PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Influence of Carbon Fibre Reinforced Polymer and Recycled Carbon Fibres on the compressive behaviour of self-compacting high-performance fibre-reinforced concrete

Treść / Zawartość
Identyfikatory
Warianty tytułu
PL
Wpływ mat z włókien węglowych i włókien węglowych z recyklingu na efektywność wzmocnienia samozagęszczalnego fibrobetonu wysokowytrzymałościowego
Języki publikacji
EN
Abstrakty
EN
In recent years, carbon fibres have been extensively used to strengthen concrete structures. In most cases, the lamination process is carried out using epoxy resin as matrix. In some cases, especially when strengthen structural elements made of weak concrete, it is possible to replace the epoxy resin with an inorganic, cement matrix, while at the same time maintaining a sufficient efficiency of strengthen understood as the percentage increase in the compressive strength of concrete samples due to the applied reinforcement in relation to the reference concrete. In these studies, elements of carbon fibres mats that are reinforced with a cement matrix were used as the starting product for fibre recovery. The laminate, which was used to reinforce concrete elements, was detached from the concrete surface and subjected to processing in order to obtain clean carbon fibre scraps without cement matrix. Then, the obtained carbon material, in shaped form, was used to strengthen self-compacting, high performance, fibre reinforced concrete (SCHPFRC). For comparative purposes, this concrete was also strengthened by carbon fibre mats (with one and three layers of CFRP). Each samples were tested in uniaxial compression test. The compressive strength of concrete reinforced with 1 and 3 layers of CFRP was higher by 37.9 and 96.3%, respectively, compared to the reference concrete. On the other hand, the compressive strength of concrete reinforced with 1 and 3 layers of carbon fibre scrapswas higher by 11.8 and 40.1%, respectively. Regardless of the reinforcement technique used, the composite elements showed a higher deformability limit in comparison plain concrete. The obtained results showed that it is possible to reuse carbon fibre to strengthen structural elements made of SCHPFRC effectively, using simple processing methods.
PL
W ostatnich latach włókna węglowe są szeroko stosowane do wzmacniania konstrukcji betonowych. W większości przypadków proces laminowania odbywa się z użyciem żywicy epoksydowej jako matrycy. Czasami, zwłaszcza przy wzmacnianiu elementów konstrukcyjnych wykonanych z betonu o stosunkowo niskiej wytrzymałości na ściskanie, możliwe jest zastąpienie żywicy epoksydowej matrycą nieorganiczną; cementową, przy jednoczesnym zachowaniu dostatecznej efektywności wzmocnienia - rozumianej jako procentowy wzrost wytrzymałości betonu na ściskanie wskutek zastosowania materiału kompozytowego, w odniesieniu do betonu referencyjnego. W procesie kruszenia jako nadawę zastosowano elementy betonowe wzmocnione matami z włókien węglowych przy zastosowaniu matrycy cementowej. Laminat został oderwany od powierzchni betonu i poddany dalszej obróbce w celu uzyskania czystych, niezawierających matrycy cementowej skrawków mat z włókna węglowego. Następnie otrzymany materiał został wykorzystany do wzmocnienia samozagęszczalnego, wysokowytrzymałościowego fibrobetonu (SCHPFRC). Dla celów porównawczych beton ten został także wzmocniony z użyciem mat z włókien węglowych (1 i 3 warstwy wzmocnienia). Próbki cylindryczne przebadano w teście jednoosiowego ściskania. Wytrzymałość na ściskanie betonu wzmocnionego 1 i 3 warstwami CFRP była wyższa odpowiednio o 37,9 i 96,3% w porównaniu z betonem referencyjnym. Natomiast wytrzymałość betonu wzmocnionego 1 i 3 warstwami strzępów z włókna węglowego była wyższa odpowiednio o 11,8 i 40,1%. Niezależnie od zastosowanej techniki wzmocnienia, próbki kompozytowe cechowały się wyższą odkształcalnością graniczną w odniesieniu do betonu referencyjnego. Uzyskane wyniki wykazały, że możliwe jest wykorzystanie włókien węglowych z recyklingu do efektywnego wzmocnienia elementów konstrukcyjnych wykonanych z SCHPFRC, przy użyciu nieskomplikowanej metody przeróbki odpadu.
Rocznik
Strony
53--64
Opis fizyczny
Bibliogr. 20 poz., il., tab.
Twórcy
  • Cracow University of Technology, Faculty of Civil Engineering, Cracow, Poland
  • Cracow University of Technology, Faculty of Civil Engineering, Cracow, Poland
Bibliografia
  • [1] A.M. Poppe and G. De Schutter, “Influence of the nature and the grading curve of the powder on the rheology of self-compacting concrete”, in SP-200: Fifth CANMET/ACI International Conference on Recent Advances in Concrete Technology. ACI, 2001, pp. 399-414.
