Forming and Processing, 8 Powstańców Warszawy Ave., 35-959 Rzeszów, Poland

autor

Wójcik M.

• Rzeszow University of Technology, Faculty of Mechanical Engineering and Aeronautics, Department of Materials Forming and Processing, 8 Powstańców Warszawy Ave., 35-959 Rzeszów, Poland

Bibliografia

• [1] G. Kang, Int. J. Fatigue 30, 1448-1472 (2008).
• [2] M. Noban, H. Jahed, Int. J. Pres. Ves. Pip. 84, 223-233 (2007).
• [3] M. Shariati, H. Hatami, H. Yarahmadi, H. M. Eipakchi, Mater.Design 34, 302-312 (2011).
• [4] Q. Dong, P. Yang, G. Xu, Int. J. Nav. Archit. Ocean Eng. 11, 671-678 (2019).
• [5] S. S. Manson, G. R. Halford, Fatigue and Durability of Structural Materials, ASM International, Ohio (2006).
• [6] S. K. Paul, J. Mater. Res. Technol. 8, 4894-4914 (2019).
• [7] C.-B. Lim, K. S. Kim, J. B. Seong, Int. J. Fatigue 31, 501-507 (2009).
• [8] X. Yang, Int J Fatigue 27, 1124-1132 (2005).
• [9] Z. Zhang, X. Chen, T. Wang, Polym. Eng. Sci. 48, 29-36 (2007).
• [10] S. Guo, G. Kang, J. Zhang, Int. J. Plasticity 40, 101-125 (2013).
• [11] S. Guo, G. Kang, J. Zhang, Int. J. Plasticity 27, 1896-1915 (2011).
• [12] G. Kang, S. Guo, C. Dong, Mater. Sci. Eng. A 426, 66-76 (2006).
• [13] S. C. Kulkarni, Y. M. Desai, T. Kant, G. R. Reddy, Y. Parulekar, K. K. Vaze, Int. J. Pres. Ves. Pip. 80, 179-185 (2003).
• [14] N. Ohmo, M. Abdel-Karim, M. Kobayashi, T. Igari, Int. J. Plasticity 14, 355-372 (1998).
• [15] N. Ohno, M. Abdel-Karim, J. Eng. Mater. Technol. 122, 35-41 (2000).
• [16] G. Tao, Z. Xia, Polym. Test. 26, 451-460 (2007).
• [17] F. Alonso-Marroquin, H. J. Herrmann, Phys. Rev. Lett. 92, 1-4 (2004).
• [18] B. J. Gao, X. Chen, G. Chen, Int. J. Pressure Vessels Piping 83, 96-106 (2006).
• [19] X. Chen, R. Jiao, K. S.Kim, Int. J. Plasticity 21, 161-184 (2005).
• [20] K. Sasaki, K-i. Ohguchi, J. Electron. Mater. 40, 2403-2414 (2011).
• [21] M. Abdel-Karim, M. Mizuno, N. Ohno, J. Soc. Mater. Sci. 48, 104-109 (1999).
• [22] X. Chen, S. C. Hui, Polym. Test 24, 829-833 (2005).
• [23] X. Chen, R. Jiao, Int. J. Plast. 20 (4-5), 871-898 (2004).
• [24] O. U. Colak, Mater. Design. 29 (8), 1575-1581 (2008).
• [25] P.-A. Eggertsen, K. Mattiasson, Int. J. Mater. Form. 42 (2), 103-120 (2011).
• [26] T. Phongsai, W. Julsri, B. Chongthairungruang, S. Suranuntchai, S. Jirathearanat, V. Uthaisangsuk, Songklanakarin J. Sci. Technol. 38 (5), 485-493 (2016).
• [27] M. Rosenschon, S. Suttner, M. Merklein, Key Eng. Mater. 639, 385-392 (2015).
• [28] W. Bochniak, K. Marszowski, A. Korbel, J. Mater. Process. Technol. 169 (1), 44-53 (2005).
• [29] W. Bochniak, A. Korbel, J. Mater. Process. Technol. 134 (1), 120-134 (2003).
• [30] W. Bochniak, A. Korbel, P. Ostachowski, S. Ziółkiewicz, Obróbka Plastyczna Metali 24 (2), 83-87 (2013).
• [31] K. Pieła, L. Błaz, M. Jaskowski, Arch. Metall. Mater. 58 (3), 683-689 (2013).
• [32] D. Bańkowski, S. Spadło, Arch. Foundry Eng. 17, 19-24 (2017).
• [33] M. Wójcik, A. Skrzat, Continuum Mech. Thermodyn. 1-12 (2019), DOI: 10.1007/s00161-019-00805-y.
• [34] Y. Jiang, H. Sehitoglu, Int. J. Solids. Struct. 33, 1053-1068 (1996).
• [35] Y. E. Dafalias, E. Popov, Acta Mech. 21, 173-192 (1975).
• [36] G. Z. Voyiadjis, S. M. Sivakumar, Studies in Applied Mechanics 35, 253-295 (1994).
• [37] R. D. Krieg, ASME J. Appl. Mech.42, 641–646 (1975).
• [38] Y. Dafalias, E. Popov, ASME J. Appl. Mech. 43, 645-650 (1976).
• [39] J. L. Chaboche, Eur. J. Mech. A/Solid 13, 501-518 (1994).
• [40] N. Ohno, J. D. Wang, Int. J. Plasticity 9, 375-389 (1993).
• [41] Y. Jiang, P. Kurath, Int. J. Plast. 12, 387-415 (1996).
• [42] F. Dunne, N. Petrinic, Introduction to Computational Plasticity, Oxford University Press, New York (2005).
• [43] M. Aleyaasin, Mechanics of Finite Deformation and Fracture, Apple Academic Press, Oakville (2016).
• [44] K. Chung, T. Park, Int. J. Plast. 45, 61-84 (2013).
• [45] P. Thamburaja, B. Klusemann, S. Adibi, S. Bargmann, App. Phys. Lett. 106, 1-4 (2015).
• [46] B. Möller, M. Beer, Fuzzy Randomness, Springer-Verlag, Berlin Heildelberg (2004).
• [47] B. Möller, W. Graf, M. Beer, Comput Mech. 26, 547-565 (2000).
• [48] A. Skrzat, M. Wójcik, ZN Politechniki Rzeszowskiej. Mechanika 90 (4), 505-518 (2018).
• [49] A. Skrzat, Arch. Metall. Mater. 56, 559-568 (2011).
• [50] A. Skrzat, Wybrane problem eksperymentalnego i numerycznego wyznaczania naprężeń własnych w kołach pojazdów szynowych, Oficyna Wydawnicza Politechniki Rzeszowskiej, Rzeszów (2012).