Influence of filler and FDM printing parameters on PLA tensile strength

• Autorzy: Appusamy Anandha Moorthy , Karuppan Sivakumar , Subramaniyan Madheswaran , Chinnappan Balaji Ayyanar

Identyfikatory

DOI

10.14314/polimery.2024.2.3

Warianty tytułu

PL

Wpływ napełniacza i parametrów druku FDM na wytrzymałość na rozciąganie PLA

• Języki publikacji: EN

Abstrakty

EN

Influence of the filler (alumina, copper, carbon fiber) and FDM printing parameters on PLA tensile strength was investigated. FDM process parameters (raster angle, layer thickness, number of coatings) were optimized using the ANOVA test. It was found that the most important parameter is the raster angle. Tensile strength increases as the raster angle increases and the number of shells as well as layer thickness (larger number of infills) decreases. The highest strength was achieved for PLA/PLA-Al2O3.

PL

Zbadano wpływ napełniacza (tlenek glinu, miedź, włókno węglowe) i parametrów druku FDM na wytrzymałość na rozciąganie PLA. Parametry procesu FDM (kąt rastra, grubość warstwy wewnętrznej, liczba warstw zewnętrznych) optymalizowano za pomocą testu ANOVA. Stwierdzono, że najbardziej istotnym parametrem jest kąt rastra. Wytrzymałość na rozciąganie wzrasta wraz ze wzrostem kąta rastra oraz zmniejszeniem liczby warstw zewnętrznych jak również grubości warstwy wewnętrznej (większa liczba wypełnień). Największą wytrzymałość uzyskano dla PLA/PLA-Al2O3.

Słowa kluczowe

EN

fused deposition modeling; 3D printing; sandwich composites; tensile strength

PL

druk FDM; kompozyty typu sandwich; wytrzymałość na rozciąganie

• Wydawca: Sieć Badawcza Łukasiewicz – Instytut Chemii Przemysłowej
• Czasopismo: Polimery
• Rocznik: 2024
• Tom: Vol. 69, nr 2
• Strony: 92--102
• Opis fizyczny: Bibliogr. 74 poz., rys., tab., wykr.

Twórcy

autor

Appusamy Anandha Moorthy

• Department of Mechanical Engineering, Bannari Amman Institute of Technology, Sathyamangalam 638401, Tamilnadu, India

• https://orcid.org/0000-0001-5540-8941

autor

Karuppan Sivakumar

• Department of Mechanical Engineering, Bannari Amman Institute of Technology, Sathyamangalam 638401, Tamilnadu, India

• https://orcid.org/0000-0001-7569-9037

autor

Subramaniyan Madheswaran

• Department of Mechanical Engineering, Bannari Amman Institute of Technology, Sathyamangalam 638401, Tamilnadu, India

• https://orcid.org/0000-0001-7106-7104

autor

Chinnappan Balaji Ayyanar

• Department of Mechanical Engineering, Coimbatore Institute of Technology, Coimbatore 641014, Tamilnadu, India

