Comparative analysis of testing methods for strength metal-ceramic joint

• Autorzy: Klimek L. , Wołowiec-Korecka Emilia , Pasowska W. , Kula Z.

Identyfikatory

DOI

10.5604/01.3001.0054.3212

• Języki publikacji: EN

Abstrakty

EN

The study aims to perform a comparative analysis of the methods of investigating the strength of a bond between a metal substructure and facing ceramics in the aspect of their application in prosthetic material examinations. The analysis included strength tests determining the binding force between bound materials by means of point shearing, linear shearing, three-point bending and by the roller with a collar method. Design/methodology/approach Co-Cr alloy samples were blasted with 110 μm Al2O3 abrasive at a pressure of 0.25 MPa to develop the surface. The samples were then faced with ceramics. The produced connections were tested for joint strength using the point shear method, linear shear method, pull-out linear shear method, and three-point bending method. The test results were statistically analysed using the ANOVA test (α=0.05). Findings The highest strength was observed in samples subjected to the three-point bending test (M = 57.4 MPa). The lowest strength was observed in the group of samples subjected to the linear pull-out shear method (M = 24.7 MPa). It was shown that there are statistically significant differences between the average strengths in the groups (p<0.05). Research limitations/implications A literature analysis shows that many scientific methods are used to examine the bond between alloys and facing ceramics. However, there is no unequivocal information about the degree to which the test results obtained from different methods are comparable. Practical implications The analysis helps solve some of the research difficulties connected with comparing the results of tests conducted by different authors. Originality/value There is no similar comparative analysis in the literature.

Słowa kluczowe

EN

technology; research; dental materials; metal-ceramic joint

PL

technologia; badania; materiały stomatologiczne; most metalowo-ceramiczny

• Wydawca: International OCSCO World Press
• Czasopismo: Journal of Achievements in Materials and Manufacturing Engineering
• Rocznik: 2023
• Tom: Vol. 121, nr 1
• Strony: 141--150
• Opis fizyczny: Bibliogr. 32 poz., rys., tab.

Twórcy

autor

Klimek L.

• Institute of Materials Science and Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, ul. Stefanowskiego 1/15, 90-537 Łódź, Poland

autor

Wołowiec-Korecka Emilia

• Institute of Materials Science and Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, ul. Stefanowskiego 1/15, 90-537 Łódź, Poland

• https://orcid.org/0000-0003-0978-3948

autor

Pasowska W.

• Department of Dental Technology, Medical University of Lodz, ul. Pomorska 251, 92-213 Łódź, Poland

autor

Kula Z.

• Department of Dental Technology, Medical University of Lodz, ul. Pomorska 251, 92-213 Łódź, Poland

