The Effect of the Length of the Drawing Die Sizing Portion on the Energy and Force Parameters of the Medium-Carbon Steel Wire Drawing Process

• Autorzy: Suliga M. , Jabłońska M. , Hawryluk M.

Identyfikatory

DOI

10.24425/amm.2019.130101

• Języki publikacji: EN

Abstrakty

EN

The paper discusses a theoretical and an experimental analyses of steel wire drawing in conical drawing dies with a varying length of the die sizing portion. The theoretical analysis was performed in the Drawing 2D, where the wire temperature and drawing stress were determined. The theoretical study was verified by the measurement of drawing force under laboratory conditions and by industrial multi-stage drawing tests carried out under commercial conditions. A relationship has been shown to exist between die sizing portion length and wire temperature and drawing stress.

Słowa kluczowe

EN

conical die; wire drawing; temperature; drawing stress

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2019
• Tom: Vol. 64, iss. 4
• Strony: 1353--1359
• Opis fizyczny: Bibliogr. 13 poz., fot., rys., tab., wzory

Twórcy

autor

Suliga M.

• Czestochowa University of Technology, Faculty of Production Engineering and Materials Technology, 19 Armii Krajowej Str., 42-201 Częstochowa, Poland

autor

Jabłońska M.

• Silesian University of Technology, Institute of Materials Engineering, 8 Krasińskiego Str., 40-019 Katowice, Poland

autor

Hawryluk M.

• Wroclaw University of Science and Technology, Department of Metal Forming and Metrology, 5 Lukasiewicza Str., 50-371 Wrocław, Poland

Bibliografia

• [1] M. Suliga, Analysis of the heating of steel wires during high speed multipass drawing process, Archives of Metallurgy and Materials 4 (59), 1475-1480 (2014).
• [2] T. Masse, L. Fourment, P. Montmitonnet, C. Bodadilla, S. Foissey, The optimal die semi-angle concept in wire drawing, examined using automatic optimization techniques, Int. J. Mater. Form. 6, 377-389 (2013).
• [3] L. K. Kabayama, S. P. Taguchi, G.A.S. Martinez, The influence of die geometry on stress distribution by experimental and FEM simulation on electrolytic copper wire drawing, Materials Research 12, 3, 281-285 (2009).
• [4] M. Asakawa, "MORDICA LECTURE" - Part 1: Trends in drawing technology for bars and wires, Wire Journal International 8, 60-66 (2014).
• [5] H. Overstam, The influence of bearing geometry on the residual stress state in cold drawn wire analysed by the FEM, Journal of Materials Processing Technology 171, 446-450 (2006).
• [6] J. Łuksza, Elementy ciągarstwa, AGH Uczelniane Wydawnictwa Naukowo-Techniczne, Kraków (2001).
• [7] Sang-Kon Lee, Won-Ho Hwang, Dae-Cheol Ko, Byung-Min Kim, Woo-Sik Ko, Pass schedule of wet-wire drawing process with ultra high speed for tire steel cord, Key Engineering Materials 340-341, 683-688 (2007).
• [8] M. Asakawa, S. Sasaki, S. Shishido, Effect of die approach geometry and bearing length on residual stress after bar drawing, Wire Journal International 10, 59-68 (2002).
• [9] B. Golis, J. W. Pilarczyk, F. Knap, Wybrane zagadnienia z teorii i praktyki ciągnienia, Cz. 5. Ciągnienie drutów stalowych niepokrytych, Politechnika Częstochowska, Częstochowa (1995).
• [10] J. G. Wistreich, The Fundamentals of wire drawing, Metallurgical Reviews 3, 10, 97-141 (1958).
• [11] J. Łuksza, L. Sadok, Wybrane zagadnienia z ciągarstwa, Skrypty Uczelnianie 1025, Kraków (1986).
• [12] F. Knap, R. Karuzel, Ł. Cieślak, Ciągnienie drutów, prętów i rur, Metalurgia Nr 36, Wyd. Wydz. Inżynierii Procesowej, Materiałowej i Fizyki Stosowanej Politechniki Częstochowskiej, Częstochowa (2004).
• [13] A. Milenin, P. Kustra, Mathematical model of warm drawing process of magnesium alloys in heated dies, Steel Research International 81, 9, 1251-1254 (2010).