  • [2] H. Okamura and M. Ouchi, “Self-compacting concrete”, Journal of Advanced Concrete Technology, vol. 1, no. 1, pp. 5-15, 2003, doi: 10.3151/jact.1.5.
  • [3] A. Kostrzanowska-Siedlarz and J. Gołaszewski, “Rheological properties of high performance self-compacting concrete: effects of composition and time”, Construction and Building Materials, vol. 115, pp. 705-715, 2016, doi: 10.1016/j.conbuildmat.2016.04.027.
  • [4] M. Nuruzzaman, J.O.C. Casimiro, and P.K. Sarker, “Fresh and hardened properties of high strength self-compacting concrete using by-product ferronickel slag fine aggregate”, Journal of Building Engineering, 2020, vol. 32, doi: 10.1016/j.jobe.2020.101686.
  • [5] R.D.A. Hafez, B.A. Tayeh, and K. Abdelsamie, “Manufacturing nano novel composites using sugarcane and eggshell as an alternative for producing nano green mortar”, Environmental Science and Pollution Research, vol. 29, pp. 34984-35000, 2022, doi: 10.1007/s11356-022-18675-4.
  • [6] A.A. Hashim, Z.K. Rodhan, and S.J. Abbas, “Fresh and hardened properties of self-compacting high performance concrete containing nano-metakaolin as a partial replacement”, IOP Conference Series: Materials Science and Engineering, vol. 928, 2020, doi: 10.1088/1757-899X/928/2/022036.
  • [7] K. Ostrowski, et al., “Potential use of granite waste sourced from rock processing for the application as coarse aggregate in high-performance self-compacting concrete”, Construction and Building Materials, vol. 238, 2020, doi: 10.1016/j.conbuildmat.2019.117794.
  • [8] T. Ponikiewski, et al., “Determination of 3D porosity in steel fibre reinforced SCC beams using X-ray computed tomography”, Construction and Building Materials, vol. 68, pp. 333-340, 2014, doi: 10.1016/j.conbuildmat.2014.06.064.
  • [9] T. Ponikiewski and J. Katzer, “Fresh mix characteristics of self-compacting concrete reinforced by fibre”, Periodica Polytechnica Civil Engineering, vol. 61, no. 2, pp. 226-231, 2017, doi: 10.3311/PPci.9008.
  • [10] K. Ostrowski, et al., “The effect of the morphology of coarse aggregate on the properties of self-compacting high-performance fibre-reinforced concrete”, Materials, vol. 11, no. 8, 2018, doi: 10.3390/ma11081372.
  • [11] K.A. Ostrowski and K. Furtak, “The influence of concrete surface preparation on the effectiveness of reinforcement using carbon fibre-reinforced polymer in high-performance, self-compacting, fibre-reinforced concrete”, Composite Structures, vol. 276, 2021, doi: 10.1016/j.compstruct.2021.114522.
  • [12] B. Fu, et al., “Concrete reinforced with macro fibres recycled from waste GFRP”, Construction and Building Materials, vol. 310, 2021, doi: 10.1016/j.conbuildmat.2021.125063.
  • [13] H. Shima, H. Takahashi, and J. Mizuguchi, “Recovery of glass fibers from fiber reinforced plastics”, Materials Transactions, vol. 52, no. 6, pp. 1327-1329, 2011, doi: 10.2320/matertrans.M2011044.
  • [14] W. Głodkowska and M. Ruchwa, “Static analysis of reinforced concrete beams strengthened with CFRP composites”, Archives of Civil Engineering, vol. 56, no. 2, pp. 111-122, 2010, doi: 10.2478/v.10169-010-0006-9.
  • [15] C. Xiong, et al., “Sustainable use of recycled carbon fiber reinforced polymer and crumb rubber in concrete: Mechanical properties and ecological evaluation”, Journal of Cleaner Production, vol. 279, 2021, doi: 10.1016/j.jclepro.2020.123624.
  • [16] M. Kimm, et al., “Potential of using recycled carbon fibers as reinforcing material for fiber concrete”, in Fibre reinforced concrete: improvements and innovations, RILEM Bookseries, vol. 30. Springer, 2021, pp. 949-960, doi: 10.1007/978-3-030-58482-5_83.
  • [17] S. Nassiri, et al., “Mechanical and durability characteristics of pervious concrete reinforced with mechanically recycled carbon fiber composite materials”, Materials and Structures, vol. 54, art. no. 107, 2021, doi: 10.1617/s11527-021-01708-8.
  • [18] E. Pakdel, et al., “Recent progress in recycling carbon fibre reinforced composites and dry carbon fibre wastes”, Resources, Conservation and Recycling, vol. 166, 2021, doi: 10.1016/j.resconrec.2020.105340.
  • [19] Scopus. [Online]. Available: www.scopus.com. [Accessed: 25.03.2022].
  • [20] EN 12350-8:2009 Testing fresh concrete - Part 8: Self-compacting concrete - Slump flow test.
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-700ccca7-42a9-479b-99ac-a46ea77c5f35
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.