Preparation of Submicroscale Ag-Coated Cu Particles by Multi-Step Addition of Ag Plating Solution and Antioxidation Properties for Different Ag Shell Thicknesses

• Autorzy: Choi E. B. , Lee J.-H.

Identyfikatory

DOI

10.1515/amm-2017-0166

• Języki publikacji: EN

Abstrakty

EN

For application as a low-cost conductive filler material, submicroscale Cu@Ag particles were fabricated at room temperature without any reductants by a multi-step addition method using an ethylene glycol-based Ag plating solution. Scanning electron microscopy images of the Ag-coated Cu particles demonstrated the formation of discrete Ag particles less than 100 nm in size as well as a thin Ag coating on Cu particles, during the early addition steps. However, as the thickness of the Ag coating increased, the small Ag particles agglomerated into Ag coatings with an increase in the number of Ag plating steps. Owing to the absence of additives such as surfactants, a comparison between the microstructural images and calculations indicated increased agglomeration between fabricated Ag-coated Cu particles with an increase in the number of Ag plating steps. However, thermogravimetric-differential scanning calorimetry of the agglomerated Ag-coated Cu particles after the fifth addition of the Ag plating solution demonstrated their antioxidation behavior even after 70 min in air at 150°C.

Słowa kluczowe

EN

Ag-coated Cu particle; submicrometer; Glycol-based Ag plating solution; mult-step addition; antioxidation

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2017
• Tom: Vol. 62, iss. 2B
• Strony: 1137--1142
• Opis fizyczny: Bibliogr. 18 poz., rys.

Twórcy

autor

Choi E. B.

• Department of Materials Science & Engineering, Seoul National University of Science & Technology, Seoul 139-743, Korea (Republic of)

autor

Lee J.-H.

• Department of Materials Science & Engineering, Seoul National University of Science & Technology, Seoul 139-743, Korea (Republic of)

Bibliografia

• [1] C. Yang, C.P. Wong, M.M.F. Yuen, J. Mater. Chem. C 1, 4052-4069 (2013).
• [2] S.K. Kang, S. Purushothaman, J. Electron. Mater. 28, 1314-1318 (1999).
• [3] M.J. Yim, K.-S. Moon, K.W. Paik, C.P. Wong, J. Adhes. Sci. Technol. 22, 1593-1630 (2008).
• [4] W. Qiao, H. Bao, X. Li, Z. Gu, Int. J. Adhes. Adhes 48, 159-163 (2014)
• [5] H.-M. Ren, Y. Guo, S.-Y. Huang, K. Zhang, M.M.F. Yuen, X.-Z. Fu, S. Yu, R. Sun, C.P. Wong, ACS Appl. Mater. Interfaces 7, 13685-13692 (2015)
• [6] I. Krupa, V. Cecen, A. Boudenne, J. Prokeš, I. Novák, Mater. Des. 51, 620-628 (2013).
• [7] Y.-X. Fu, Z.-X. He, D.-C. Mo, S.-S. Lu, Appl. Therm. Eng. 66, 493-498 (2014).
• [8] B.K. Park, D. Kim, S. Jeong, J. Moon, J.S. Kim, Thin Solid Films 515, 7706-7711 (2007).
• [9] L. Ye, Z. Lai, J. Liu, IEEE Trans. Electron. Packag. Manuf. 22, 299-302 (1999).
• [10] Y. Le, K.-S. Moon, A. Whitman, C.P. Wong, IEEE Trans. Compon. Packag. Technol. 29, 758-763 (2006).
• [11] Y.-S. Eom, K.-S. Choi, S.-H. Moon, J.-H. Park, J.-H. Lee, J.-T. Moon, ETRI J. 33, 864-870 (2011).
• [12] R. Zhang, W. Lin, K. Lawrence, C. P. Wong, Int. J. Adhes. Adhes. 30, 1673-1697 (2008).
• [13] E.B. Choi, J.-H. Lee, J. Alloys Compd. 643, S231-S235 (2015).
• [14] J. Zhao, D. Zhang, J. Zhao, J. Solid State Chem. 184, 2339-2344 (2011).
• [15] X. Xu, X. Luo, H. Zhuang, W. Li, B. Zhang, Mater. Lett. 57, 3987-3991 (2003).
• [16] S.-S. Chee, J.-H. Lee, J. Mater. Chem. C 2, 5372-5381 (2014).
• [17] H.T. Hai, J.G. Ahn, D.J Kim, J.R. Lee, H.S. Chung, C.O. Kim, Surf. Coat. Technol. 201, 3788-3792 (2006).
• [18] Y.-S. Eom, H.-S. Lee, H.-C. Bae, K.-S. Choi, J.-H. Lee, Proceedings of 2015 European Microelectronics Packaging Conference (EMPC) IEEE Friedrichshafen, 1-5 (2015).

Uwagi

PL

Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę (zadania 2017)