• https://orcid.org/0000-0002-2044-4683

Bibliografia

• [1] Abdulhameed O., Al-Ahmari A., Ameen W. et al.: Advances in Mechanical Engineering 2019, 11(2). https://doi.org/10.1177/1687814018822880
• [2] Romero P.E., Arribas-Barrios J., Rodriguez- -Alabanda O. et al.: CIRP Journal of Manufacturing Science and Technology 2021, 32, 396. https://doi.org/10.1016/j.cirpj.2021.01.019
• [3] Klippstein H., Hassanin H., Diaz De Cerio Sanchez A. et al.: Advanced Engineering Materials 2018, 20(9), 1800290. https://doi.org/10.1002/adem.201800290
• [4] Durgun I., Ertan R.: Rapid Prototyping Journal 2014, 20(3), 228. https://doi.org/10.1108/RPJ-10-2012-0091
• [5] Sood A.K., Ohdar R.K., Mahapatra S.S.: Materials and Design 2010, 31(1), 287. https://doi.org/10.1016/j.matdes.2009.06.016
• [6] Upcraft S., Fletcher R.: Assembly Automation 2003, 23(4), 318. https://doi.org/10.1108/01445150310698634
• [7] Chua C.K., Feng C., Lee C.W. et al.: The International Journal of Advanced Manufacturing Technology 2005, 25, 26. https://doi.org/10.1007/s00170-004-1865-5
• [8] Masood S.H, Song W.Q.: Materials and Design 2004, 25(7), 587. https://doi.org/10.1016/j.matdes.2004.02.009
• [9] Smith W.C., Dean R.W.: Polymer Testing 2013, 32(8), 1306. https://doi.org/10.1016/j.polymertesting.2013.07.014
• [10] Kumar S., Kruth JP.: Materials and Design 2010, 31(2), 850. https://doi.org/10.1016/j.matdes.2009.07.045
• [11] Chua C.K., Chou S.M., Wong T.S.: The International Journal of Advanced Manufacturing Technology 1998, 14, 146. https://doi.org/10.1007/BF01322222
• [12] Singh R., Bedi P., Fraternali F. et al.: Composites Part B: Engineering 2016, 106, 20. https://doi.org/10.1016/j.compositesb.2016.08.039
• [13] Papon E.A., Haque A.: Journal of Reinforced Plastics and Composites 2018, 37(6), 381. https://doi.org/10.1177/0731684417750477
• [14] Dey A., Yodo N.: Journal of Manufacturing and Materials Processing 2019, 3(3), 64. https://doi.org/10.3390/jmmp3030064
• [15] Gao G., Xu F., Xu J.: Machines 2022, 10(9), 750. https://doi.org/10.3390/machines10090750
• [16] Singh J., Goyal KK., Kumar R. et al.: Polymer Composites 2022, 43(9), 5908. https://doi.org/10.1002/pc.26849
• [17] Vinoth Babu N., Venkateshwaran N., Rajini N. et al.: Materials Technology 2022, 37(9), 1008. https://doi.org/10.1080/10667857.2021.1915056
• [18] Kam M., Ipekci A., Şengül Ö.: Journal of Thermoplastic Composite Materials 2023, 36(1), 307. https://doi.org/10.1177/08927057211006459
• [19] Torres J., Cole M, Owji A. et al.: Rapid Prototyping Journal 2016, 22(2), 387. https://doi.org/10.1108/RPJ-07-2014-0083
• [20] Akhoundi B., Behravesh AH.: Experimental Mechanics 2019, 59, 883. https://doi.org/10.1007/s11340-018-00467-y
• [21] Hill N., Haghi M.: Rapid Prototyping Journal 2014, 20(3), 221. https://doi.org/10.1108/RPJ-04-2013-0039
• [22] Ahn S.H., Montero M., Odell D. et al.: Rapid Prototyping Journal 2002, 8(4), 248. https://doi.org/10.1108/13552540210441166
• [23] Marșavina L., Vălean C., Mărghitaș M. et al.: Engineering Fracture Mechanics 2022, 274, 108766. https://doi.org/10.1016/j.engfracmech.2022.108766
• [24] Alarifi IM.: Polymer Composites 2022, 43(8), 5353. https://doi.org/10.1002/pc.26838
• [25] Lee J., Huang A.: Rapid Prototyping Journal 2013, 19(4), 291. https://doi.org/10.1108/13552541311323290
• [26] Zhang Z., Long Y., Yang Z. et al.: Composites Part A: Applied Science and Manufacturing 2022, 162, 107162. https://doi.org/10.1016/j.compositesa.2022.107162
