The Microstructure and Mechanical Properties of Cylindrical Elements from Steel 38Mn6 after Continuous Induction Heating

• Autorzy: Smalcerz A. , Barglik J. , Kuc D. , Ducki K. , Wasiński S.

Identyfikatory

DOI

10.1515/amm-2016-0318,

• Języki publikacji: EN

Abstrakty

EN

The paper deals with the influence of induction surface hardening on the microstructure and mechanical properties of cylindrical elements made of steel 38Mn6. The first stage was based on computer simulation of the induction hardening process. The second stage - experiments were provided on laboratory stand for induction surface hardening located at the Silesian University of Technology. Microstructure tests were conducted on light and scanning microscopes. The hardness penetration pattern and thickness of hardened layer were marked. It was found that due to properly chosen parameters of the process, the appropriate properties and thickness of hardened layer were achieved.

Słowa kluczowe

EN

induction heating; computer simulation; induction surface hardening; microstructure

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2016
• Tom: Vol. 61, iss. 4
• Strony: 1969--1974
• Opis fizyczny: Bibliogr. 9 poz., rys., tab., wykr.

Twórcy

autor

Smalcerz A.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, 8 Krasińskiego Str. Poland

autor

Barglik J.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, 8 Krasińskiego Str. Poland

autor

Kuc D.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, 8 Krasińskiego Str. Poland

autor

Ducki K.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, 8 Krasińskiego Str. Poland

autor

Wasiński S.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, 8 Krasińskiego Str. Poland

Bibliografia

• [1] V. Rudnev, G. Totten, Induction Heating and Heat Treatment,. 2014 ASM Handbook, Materials Park, Ohio.
• [2] S. Zhu, Z. Wang, X Qin, H Mao, K. Gao, J Materials Eng and Performance, 24, 3919-3932 (2015).
• [3] J. Barglik, COMPEL, 35 (4), 1403-1417 (2016).
• [4] J. Barglik, A. Smalcerz, Comprehensive Materials Finishing, 2017, Elselvier, Oxford.
• [5] FLUX3D 10.2 User’s guide. Cedrat, Grenoble 2009,
• [6] QT Steel - Metallurgical Software for Simulating the Quench and Tempering of Steels, Ita Technology Software, Ostrava Czech Republic (2015)
• [7] P. Paszek, Numerical analysis of induction hardening axisymmetric elements, PhD thesis, Silesian University of Technology, Gliwice, 2015, June.
• [8] R. Przylucki, S. Golak, B. Oleksiak, L. Blacha, Arch Civ Mech Eng, 11 (1), 171-179 (2011).
• [9] J. Lipart, T. Matula, M. Niesler, L. Blacha, J. Filipczyk, Metalurgija, 52 (4), 493-496 (2013).

Uwagi

EN

The paper was prepared under the Research Project No. PBS2/A5/41/2014, financed by the National Research and Development Centre - Poland.