Hot Formability of Heat-Resistant Stainless Steel X15CrNiSi20-12

• Autorzy: Kawulok R. , Schindler I. , Navrátil H. , Ševčák V. , Sojka J. , Konečná K. , Chmiel B.

Identyfikatory

DOI

10.24425/amm.2020.132812

• Języki publikacji: EN

Abstrakty

EN

High-temperature plastic properties of heat-resistant stainless steel X15CrNiSi20-12 were assessed on the basis of hot tensile tests and nil strength tests. The results were supported by metallographic analyses using SEM and EDX analysis. The formability of the investigated steel can be divided into roughly three temperature areas. In the temperature range of 900°C to about 1050°C, formability was negatively affected by precipitation of carbide particles at grain boundaries. As the temperature rose to 1200°C, these particles dissolved, resulting in an increase in formability. Further temperature increases resulted in a relatively steep drop in formability caused by overheating of the material. The nil ductility temperature of 1280°C and the nil-strength temperature of 1362°C were determined. The Plastic and strength properties of the investigated material were compared with the deformation behavior of the reference steel X5CrNi18-10, which shows a significantly wider range of suitable forming temperatures.

Słowa kluczowe

EN

heat-resistant stainless steel; hot tension test; nil strength temperature; nil ductility temperature

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2020
• Tom: Vol. 65, iss. 2
• Strony: 727--734
• Opis fizyczny: Bibliogr. 36 poz., fot., rys., tab., wzory

Twórcy

autor

Kawulok R.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 15/2172, 708 00 Ostrava - Poruba, Czech Republic

autor

Schindler I.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 15/2172, 708 00 Ostrava - Poruba, Czech Republic

autor

Navrátil H.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 15/2172, 708 00 Ostrava - Poruba, Czech Republic

autor

Ševčák V.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 15/2172, 708 00 Ostrava - Poruba, Czech Republic

autor

Sojka J.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 15/2172, 708 00 Ostrava - Poruba, Czech Republic

autor

Konečná K.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 15/2172, 708 00 Ostrava - Poruba, Czech Republic

autor

Chmiel B.