• [27] Shaik Y.P., Schuster J., Katherapalli H.R. et al.: Journal of Composites Science 2022, 6(1), 16. https://doi.org/10.3390/jcs6010016
• [28] Espalin D., Alberto Ramirez J., Medina F. et al.: Rapid Prototyping Journal 2014, 20(3), 236. https://doi.org/10.1108/RPJ-12-2012-0112
• [29] Le L., Rabsatt M.A., Eisazadeh H. et al.: International Journal of Lightweight Materials and Manufacture 2022, 5(2), 197. https://doi.org/10.1016/j.ijlmm.2022.01.003
• [30] Ahmad M.N., Ishak M.R., Mohammad Taha M. et al.: Polymers 2022, 14(11), 2140. https://doi.org/10.3390/polym14112140
• [31] Mohamed O.A., Masood S.H., Bhowmik J.L. et al.: Journal of Materials Engineering and Performance 2016, 25, 2922. https://doi.org/10.1007/s11665-016-2157-6
• [32] Khan S., Joshi K., Deshmukh S.: Materials Today: Proceedings 2022, 50(5), 2119. https://doi.org/10.1016/j.matpr.2021.09.433
• [33] Roberson D., Shemelya CM., MacDonald E. et al.: Rapid Prototyping Journal 2015, 21(2), 137. https://doi.org/10.1108/RPJ-12-2014-0165
• [34] Vishal K., Rajkumar K., Sabarinathan P. et al.: Silicon 2022, 14, 9379. https://doi.org/10.1007/s12633-022-01712-9
• [35] Lebedev S.M., Gefle O.S., Amitov E.T. et al.: The International Journal of Advanced Manufacturing Technology 2018, 97, 511. https://doi.org/10.1007/s00170-018-1953-6
• [36] Kaynak C., Varsavas S.D.: Journal of Thermoplastic Composite Materials 2019, 32(4), 501. https://doi.org/10.1177/0892705718772867
• [37] Prashantha K., Roger F.: Journal of Macromolecular Science, Part A 2017, 54(1), 24-9. https://doi.org/10.1080/10601325.2017.1250311
• [38] Daniel F., Patoary N.H., Moore A.L. et al.: The International Journal of Advanced Manufacturing Technology 2018, 99, 1215. https://doi.org/10.1007/s00170-018-2490-z
• [39] Hou Z., Tian X., Zhang J. et al.: Composite Structures 2018, 184, 1005. https://doi.org/10.1016/j.compstruct.2017.10.080
• [40] Ferreira R.T., Amatte I.C., Dutra T.A. et al.: Composites Part B: Engineering 2017, 124, 88. https://doi.org/10.1016/j.compositesb.2017.05.013
• [41] Hofstätter T., Pedersen D.B., Tosello G. et al.: Procedia CIRP 2017, 66, 312. https://doi.org/10.1016/j.procir.2017.03.171
• [42] Tian X., Liu T., Yang C. et al.: Composites Part A: Applied Science and Manufacturing 2016, 88, 198. https://doi.org/10.1016/j.compositesa.2016.05.032
• [43] Matsuzaki R., Ueda M., Namiki M. et al.: Scientific Reports 2016, 6, 23058. https://doi.org/10.1038/srep23058
• [44] Hofstätter T., Gutmann I.W., Koch T. et al.: “Distribution and Orientation of Carbon Fibers in Polylactic Acid Parts Produced by Fused Deposition Modeling”, Materials from ASPE Summer Topical Meeting 2016, Raleigh, United States, June 27-30, 2016.
• [45] Yao X., Luan C., Zhang D. et al.: Materials and Design 2017, 114, 424. https://doi.org/10.1016/j.matdes.2016.10.078
• [46] Ivey M., Melenka G.W., Carey J.P. et al.: Advanced Manufacturing: Polymer and Composites Science 2017, 3(3), 81. https://doi.org/10.1080/20550340.2017.1341125
• [47] Li N., Li Y., Liu S.: Journal of Materials Processing Technology 2016, 238, 218. https://doi.org/10.1016/j.jmatprotec.2016.07.025
• [48] Lanzotti A., Grasso M., Staiano G. et al.: Rapid Prototyping Journal 2015, 21(5), 604. https://doi.org/10.1108/RPJ-09-2014-0135
• [49] Chacón J.M., Caminero M.A., García-Plaza E. et al.: Materials and Design 2017, 124, 143. https://doi.org/10.1016/j.matdes.2017.03.065
