Powiadomienia systemowe
- Sesja wygasła!
- Sesja wygasła!
Tytuł artykułu
Treść / Zawartość
Pełne teksty:
Identyfikatory
Warianty tytułu
Języki publikacji
Abstrakty
The purpose of this article is to investigate the effect of sandblasting surface treatment, before the bonding process, on the strength of the adhesive joints of the three types of aluminium alloy sheets. Three values of pressure were used during the sandblasting process, i.e. 0.41 MPa, 0.51 MPa and 0.56 MPa. After mechanical treatment, the samples of aluminium alloys sheets were degreased three times with acetone by immersion. The elements were bonded with single-lap joints using two components epoxy adhesive. After the curing process, the shear strength tests of the aluminium alloy adhesive joints were conducted, according to the DIN EN 1465 standard. The surface topography of all samples was measured, and the most important surface roughness parameter and its waviness were determined. Based on the experimental results, it was noticed that, among others, while using the same pressure value during sandblasting of different aluminium alloys, the roughness parameters Ra and Rz of the obtained surfaces differed depending on the type of alloy. It is also to notice that more than two times strength of the joints was obtained by those made of the aluminium alloy sheet, which was subjected to heat treatment.
Wydawca
Rocznik
Tom
Strony
262--279
Opis fizyczny
Bibliogr. 62 poz., fig., tab.
Twórcy
autor
- Faculty of Mechanical Engineering, Lublin University of Technology, ul. Nadbystrzycka 36, 20-618 Lublin, Poland
autor
- Faculty of Engineering, Van Lang University, 45 Nguyen Khac Nhu Street, Co Giang Ward, District 1, Ho Chi Minh City, Vietnam
- Faculty of Engineering and Architecture, Ghent University, Jozef Plateaustraat 22,9000 Gent, Zwijnaarde, Belgium
autor
- Faculty of Engineering, Czech University of Life Science Prague, Kamýcká 129, 165 00 Prague, Czech Republic
Bibliografia
- 1. da Silva L.F.M., Carbas R.J.C., Critchlow G.W., Figueiredo M.A.V., Brown K. Effect of material, geometry, surface treatment and environment on the shear strength of single lap joint. International Journal of Adhesion and Adhesives. 2009; 29: 621–632.
- 2. Ebnesajjad S., Ebnesajjad C. Surface Treatment of Materials for Adhesive Bonding. 2nd ed. Inc. Norwich, William Andrew; 2013.
- 3. Adams R.D., Comyn J., Wake W.C. Structural Adhesive Joints in Engineering Book. Springer; 1997.
- 4. Rudawska A. Pressure during curing and the strength of 2024, 2017A and 1050 aluminium alloy sheet adhesive joints. Advances in Science and Technology Research Journal. 2015; 9(26): 96–103.
- 5. de Barros S., Kenedi P.P., Ferreira S.M., Budhe S., Bernardino A.J., Souza L.F.G. Influence of mechanical surface treatment on fatigue life of bonded joints. Journal of Adhesion. 2017; 93: 599–612.
- 6. Rudawska A., Bociąga E., Olewnik-Kruszyńska E. The effect of primers on adhesive properties and strength of adhesive joints made with polyurethane adhesives. Journal of Adhesion Science and Technology. 2017; 31: 327–344.
- 7. Müller M., Valasek P., Rudawska A. Mechanical properties of adhesive bonds reinforced with biological fabric. Journal of Adhesion Science and Technology. 2017; 31: 1859–1871.
- 8. Rudawska A., Wahab M.A. The effect of cataphoretic and powder coatings on the strength and failure modes of EN AW-5754 aluminium alloy adhesive joints. International Journal of Adhesion and Adhesives. 2019; 89: 40–50.
- 9. Prolongo S.G., Ureña A. Effect of surface pre-treatment on the adhesive strength of epoxy-aluminium joints. International Journal of Adhesion and Adhesives. 2009; 29: 23–31.
- 10. Wang, X., Lin J.-p., Min J.-y., Wang P.Ch., Sun, Ch.-ch. Effect of atmospheric pressure plasma treatment on strength of adhesive-bonded aluminum AA5052. Journal of Adhesion. 2018; 94: 701–722.
- 11. Kinloch A.J., Smart N.R. Bonding and failure mechanisms in aluminium alloy adhesive joints. Journal of Adhesion. 1981; 12: 23–35.
- 12. Critchlow G.W., Brewis D.M. Review of surface pretreatments for aluminium alloys. International Journal of Adhesion and Adhesives. 1996; 16: 255–275.
- 13. Spaggiari A.E., Dragoni E. Effect of mechanical surface treatment on the static strength of adhesive lap joints. Journal of Adhesion. 2013; 89: 677–696.
- 14. Lunder O., Lapique F., Johnsen B., Nisancioglu K. Effect of pre-treatment on the durability of epoxy-bonded AA6060 aluminium joints. International Journal of Adhesion and Adhesives. 2004; 24: 107–1170.