Bibliografia

• [1] T. Ciaputa, A. Ciaputa, Basics of prosthetic work. Permanent work, frame dentures, combined work, Elamed, Katowice, 2005 (in Polish).
• [2] W. Czepułkowska, E. Wołowiec-Korecka, L. Klimek, The role of mechanical, chemical and physical bonds in metal-ceramic bond strength, Archives of Materials Science and Engineering 92/1 (2018) 5-14. DOI: https://doi.org/10.5604/01.3001.0012.5506
• [3] M. Lubas, J. Jasiński, L. Jeziorski, Shear bond strength of ceramic-metal system for the dental applications, Engineering of Biomaterials 12 (2009) 118-121 (in Polish).
• [4] R.M. Joias, R.N. Tango, J.E.J. de Araujo, M.A.J. de Araujo, G.D.S.F.A. Saavedra, T.J.D.A. Paes-Junior, E.T. Kimpara, Shear bond strength of a ceramic to Co-Cr alloys, The Journal of Prosthetic Dentistry 99/1 (2008) 54-59. DOI: https://doi.org/10.1016/S0022-3913(08)60009-8
• [5] C. Sipahi, M. Ozcan, Interfacial shear bond strength between different base metal alloys and five low fusing feldspathic ceramic systems, Dental Materials Journal 31/3 (2012) 333-337. DOI: https://doi.org/10.4012/dmj.2011-143
• [6] K.J. Anusavice (ed), Phillips’ Science of dental materials, 11 th Edition, Saunders, Philadelphia, 2003.
• [7] I. Sulima, The chosen physicochemical aspects if the production of the metal-ceramic joints, Annales Academiae Paedagogicae Cracoviensis 52 (2008) 162-169 (in Polish).
• [8] M. Parchańska-Kowalik, L. Klimek, The influence of chemical processing on the condition of the titanium surface, Inżynieria Materiałowa ‒ Materials Engineering 34/5 (2013) 526-529 (in Polish).
• [9] M. Hajduga, T. Zdziech, The analysis of a structural prosthetic connection ceramics-metal, Current Problems of Biomechanics 2 (2008) 71-78 (in Polish).
• [10] K. Pietnicki, E. Wołowiec, L. Klimek, The effect of abrasive blasting on the strength of a joint between dental porcelain and metal base, Acta of Bioengineering and Biomechanics 16/1 (2014) 63-68. DOI: https://doi.org/10.5277/abb140108
• [11] K. Pietnicki, E. Wołowiec, L. Klimek, Modeling of the number of stubble stuck elements after abrasive jet machining-processing, Archives of Foundry Engineering 11/3 (2011) 51-54.
• [12] K. Pietnicki, Influence of abrasive blasting parameters on the quality of joining dental ceramics with cobalt-chrome alloys, PhD Thesis, Lodz University of Technology, Łódź, 2013 (in Polish).
• [13] M. Wilk, L. Klimek, Oxide layers on titanium obtained by anodization in sulphuric acid, Metal Forming 30/2 (2019) 135-144 (in Polish).
• [14] T. Zdziech, The influence of surface preparation of chrome-nickel and chrome-cobalt alloys on the nature of the structural connection with ceramics, PhD Thesis, Poznan University of Technology, Poznań, 2014 (in Polish).
• [15] M. Parchańska-Kowalik, The influence of surface chemical treatment of titanium on its connection with dental ceramics, PhD Thesis, Medical University of Lodz, Łódź, 2015 (in Polish).
• [16] Z. Kula, Ł. Kołodziejczyk, H. Szymanowski, Influence of the inter-mediate layer on the metal-ceramics bond strength, Engineering of Biomaterials 22/152 (2019) 21-28.
• [17] D. Piestrzyńska, K. Malinowska, A. Kamińska, L. Szalewski, J. Borowicz, Connection between the metal alloys of fixed dentures and veneering materials, Modern Dental Technician 5 (2017) 23-25 (in Polish).
• [18] T. Külünk, M. Kurt, Ç. Ural, Ş. Külünk, S. Baba, Effect of different air-abrasion particles on metal-ceramic bond strength, Journal of Dental Sciences 6/3 (2011) 140-146. DOI: https://doi.org/10.1016/j.jds.2011.05.003
• [19] W. Czepułkowska-Pawlak, Influence of the surface condition after abrasive blasting on the connection of the veneering ceramic with the Ni-Cr alloy framework, PhD Thesis, Lodz University of Technology, Łódź, 2021 (in Polish).
• [20] R. Craig, J. Powers, J. Wataha, Dental materials, Urban and Partner, Wrocław, 2006 (in Polish).
• [21] ISO 9693:2019, Compatibility testing for metal-ceramic and ceramic-ceramic systems, International Organization for Standardization, 2019.
• [22] K. Pietnicki, E. Wołowiec-Korecka, L. Klimek, Modeling strength of the connection the metal substrate to the dental ceramics depending on the parameters of the prior abrasive blasting, Mechanik 8-9 (2015) 266-269. DOI: https://doi.org/10.17814/mechanik.2015.8-9.382
• [23] W. Pasowska, Comparison testing methods of strength connection between Co-Cr alloy with ceramics, MSc Thesis, Medical University of Lodz, Łódź, 2023 (in Polish).
• [24] I. Hammad, Y. Talic, Designs of bond strength tests for metal-ceramic complexes: Review of the literature, The Journal of Prosthetic Dentistry 75/6 (1996) 602-608. DOI: https://doi.org/10.1016/S0022-3913(96)90244-9
• [25] L. Saleeva, R. Kashapov, F. Shakirzyanov, E. Kuznetsov, L. Kashapov, V. Smirnova, N. Kashapov, G. Saleeva, O. Sachenkov, R. Saleev, The Effect of Surface Processing on the Shear Strength of Cobalt-Chromium Dental Alloy and Ceramics, Materials 15/9 (2022) 2987. DOI: https://doi.org/10.3390/ma15092987
• [26] D.-H. Lee, B.-J. Lee, S.-H. Kim, K.-B. Lee, Shear bond strength of porcelain to a new millable alloy and a conventional castable alloy, The Journal of Prosthetic Dentistry 113/4 (2015) 329-335. DOI: https://doi.org/10.1016/j.prosdent.2014.09.016
• [27] K. Sirisha, T. Rambabu, Y. Shankar, P. Ravikumar, Validity of bond strength tests: A critical review: Part I, Journal of Conservative Dentistry and Endodontics 17/4 (2014) 305-311. DOI: https://doi.org/10.4103/0972-0707.136340
• [28] G. Öilo, B. Johansson, M. Syverud, Bond strength of porcelain to dental alloys – an evaluation of two test methods, European Journal of Oral Sciences 89/3 (1981) 289-296. DOI: https://doi.org/10.1111/j.1600-0722.1981.tb01685.x
• [29] F. Watanabe, M. Seto, K. Ueda, M. Ozawa, Fracture force for veneered materials on restorations measured by torsion testing, Dental Materials Journal 37/4 (2018) 592-598. DOI: https://doi.org/10.4012/dmj.2016-432
• [30] Z. Okulus, Preparation and characterization of dental composite materials, PhD Thesis, Poznan University of Technology, Poznań, 2016 (in Polish).
• [31] P. Pietrucha, T. Tański, M. Wiśniowski, Combination of metal with ceramics and material selection in fixed prostheses based on implants, Works of Student Scientific Clubs of the Silesian University of Technology in Gliwice 41 (2015) 57-68 (in Polish).
• [32] M. Wood, G. Thompson, J. Agar, A comparison of debonding strengths of four metal-ceramic systems with and without opaque porcelain, The Journal of Prosthetic Dentistry 97/3 (2007) 141-149. DOI: https://doi.org/10.1016/j.prosdent.2006.12.013