Transient forced vibration response analysis of heterogeneous sandwich circular plates under viscoelastic boundary support

• Autorzy: Alipour M. M.

Identyfikatory

DOI

10.1016/j.acme.2017.05.007

• Języki publikacji: EN

Abstrakty

EN

For the first time the transient bending analysis of a sandwich plate with viscoelastic boundary support is investigated in this study. Viscoelastic support consists of two sets of translational springs and dashpots connected in parallel along the in-plane and transverse directions. The sandwich plate is fabricated from heterogeneous face sheets where the material properties of each face sheets are assumed to be varied continuously in the radial direction according to a power-law function. Variations of the material properties of each face sheets are monitored by eight distinct inhomogeneity parameters. Therefore, the solution procedure may be used for a wide range of the practical problems. In order to investigate the effects of viscoelastic edge supports on the transient response of sandwich plate a wide range of the stiffness and damping coefficients of the edge supports in the in-plane and transverse directions are applied. Results of sandwich plates with the classical edge conditions as some special cases of the elastic/viscoelastic supports are compared with those extracted from the ABAQUS software based on the 3D theory of elasticity. The comparisons show that even for relatively complicated cases, there is a good agreement between the results.

Słowa kluczowe

EN

transient bending; sandwich structures; heterogeneous plate; semi-analytical method; viscoelastic boundary support

PL

metoda półanalityczna; zginanie; lepkosprężystość

• Wydawca: Springer ; Wrocław University of Science and Technology
• Czasopismo: Archives of Civil and Mechanical Engineering
• Rocznik: 2018
• Tom: Vol. 18, no. 1
• Strony: 12--31
• Opis fizyczny: Bibliogr. 54 poz., wykr.

Twórcy

autor

Alipour M. M.

• Department of Mechanical Engineering, University of Mazandaran, Babolsar 47416-13534, Iran