• Třinecké Železárny, A. S., Průmyslová 1000, 739 61 Třinec, Czech Republic

Bibliografia

• [1] Y. Zhou, Y. Liu, X. Zhou, C. Liu, J. Yu, Y. Huang, H. Li, W. Li, J. Mater. Sci. Technol. 33, 1448-1456 (2017).
• [2] J. A. Lichtenfeld, M. C. Mataya, Ch. J. Van Tyne, Metall. Mater. Trans. A 37A, 147-161 (2006).
• [3] M. S. Ghazani, B. Eghbali, Mater. Sci. Eng. A 730, 380-390 (2018).
• [4] J. Fu, J. Sun, X. Cen, X. Zhang, F. Li, Y. Wu, Mater. Charact. 139, 241-248 (2018).
• [5] V. A. Hosseini, L. Karlsson, D. Engelberg, S. Wessman, Weld. World. 62, 517-533 (2018).
• [6] R. K. C. Nkhoma, C. W. Siyasiya, W. E. Stumpf, J. Alloys Compd. 595, 103-112 (2014).
• [7] R. V. Taiwade, R. Shukla, H. Vashishtha, A. V. Ingle, R. K. Dayal, ISIJ Int. 53 (12), 2206-2212 (2013).
• [8] J. Man, M. Smaga, I. Kuběna, D. Eifler, J. Polák, Eng. Fract. Mech. 185, 139-159 (2017).
• [9] W. H. Kan, V. Bhatia, K. Dolman, T. Lucey, X. Tang, L. Chang, G. Proust, J. Cairney, Wear. 389-399, 220-226 (2018).
• [10] D. Iacoviello, F. Iacoviello, M. Macario, La Metallurgia Italiana. 25 (3), 1-6 (2003).
• [11] M. Aghaie-Khafri, F. Honarvar, S. Zanganeh, J. Nondestruct. Eval. 31 (3), 191-196 (2012).
• [12] M. Žídek, Metalurgická tvařitelnost ocelí za tepla a za studena, ALEKO, Prague (1995).
• [13] R. Baron, R. Fabík, in: Metal 2011, Ostrava: Tanger Ltd, paper no. 951 (2011).
• [14] P. Turoňová, I. Schindler, P. Jonšta, M. Heger, J. Bořuta, L. Černý, in: Metal 2005, Ostrava: Tanger Ltd, paper no. 63 (2005).
• [15] L. Duprez, B. D. Cooman, N. Akdut, Steel Res. 71 (10), 417-422 (2000).
• [16] H. Sun, Y. Sun, R. Zhang, M. Wang, R. Tang, Z. Zhou, Mater. Des. 64, 374-380 (2014).
• [17] M. Schymura, R. Stegemann, A. Fischer, Int. J. Fatigue. 79, 25-35 (2015).
• [18] A. Moteshakker, I. Danaee, J. Mater. Sci. Technol. 32 (3), 282-290 (2016).
• [19] M. Vach, T. Kuníková, M. Dománková, P. Ševc, L’. Čaplovič, P. Gogola, J. Janovec, Mater. Charact. 59 (12), 1792-1798 (2008).
• [20] S. Das, M. Mukherjee, T. K. Pal, Eng. Failure Anal. 54, 90-102 (2015).
• [21] C. Hutchinson, H. Zurob, C. Sinclair, Y. Brechet, Scr. Mater. 59(6), 635-637 (2008).
• [22] O. Yoo, Y. J. Oh, B. S. Lee, S. W. Nam, Mater. Sci. Eng. A. 405 (1-2), 147-157 (2005).
• [23] W. M. Rainforth, M. P. Black, R. L. Higginson, E. J. Palmiere, C. M. Sellars, I. Prabst, P. Warbichler, F. Hofer, Acta Mater. 50(4), 735-747 (2002).
• [24] S. Jin, L. Guo, F. Luo, Z. Yao, S. Ma, R. Tang, Scr. Mater. 68 (2), 138-141 (2013).
• [25] P. Kawulok, I. Schindler, R. Kawulok, S. Rusz, P. Opěla, J. Kliber, M. Kawuloková, Z. Solowski, K. M. Čmiel, Metalurgija. 55 (3), 365-368 (2016).
• [26] I. Schindler, R. Mendrok, P. Kawulok, P. Unucka, R. Kawulok, P. Opěla, S. Rusz, R. Turoň, P. Turoňová, A. Bořuta, in: Metal 2014, Ostrava: Tanger Ltd, paper no. 2504 (2014).
• [27] A. Mertová, P. Kawulok, I. Schindler, B. Smetana, S. Zlá, R. Kawulok, S. Rusz, P. Opěla, Ľ. Drozdová, V. Ševčák, HutnickéListy 70 (6), 11-18 (2017).
• [28] A. F. Candelária, C. E. Pinedo, J. Mater. Sci. Lett. 22, 1151-1153 (2003).
• [29] X. Tao, J. Gu, L. Han, ISIJ Int. 54 (7), 1705-1714 (2014).
• [30] M. W. A. Rashid, M. Gakim, Z. M. Rosli, M. A. Azam, Int. J. Electrochem. Sci. 7, 9465-9477 (2012).
• [31] L. N. Bartlett, D. C. Van Aken, J. Medvedeva, D. Isheim, N. I. Medevedeva, K. Song, Metall. Mater. Trans. A. 45A, 2421-2435 (2014).
• [32] H. S. Khatak, B. Raj, Corrosion of Austenitic Stainless Steels; Mechanism, Mitigation and Monitoring. Cambridge: Woodhead Publishing Limited, 2002.
• [33] O. Martiník, B. Smetana, J. Dobrovská, S. Zlá, M. Kawuloková, K. Gryc, Ľ. Drozdová, P. Dostál, B. Martiníková, J. Phase Equilib. Diffus. 40 (1), 93-103 (2019).
• [34] J. Miettinen, A. A. Howe, Ironmaking Steelmaking. 27 (3), 212-227 (2000).
• [35] E. Kivineva, N. Suutala, Ruostumattomien terästen likviduslämötilojen riippuvuus koostumukseta, Report 5397-109/87, Outokumpu Oy, Tornio, Finland, 1987.
• [36] J. M. Cabrera-Marrero, V. Carreno-Galindo, R. D. Morales, F. Chavez-Alcala, ISIJ Int. 38 (8), 812-821 (1998).

Uwagi

EN

1. This paper was created at the Faculty of Materials Science and Technology within the Project No. CZ.02.1.01/0.0/0.0/17_049/0008399 funded by the Ministry of Education, Youth and Sports of the Czech Republic; and within the students’ grant project SP2020/88 supported at the VŠB – TU Ostrava by the Ministry of Education of the Czech Republic.

PL

2. Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2020).