• [50] Baca Lopez D.M., Ahmad R.: Polymers 2020, 12(3), 651. https://doi.org/10.3390/polym12030651
• [51] Galatas A., Hassanin H., Zweiri Y. et al.: Polymers 2018, 10(11), 1262. https://doi.org/10.3390/polym10111262
• [52] Radadiya V.A., Gandhi A.H.: Journal of The Institution of Engineers (India): Series C 2022, 103, 1049. https://doi.org/10.1007/s40032-022-00848-2
• [53] Singh Boparai K., Singh R., Singh H.: Rapid Prototyping Journal 2016, 22(2), 217. https://doi.org/10.1108/RPJ-04-2014-0052
• [54] Yang L., Li S., Zhou X. et al.: Synthetic Metals 2019, 253, 122. https://doi.org/10.1016/j.synthmet.2019.05.008
• [55] Yang L., Li S., Li Y. et al.: Journal of Materials Engineering and Performance 2019, 28, 169. https://doi.org/10.1007/s11665-018-3784-x
• [56] Mohanty A., Nag K.S., Bagal D.K. et al.: Materials Today: Proceedings 2022, 50(5), 893. https://doi.org/10.1016/j.matpr.2021.06.216
• [57] Ferretti P., Leon-Cardenas C., Santi G.M. et al.: Polymers 2021, 13(13), 2190. https://doi.org/10.3390/polym13132190
• [58] Lee J., Lee H., Cheon K.H. et al.: Additive Manufacturing 2019, 30, 100883. https://doi.org/10.1016/j.addma.2019.100883
• [59] Uddin M.S., Sidek M.F., Faizal M.A. et al.: Journal of Manufacturing Science and Engineering 2017, 139(8), 081018. https://doi.org/10.1115/1.4036713
• [60] Bamiduro O., Owolabi G., Haile M.A. et al.: Rapid Prototyping Journal 2019, 25(3), 462. https://doi.org/10.1108/RPJ-04-2018-0087
• [61] Waseem M., Salah B., Habib T. et al.: Polymers 2020, 12(12), 2962. https://doi.org/10.3390/polym12122962
• [62] Naveed N.: Materials Technology 2021, 36(5), 317. https://doi.org/10.1080/10667857.2020.1758475
• [63] Son T.A., Minh P.S., Do Thanh T.: Key Engineering Materials 2020, 863, 103. https://doi.org/10.4028/www.scientific.net/KEM.863.103
• [64] Sheoran AJ., Kumar H.: Materials Today: Proceedings 2020, 21(3), 1659. https://doi.org/10.1016/j.matpr.2019.11.296
• [65] Hanon M.M., Zsidai L., Ma Q.: Materials Today: Proceedings 2021, 42(5), 3089. https://doi.org/10.1016/j.matpr.2020.12.1246
• [66] Coogan T.J., Kazmer D.O.: Rapid Prototyping Journal 2017, 23(2), 414. https://doi.org/10.1108/RPJ-03-2016-0050
• [67] Khunt C.P., Makhesana M.A., Mawandiya B.K. et al.: Advances in Materials and Processing Technologies 2022, 8(sup2), 320. https://doi.org/10.1080/2374068X.2021.1927651
• [68] Garzon-Hernandez S., Garcia-Gonzalez D., Jérusalem A. et al.: Materials and Design 2020, 188, 108414. https://doi.org/10.1016/j.matdes.2019.108414
• [69] Banerjee D., Mishra S.B., Khan M.S. et al.: Materials Today: Proceedings 2020, 33(8), 5051. https://doi.org/10.1016/j.matpr.2020.02.842
• [70] Xu Z., Fostervold R., Razavi N.: Procedia Structural Integrity 2021, 33, 571. https://doi.org/10.1016/j.prostr.2021.10.063
• [71] Griffiths C.A., Howarth J., De Almeida-Rowbotham G. et al.: Journal of Cleaner Production 2016, 139, 74. https://doi.org/10.1016/j.jclepro.2016.07.182
• [72] Dave H.K., Prajapati A.R., Rajpurohit S.R. et al.: Advances in Materials and Processing Technologies 2022, 8(1), 576. https://doi.org/10.1080/2374068X.2020.1829951
• [73] Bhandari S., Lopez-Anido R.A., Gardner D.J.: Additive Manufacturing 2019, 30, 100922. https://doi.org/10.1016/j.addma.2019.100922
• [74] Liang L., Huang T., Yu S. et al.: Materials Letters 2021, 300, 130173. https://doi.org/10.1016/j.matlet.2021.130173