Bibliografia

• [1] H.S. Shen, J. Yang, L. Zhang, Dynamic response of Reisner– Mindlin plates under thermomechanical loading and resting on elastic foundation, Journal of Sound and Vibration 232 (2) (2000) 309–329.
• [2] O. Civalek, Nonlinear analysis of thin rectangular plates on Winkler–Pasternak elastic foundations by DSC–HDQ methods, Applied Mathematical Modelling 31 (2007) 606–624.
• [3] P. Ribeiro, Non-linear forced vibrations of thin/thick beams and plates by the finite element and shooting methods, Computers & Structures 82 (2004) 1413–1423.
• [4] P. Ribeiro, Forced periodic vibrations of laminated composite plates by a p-version, first order shear deformation, finite element, Composites Science and Technology 66 (2006) 1844– 1856.
• [5] W.L.A. Pereira, V.J. Karam, J.A.M. Carrer, W.J. Mansur, A dynamic formulation for the analysis of thick elastic plates by the boundary element method, Engineering Analysis with Boundary Elements 36 (2012) 1138–1150.
• [6] H.M. Sedighi, F. Daneshmand, J. Zare, The influence of dispersion forces on the dynamic pull-in behavior of vibrating nano-cantilever based NEMS including fringing field effect, Archives of Civil and Mechanical Engineering 14 (2014) 766–775.
• [7] B. Khalfi, A. Ross, Transient and harmonic response of a sandwich with partial constrained layer damping: a parametric study, Composites Part B: Engineering 91 (2016) 44–55.
• [8] L. Sator, V. Sladek, J. Sladek, L. Young Sator, V. Sladek, J. Sladek, D.L. Young, Elastodynamics of FGM plates by mesh-free method, Composite Structures 140 (2016) 309–322.
• [9] Z.X. Wanga, H.S. Shen, Nonlinear dynamic response of sandwich plates with FGM face sheets resting on elastic foundations in thermal environments, Ocean Engineering 57 (2013) 99–110.
• [10] A.R. Mojdehi, A. Darvizeh, A. Basti, H. Rajabi, Three dimensional static and dynamic analysis of thick functionally graded plates by the meshless local Petrov– Galerkin (MLPG) method, Engineering Analysis with Boundary Elements 35 (2011) 1168–1180.
• [11] M.M. Alipour, M. Shariyat, Semi-analytical consistent zigzag-elasticity formulations with implicit layerwise shear correction factors for dynamic stress analysis of sandwich circular plates with FGM layers, Composites Part B: Engineering 49 (2013) 43–64.
• [12] M.M. Alipour, M. Shariyat, Analytical zigzag-elasticity transient and forced dynamic stress and displacement response prediction of the annular FGM sandwich plates, Composite Structures 106 (2013) 426–445.
• [13] T. Kocatürk, G. Altintas, Determination of the steady-state response of viscoelastically point-supported rectangular orthotropic plates, Mechanics of Composite Materials 39 (5) (2003) 455–466.
• [14] T. Kocatürk, S. Sezer, C. Demir, The effect of support locations on the steady-state response of viscoelastically point-supported rectangular orthotropic plates, Archive of Applied Mechanics 75 (2005) 58–67.
• [15] M. Stembalski, W. Skoczyński, A. Roszkowski, P. Preś, Testing the vibration damping of a glass gatherer robot arm using a friction damper, Archives of Civil and Mechanical Engineering 17 (2017) 240–248.
• [16] F. Alinaghizadeh, M. Shariati, Geometrically non-linear bending analysis of thick two-directional functionally graded annular sector and rectangular plates with variable thickness resting on non-linear elastic foundation, Composites Part B 86 (2016) 61–83.
• [17] F. Alinaghizadeh, M. Shariati, Buckling analysis of variable thickness radially functionally graded annular sector plates resting on two-parameter elastic foundations by the GDQ method, International Journal of Applied Mechanics 7 (2015) 1550083.
• [18] Sh. Hosseini-Hashemi, H. Rokni Damavandi Taher, H. Akhavan, Vibration analysis of radially FGM sectorial plates of variable thickness on elastic foundations, Composite Structures 92 (2010) 1734–1743.
• [19] Sh. Hosseini-Hashemi, H. Akhavan, H. Rokni Damavandi Taher, N. Daemi, A. Alibeigloo, Differential quadrature analysis of functionally graded circular and annular sector plates on elastic foundation, Materials and Design 31 (2010) 1871–1880.
• [20] A. Nosier, F. Fallah, Non-linear analysis of functionally graded circular plates under asymmetric transverse loading, International Journal of Non-Linear Mechanics 44 (2009) 928– 942.
• [21] S.Y. Lee, S.M. Lin, Levy-type solution for the analysis of nonuniform plates, Computers & Structures 49 (6) (1993) 931– 939.
• [22] L.G. Nallim, B.M. Luccioni, R.O. Grossi, Vibration of general triangular composite plates with elastically restrained edges, Thin-Walled Structures 43 (2005) 1711–1745.
• [23] L.G. Nallim, R.O. Grossi, Vibration of angle-ply symmetric laminated composite plates with edges elastically restrained, Composite Structures 81 (2007) 80–83.
• [24] L.G. Nallim, R.O. Grossi, Natural frequencies of symmetrically laminated elliptical and circular plates, International Journal of Mechanical Sciences 50 (2008) 1153–1167.
• [25] R. Vescovini, C. Bisagni, Single-mode solution for post-buckling analysis of composite panels with elastic restraints loaded in compression, Composites Part B: Engineering 43 (2012) 1258–1274.
• [26] E. Bahmyari, A. Rahbar-Ranji, Free vibration analysis of orthotropic plates with variable thickness resting on non-uniform elastic foundation by element free Galerkin method, Journal of Mechanical Science and Technology 26 (9) (2012) 2685–2694.
• [27] A.S. Ashour, Vibration of angle-ply symmetric laminated composite plates with edges elastically restrained, Composite Structures 74 (2006) 294–302.
