Local resistance of heating molybdenum sheet in a test device

• Autorzy: Mitka M. , Bastovansky R. , Brumercik F. , Ignaciuk P.

Identyfikatory

DOI

10.12913/22998624/74182

• Języki publikacji: EN

Abstrakty

EN

Large demand for bulk of sapphire optical products, which are widely used as illuminators, optical windows in aviation and aeronautics etc., generates the inquiry of effective production of high quality industrial crystals. The technology of crystal growth with the horizontal single crystal sapphire crystallization method is based on putting the crystal seed into the front of the crucible resistant to temperatures up to 2150°C. Without encompassment of the production technology of this special container made from thin molybdenum sheet is not realistic to consider the productive exploitation of horizontal crystallization systems in engineering practice. This paper presents the analysis of the possibility of the local resistance of molybdenum sheet heating by its deep drawing to obtain better drawing properties by increased blank temperature.

Słowa kluczowe

EN

molybdenum; resistance heating; deep drawing

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2017
• Tom: Vol. 11, no 3
• Strony: 87--93
• Opis fizyczny: Bibliogr. 24 poz., fig., tab.

Twórcy

autor

Mitka M.

• University of Zilina, Faculty of Mechanical Engineering, Department of Design and Machine Elements, Univerzitna 1, 010 26 Zilina, Slovakia

autor

Bastovansky R.

• University of Zilina, Faculty of Mechanical Engineering, Department of Design and Machine Elements, Univerzitna 1, 010 26 Zilina, Slovakia

autor

Brumercik F.

• University of Zilina, Faculty of Mechanical Engineering, Department of Design and Machine Elements, Univerzitna 1, 010 26 Zilina, Slovakia

autor

Ignaciuk P.

• Lublin University of Technology, Faculty of Mechanical Engineering, Institute of Transport, Internal Combustion Engines and Ecology, 36 Nadbystrzycka Street, 20-618 Lublin, Poland

Bibliografia

• 1. Arab. N., Nazaryan E. A., Arakelyan M.: Investigation to production molybdenum container to growth single crystals by deep drawing process. International Journal of Mechanical and Materials Engineering (IJMME), 1 (5), 2010, 116-122.
• 2. Brumercik F., Brumercikova E., Bukova B.: Mechatronic and Transport System Simulation. Applied mechanics and materials, 803, 2015, 201-206.
• 3. Caban J., Drozdziel P., Vrabel J., Sarkan B., Marczuk A., Krzywonos L., Rybicka I.: The research on ageing of glycol-based brake fluids of vehicles in operation. Advances in Science and Technology, 32 (10), 2016, 9-16.
• 4. Caban J., Marczuk A., Sarkan B., Vrabel J.: Studies on operational wear of glycol-based brake fluid. Przemysł Chemiczny. 10 (94), 2015, 1802-1806.
• 5. Faturik L., Trsko L., Hrcek S., Bokuvka O.: Comparison of structural design in high and ultra-high cycle fatigue regions. Transactions of FAMENA, 4 (38), 2014, 1-12.
• 6. Gardyński L., Lonkwic P.: Testing polymer rollers memory in the context of passenger lift car comfort. Journal of vibroengineering. 1 (16), 2014, 225-230.
• 7. Glowacz A.: Diagnostics of DC and Induction Motors Based on the Analysis of Acoustic Signals. Measurement Science Review, 5 (14), 2014, 257-262.
• 8. Cheng J., Nemat-Nasser S., Guo W.: A unified constitutive model for strain-rate and temperature dependent behavior of molybdenum. Mechanics of materials, 33, 2001, 603-616.
• 9. Kołtunowicz T. N., Zukowski P., Sidorenko J., Bayev V., Fedotova J. A., Opielak M., Marczuk A.: Ferromagnetic resonance spectroscopy of CoFeZr- Al2O3 granular films containing “FeCo core – oxide shell” nanoparticles. Journal of Magnetism and Magnetic Materials, 421, 2017, 98–102.
• 10. Krolczyk G. M., Nieslony P., Krolczyk J. B., Samardzic I., legutko S., Hloch S., Barrans S., Maruda R. W.: Influence of argon pollution on the weld surface morphology. Measurement, 70, 2015, 203-213.
• 11. Krolczyk J. B., Gapinski B., Krolczyk G. M., Samardzic I., Maruda R. W., Soucek K., Legutko S., Nieslony P., Javadi Y., Stas L.: Topographic inspection as a method of weld joint diagnostic. Technical Gazette, 1 (23), 2016, 301-306.
• 12. Marczuk A., Caban J., Savinykh P., Turubanov N, Zyryanov D.: Maintenance research of a horizontal ribbon mixer. Eksploatacja i Niezawodnosc – Maintenance and Reliability, 1 (19), 2017, 121–125.
• 13. Martikan, M., Brumercik F., Bastovansky R.: Development of Mechatronic Deformation System. Applied mechanics and materials, 803, 2015, 173-178.
• 14. Meng B., Wan M., Wu X., Zhou Y, Chang Ch.: Constitutive modeling for high-temperature tensile deformation behavior of pure molybdenum considering strain effects. journal of refractory metals and hard materials, 45, 2014, 41-47.
• 15. Meng B., Wan M., Wu X., Zhou Y.: Development of thermal deep drawing system with vacuum environment for difficult-to-deformation materials. Trans. Nonferrous Met. Soc. China. 22, 2012, 254−260.
• 16. Meng B., Fu W. M., Wan M.: Drawability and frictional behavior of pure molybdenum sheet in deep-drawing process at elevated temperature. Journal of advanced manufacturing technology, 78, 2015, 1005-1014.
• 17. Rudawska A.: Influence of the thickness of joined elements on lap length of aluminium alloy sheet bonded joints. Advances in Science and Technology Research Journal, 27 (9), 2015, 35–44.
• 18. Sawicki B., Miaskowski A.: Nonlinear higher-order transient solver for magnetic fluid hyperthermia. Journal of Computational and Applied Mathematics, 270, 2014, 143–151.
• 19. Skalskyi V. R., Makeev V. F., Stankevych O. M., Kyrmanov O. S., Vinnytska S. I.: Alternation of the types of fracture for dental polymers in different stages of crack propagation. Materials Science, 6 (50), 2015, 836-843.
• 20. Swić, A., Draczew, A., Gola, A.: Technology of heat treating-straightening of long shafts with low rigidity. Advances in Science and Technology Research Journal, 31 (10), 2016, 207-214.
• 21. Swić, A., Draczew, A., Gola, A.: Method of achieving accuracy of thermo-mechanical treatment of low-rigidity shafts. Advances in Science and Technology Research Journal, 29 (10), 2016, 62-70.
• 22. Walczak M., Pieniak D., Zwierzchowski M. The tribological characteristics of SiC particle reinforced aluminium composites. Archives of Civil and Mechanical Engineering, 1 (15), 2015, 116–123.
• 23. Walczak M., Zwierzchowski M., Bieniaś J., Caban J.: The tribological characteristics of Al-Si/graphite composite. Tribologia 1/2017, 97–104.
• 24. Zmindak, M., Donic, T., Jurik, P.: Numerical simulation of rectangular deep draw containers made from thin molybdenum sheet. IOP conference series: Materials science and engineering. 159, 2016, 8.

Uwagi

Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę (zadania 2017)