Effect of brushing parameters upon edge states after wire brushing of AZ91 HP magnesium alloy

• Autorzy: Matuszak J. , Zaleski K.
• Języki publikacji: EN

Abstrakty

EN

When the tool leaves the part during machining operations, burrs can form as a result of material plastic flow. Wire brushing is one of burr removing methods. Low cost of brushes which can be mounted in a milling center gives the perspective of developing this method. The article was aimed at presenting the results of brushing process upon edge radius after wire brushing of AZ91HP magnesium alloy. Three kinds of brushes were tested with different types of fibers and the diameter of a single fiber. Brass and steel brushes were used.

Słowa kluczowe

EN

edge state; wire brushing; magnesium alloy

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2013
• Tom: Vol. 7, nr 20
• Strony: 55--60
• Opis fizyczny: Bibliogr. 15 poz., fig., tab.

Twórcy

autor

Matuszak J.

• Department of Production Engineering, Mechanical Engineering Faculty, Lublin University of Technology36 Nadbystrzycka Str., 20-618 Lublin, Poland

autor

Zaleski K.

• Department of Production Engineering, Mechanical Engineering Faculty, Lublin University of Technology36 Nadbystrzycka Str., 20-618 Lublin, Poland

Bibliografia

• 1. Aurich J.C., Dornfeld D., Arrazola P.J., Franke V., Leitz L., Min S. Burrs—Analysis, control and removal. CIRP Annals - Manufacturing Technology, 2009, 58(2): 519-542.
• 2. Chern G.-L. Experimental observation and analysis of burr formation mechanisms in face milling of aluminum alloys. International Journal of Machine Tools and Manufacture, 2006, 46(12-13): 1517-1525.
• 3. Cichosz P., Kuzinovski M. Metody wykonywania fazek i gratowania krawędzi. Cz. 1. Mechanik, 2011, 7: 353-359.
• 4. Cichosz P., Kuzinovski M. Metody wykonywania fazek i gratowania krawędzi. Cz. 2. Mechanik, 2011, 8-9: 674-681.
• 5. Fredj N.B., Nasr M.B., Rhouma A.B., Braham C., Sidhom H. Fatigue Life Improvements of the AISI 304 Stainless Steel Ground Surfaces by Wire Brushing. Journal of Materials Engineering and Performance, 2004, 13(5): 564-574.
• 6. Gillespie L.K., Blotter P.T. The Formation and Propierties of Machining Burrs. Journal of Engineering for Industry, 1976, 98: 66-74.
• 7. ISO, ISO13715:2000(E), in Technical drawings - Edges of undefined shape - Vocabulary and indications, 2000.
• 8. Kitahara H., Yada T., Hashiguchi F., Tsushida M., Ando S. Mg alloy sheets with a nanocrystalline surface layer fabricated by wire-brushing. Surface and Coatings Technology, 2012.
• 9. Kitahara H., Yada T., Tsushida M., Ando S. Microstructure and Evaluation of Wire-brushed Mg Sheets. Procedia Engineering, 2011, 10: 2737-2742.
• 10. Matuszak J., Zaleski K. Badania właściwości warstwy wierzchniej stopu aluminium po obróbce szczotkowaniem. [In:] Współczesne problemy w technologii obróbki przez nagniatanie. Ed. Przybylski W., 2011 (T.3): 307-318.
• 11. Matuszak J., Zaleski K. Effect of cutting fluids upon surface quality after wire brushing of 7075 aluminum alloys. [In:] Innovative manufacturing technology, Ed. P. Rusek, 2012: 203-214.
• 12. Matuszak J., Zaleski K. Effect of milling parameters upon burr formation during AZ91 HP Magnesium Alloy Face Milling. [In:] New materials and it technologies in production engineering. Ed. J. Lipski, A. Świć, LTN Lublin 2011: 31-42.
• 13. Oczoś K.E. Doskonalenie procesów obróbki ściernej. Cz. IV. Gładzenie, dogładzanie i obróbka luźnym ścierniwem. Mechanik, 2010, 11: 783-793.
• 14. Overholser R.W., Stango R.J., Fournelle R.A. Morphology of metal surface generated by nylon/abrasive filament brush. International Journal of Machine Tools and Manufacture, 2003, 43(2): 193-202.
• 15. Schmähling J., Hamprecht F.A. Generalizing the Abbott–Firestone curve by two new surface descriptors. Wear, 2007, 262(11-12): 1360-1371.