- 15. Goglio L. Rezaei M. Effect of different substrate pre-treatments on the resistance of aluminum joints to moist environments. Journal of Adhesion. 2013; 89: 769–784.
- 16. Leena K., Athira K.K., Bhuvaneswari S., Suraj S., Lakshmana Rao, V. Effect of surface pre-treatment on surface characteristic adhesive bond strength of aluminium alloy. International Journal of Adhesion and Adhesives. 2016; 70: 265–270.
- 17. Bhatt R.D., Radhakrishnan V. Evaluation of some machining process as adherend surface treatments in bonding aluminium. Journal of Adhesion Science and Technology. 1989; 3: 383–396.
- 18. Bockenheimer C., Valeske B., Possart W. Network structure in epoxy aluminium bonds after mechanical treatment. International Journal of Adhesion and Adhesives. 2002; 22: 349–356.
- 19. Harris A.F., Beevers A. The effect of grit-blasting on the surface properties for adhesion. International Journal of Adhesion and Adhesives. 1999; 19: 445–452.
- 20. Rudawska A., Danczak I., Müller M., Valasek P. The effect of sandblasting on surface properties for adhesion. International Journal of Adhesion and Adhesives. 2016; 70: 176–190.
- 21. Fondeur F., Koenig J.L. FT-IR characterization of the surface of aluminum as a result of chemical treatment. Journal of Adhesion. 1993; 40: 189–205.
- 22. Wang Y., Chai P., Ma H., Zhang Y. Characteristics and strength of hybrid friction stir welding and adhesive bonding lap joints for AA2024-T3 aluminium alloy. Journal of Adhesion. 2022; 98: 325–347.
- 23. Rudawska A. Adhesive properties, Chapter 7. Scanning Electron Microscope, Ed. V, Kazmiruk, 2012, 101–126, INTECH, Rijeka, Croatia.
- 24. Sancaktar E., Gomatam R. A study on the effects of surface roughness on the strength of single lap joints. Journal of Adhesion Science and Technology. 2001; 15: 97–117.
- 25. Mandolfino Ch., Lertora E., Gambaro C. Effect of surface pretreatment on the performance of adhesive-bonded joints. Key Engineering Materials. 2013; 554–558: 996–1006.
- 26. Rudawska A. Selected aspects of the effect of mechanical treatment on surface roughness and adhesive joint strength of steel sheets. International Journal of Adhesion and Adhesives. 2014; 50: 235–243.
- 27. Rudawska A., Głogowska K., Vitenko T., Stančeková D., Čuboňová N., Kasperek D.: The impact of selected technological and material parameters on the strength of adhesive steel sheets joints. Advances in Science and Technology Research Journal. 2017; 11(2): 8–16.
- 28. Baldan A. Adhesion phenomena in bonded joints. International Journal of Adhesion and Adhesives. 2012; 38: 95–116.
- 29. Akiyama H., Fukata T., Sato T., Horiuchi S., Sato C. Influence of surface contaminants on the adhesion strength of structural adhesives with aluminium. Journal of Adhesion. 2020; 96: 1311–1325.
- 30. Carre A., Schultz J. Polymer-aluminium adhesion. I. The surface energy of aluminium in relation to its surface treatment. Journal of Adhesion. 1983; 15: 151–161.
- 31. Ebnesajjad S. Handbook of Adhesives and Surface Preparation, Chapter 6. Surface Preparation of Metals. Plastic Design Library, Elsevier Inc. 2011, 83–106.
- 32. Rotella G., Alfano M., Schiefer T., Jansen I. Evaluation of mechanical and laser surface pre-treatments on the strength of adhesive bonded steel joints for automotive industry. Journal of Adhesion Science and Technology. 2016; 30: 747–758.
- 33. Rudawska A., Reszka M., Warda T., Miturska I., Szabelski J., Skoczylas A., Stancekova D. Milling as method of surface pretreatment of steel for adhesive bonding. Journal of Adhesion Science and Technology. 2016; 30: 2619–2636.
- 34. Rudawska A. Surface free energy and 7075 aluminium bonded joint strength following degreasing only and without any prior treatment. Journal of Adhesion Science and Technology. 2012; 26: 1233–1247.
- 35. Elbing F., Anagreh N., Dorn L., Uhlmann E. Dry ice blasting as pretreatment of aluminium surfaces to improve the adhesive strength of aluminum bonding joints. International Journal of Adhesion and Adhesives. 2003; 23: 69–79.
- 36. Rechner R., Jansen I., Beyer E. Influence on the strength and aging resistance of aluminium joints by laser pre-treatment and surface modification. International Journal of Adhesion and Adhesives. 2010; 30: 295–601.
- 37. Guo S., Carlson B.E., Hector L.G. Jr., Xia Y., Zhou Q. Increasing strength and fracture toughness of AA7074-T6 adhesively-bonded joints with laser ablation. Journal of Materials Processing Technology. 2018; 259: 368–379.