• [28] L.B. Rao, C.K. Rao, Fundamental buckling of circular plates with elastically restrained edges and resting on concentric rigid ring support, Frontiers of Mechanical Engineering 8 (3) (2013) 291–297.
• [29] L.B. Rao, C.K. Rao, Buckling of circular plate with foundation and elastic edge, International Journal of Mechanical and Materials Engineering 11 (2015) 149–156.
• [30] L.B. Rao, C.K. Rao, Frequencies of circular plate with concentric ring and elastic edge support, Frontiers of Mechanical Engineering 9 (2) (2014) 168–176.
• [31] L.B. Rao, C.K. Rao, Frequency analysis of annular plates with inner and outer edges elastically restrained and resting on Winkler foundation, International Journal of Mechanical Sciences 81 (2014) 184–194.
• [32] Q. Chen, P. Qiao, Post-buckling behavior of imperfect laminated composite plates with rotationally-restrained edges, Composite Structures 125 (2015) 117–126.
• [33] G. Jin, H. Chen, J. Du, T. Yang, W. Li, The influence of edge restraining stiffness on the transverse vibrations of rectangular plate structures, Journal of Marine Science and Application 9 (2010) 393–402.
• [34] P. Malekzadeh, M.R. Golbahar Haghighi, M.M. Atashi, Free vibration analysis of elastically supported functionally graded annular plates subjected to thermal environment, Meccanica 46 (2011) 893–913.
• [35] A. Sharma, Free vibration of moderately thick antisymmetric laminated annular sector plates with elastic edge constraints, International Journal of Mechanical Sciences 83 (2014) 124–132.
• [36] P.C. Dumir, C.H.R. Kumar, M.L. Gandhi, Nonlinear axisymmetric vibration of orthotropic thin circular plates with elastically restrained edges, Computers & Structures 22 (4) (1986) 677–686.
• [37] M.L. Gandhi, P.C. Dumir, Y. Nath, Nonlinear axisymmetric static analysis of orthotropic thin circular plates with elastically restrained edge, Computers & Structures 20 (5) (1985) 841–853.
• [38] Q. Wang, D. Shi, Q. Liang, X. Shi, A unified solution for vibration analysis of functionally graded circular, annular and sector plates with general boundary conditions, Composites Part B: Engineering 88 (2016) 264–294.
• [39] T. Ye, G. Jin, Z. Su, Y. Chen, A modified Fourier solution for vibration analysis of moderately thick laminated plates with general boundary restraints and internal line supports, International Journal of Mechanical Sciences 80 (2014) 29–46.
• [40] Y. Zhang, J. Du, T. Yang, Z. Liu, A series solution for the in-plane vibration analysis of orthotropic rectangular plates with elastically restrained edges, International Journal of Mechanical Sciences 79 (2014) 15–24.
• [41] D. Shi, Q. Wang, X. Shi, F. Pang, A series solution for the in-plane vibration analysis of orthotropic rectangular plates with non-uniform elastic boundary constraints and internal line supports, Archive of Applied Mechanics 85 (2015) 51–73.
• [42] F.A. Fazzolaria, E. Carrera, Free vibration analysis of sandwich plates with anisotropic face sheets in thermal environment by using the hierarchical trigonometric Ritz formulation, Composites Part B: Engineering 50 (2013) 67–81.
• [43] E. Carrera, S. Brischetto, A survey with numerical assessment of classical and refined theories for the analysis of sandwich plates, Applied Mechanics Reviews 62 (1) (2008) 010803– 010819.
• [44] E. Carrera, On the use of the Murakami's zig-zag function in the modeling of layered plates and shells, Computers and Structures 82 (2004) 541–554.
• [45] M.M. Alipour, A novel economical analytical method for bending and stress analysis of functionally graded sandwich circular plates with general elastic edge conditions, subjected to various loads, Composites Part B: Engineering 95 (2016) 48–63.
• [46] M.M. Alipour, Effects of elastically restrained edges on FG sandwich annular plates by using a novel solution procedure based on layerwise formulation, Archives of Civil and Mechanical Engineering 16 (2016) 678–694.
• [47] M.M. Alipour, M. Shariyat, An analytical global-local Taylor transformation-based vibration solution for annular FGM sandwich plates supported by nonuniform elastic foundations, Archives of Civil and Mechanical Engineering 14 (2014) 6–24.
• [48] M.M. Alipour, An analytical approach for bending and stress analysis of cross/angle-ply laminated composite plates under arbitrary non-uniform loads and elastic foundations, Archives of Civil and Mechanical Engineering 16 (2) (2016) 193–210.
• [49] M.M. Alipour, M. Shariyat, Analytical zigzag formulation with 3D elasticity corrections for bending and stress analysis of circular/annular composite sandwich plates with auxetic cores, Composite Structures 132 (2015) 175–197.
• [50] M.M. Alipour, M. Shariyat, Analytical layerwise free vibration analysis of circular/annular composite sandwich plates with auxetic cores, International Journal of Mechanical and Materials Engineering 13 (2017) 125–157.
• [51] M. Shariyat, M.M. Alipour, Analytical bending and stress analysis of variable thickness FGM auxetic conical/cylindrical shells with general tractions, Latin American Journal of Solids and Structures 14 (2017) 805–843.
• [52] J. Reddy, An Introduction to the Finite Element Method, 2nd ed., Wiley, New York, 2006.
• [53] A.J.M. Ferreira, Analysis of composite plates using a layerwise theory and multiquadrics discretization, Mechanics of Advanced Materials and Structures 12 (2005) 99–112.
• [54] B. Liu, A.J.M. Ferreira, Y.F. Xing, A.M.A. Neves, Analysis of functionally graded sandwich and laminated shells using a layerwise theory and a differential quadrature finite element method, Composite Structures 136 (2016) 546–553.

Uwagi

PL

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018)