- 38. Brack N., Rider A.N. The influence of mechanical and chemical treatments on the environmental resistance of epoxy adhesive bonds to titanium. International Journal of Adhesion and Adhesives. 2014; 48: 20–27.
- 39. Takeda T., Yasuoka T., Sugimoto S., Iwahori Y. Strength enhancement of adhesively bonded Ti-6Al-4V alloy joints by flame-based surface treatment. Journal of Adhesion. 2021, DOI: 10.1080/00218464.2020.1870106
- 40. Molitor P., Barron V., Young T. Surface treatment of titanium for adhesive bonding to polymer composites: a review. International Journal of Adhesion and Adhesives. 2001; 21: 129–136.
- 41. Smith T. A surface treatment for Ti-6AI-4V. Journal of Adhesion. 1983; 15: 137–149.
- 42. Kurtovic A., Brandl E., Mertens T., Maier H.J. Laser inducted surface nano-structuring of Ti-6Al-4V for adhesive bonding. International Journal of Adhesion and Adhesives. 2013; 45: 112–117.
- 43. Wahab M.A. Joining composites with adhesives. DEStech Publications Inc; 2016.
- 44. Kim J.G., Choi I., Lee D.G., Seo I.S. Flame and silane treatments for improving the adhesive bonding characteristics of aramid/epoxy composites. Composite Structures 2011; 93: 2696–2705.
- 45. Leone C., Genna S. Effects of surface laser treatment on direct co-bonding strength of CFRP laminates. Composite Structures. 2018; 194: 240–251.
- 46. Xiao G.Z. Effects of solvent on the surface properties of oxygen plasma-treatment polyethylene and olypropylene films. Journal of Adhesion Science and Technology. 1997; 11: 655–663.
- 47. Rudawska A., Nalepa J., Müller M. The effect of degreasing on adhesive joint strength. Advances in Science and Technology Research Journal. 2017; 11(1): 75–81.
- 48. Dodiuk H., Buchman A., Kenig S., Rotel M., Zahavi Reinhart T.J. Preadhesion laser treatment of aluminum surfaces. Journal of Adhesion. 1993; 41: 93–112.
- 49. Comrie R., Affrossman S., Hayward D., Pethrick R.A., Zhou X., Thompson G.E. Ageing of adhesive bonds with various surface treatments, Part 1: Aluminium–dicyandiamide cured epoxy joints. Journal of Adhesion. 2005; 81: 1157–1181.
- 50. Allen K.W., Smith M. A cold chromate etch treatment for some aluminium alloys. Journal of Adhesion. 1985; 18: 111–129.
- 51. Prolongo S.G., Horcajo K.F., Del Rosari G., Ureña A. Strength and Durability of Epoxy-Aluminum Joints. Journal of Adhesion. 2010; 86: 409–429.
- 52. Zhan X., Chen J., Gu Ch., Peng Q., Chen J., Wei Y. Study on effects of pre-treatment and surface roughness on tensile-shear strength of 2060 Al–Li alloy adhesive joints. Journal of Adhesion. 2017; 93: 613–625.
- 53. Boutar Y., Naïmi S., Mezlini S., Ali M.B.S. Effect of surface treatment on the shear strength of aluminium adhesive single-lap joint for automotive applications. International Journal of Adhesion and Adhesives. 2016; 67: 38–43.
- 54. Miturska-Barańska I., Rudawska A., Doluk E. The influence of sandblasting process parameters of aerospace aluminium alloy sheets on adhesive joints strength. Materials. 2021; 14: 6626.
- 55. Xing Y., Yang S., Lu S., Zhang P., An Y., Zhai J. Effect of bonding parameters on compression mechanical properties of bi-directional corrugated honeycomb aluminum. Journal of Adhesion. 2022; 98: 348–366.
- 56. De Barros S., De Souza J.R., Gomes K.C., Sampaio E.M., Barbosa N.P., Torres S.M. Adhesion of geopolymer bonded joints considering surface treatments. Journal of Adhesion. 2012; 88: 364–375.
- 57. Flanagan J., Schütze P., Dunne C., Twomey B., Stanton,K.T. Use of a blast coating process to promote adhesion between aluminium surfaces for the automotive industry. Journal of Adhesion. 2020; 96: 580–601.
- 58. PN-EN 573-3:2019-12. Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products.
- 59. PN-EN 1706. Aluminium i stopy aluminium – Odlewy – Skład chemiczny i własności mechaniczne.
- 60. Folder of Chemical Ciech Grup. Available online at: http://ciechresins.com/files/katalogi/EPIDIAN_CATALOG_PL_PAGE_BY_PAGE.pdf (accessed on 20.12.2021).
- 61. Chemical Ciech Grup. Available online at: http://www.ciechzywice.pl/pl/produkty/chemia-organiczna/zywice/zywice-epoksydowe (accessed on 20.12.2021).
- 62. Available online at: https://www.alumetal-technik. com/scierniwa/elektrokorund-zwykly-brazowy (accessed on 03.11.2021).
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-643277e4-dbca-4bcf-b500-0c258c34e2dc