Influence of Single-Stage and Duplex Shot Peening on Surface Roughness and Residual Stresses in Al Mg5 Mn1 Sc0,8 Zr0,4 Alloy

• Autorzy: Byczkowska P. , Sawicki J. , Januszewicz B. , Stegliński M.

Identyfikatory

DOI

10.24425/118968

• Języki publikacji: EN

Abstrakty

EN

Conventional shot peening (SP) is cheap surface treatment widely used to enhance fatigue life of mechanical components [3,4]. Basically, it is shooting small particles (shots) on the surface of the sample. However, the process itself is so complex that a lot of companies are not able to optimally employ it due to the amount of parameters that must be controlled all at the same time. The duplex process consists in two stages of shot-peening treatment. The first one consist of shot-peening with spherical cast steel shots or cut wire shots. During the second stage the samples processed in stage one were subject to shot-peening with glass beads. In this work, RSA-501 aluminium alloy was shot peened using shots of different material and diameter and tested using a measurement of residual stresses and surface roughness. Tests and studies conducted so far on RSA-501 aluminium alloy demonstrate that bombardment by a treatment medium in the form of glass beads or shots of various shapes and diameters induces permanent plastic deformation of the surface layer. The roughness achieved after the shot-peening process was determined for each treatment medium. The largest value of Ra parameter was achieved for cut wire shots and this result is consistent with the above-mentioned theoretical knowledge. This medium is the most aggressive one to the surface being treated primarily due to the sharp edges of shots. The duplex process was successful in obtaining higher values of compressive stresses in surface layer than values achievable in conventional single-stage shot peening process.

Słowa kluczowe

EN

shot peening; double shot peening; residual stresses; roughness

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2018
• Tom: Vol. 63, iss. 1
• Strony: 505--511
• Opis fizyczny: Bibliogr. 37 poz., rys., tab.

Twórcy

autor

Byczkowska P.

• Lodz University of Technology, Instutute of Materials Science and Engineering, 1/15 Stefanowskiego Str., 90-924 Lodz, Poland

autor

Sawicki J.

• Lodz University of Technology, Instutute of Materials Science and Engineering, 1/15 Stefanowskiego Str., 90-924 Lodz, Poland

autor

Januszewicz B.

• Lodz University of Technology, Instutute of Materials Science and Engineering, 1/15 Stefanowskiego Str., 90-924 Lodz, Poland

autor

Stegliński M.

• Lodz University of Technology, Instutute of Materials Science and Engineering, 1/15 Stefanowskiego Str., 90-924 Lodz, Poland

Bibliografia

• [1] Ł. Kaczmarek, P. Kula, J. Sawicki, S. Armand, T. Castro, P. Kruszyński, A. Rochel, Arch. Metall. Mater. 54 (4), 1199-1205 (2009).
• [2] Y. K. Gao, Mater. Sci. Eng. 528, 3823-3828 (2011).
• [3] Y. S. Nam, Y. I. Jeong, B. C. Shin, J. H. Byun, Mater. Design. 83, 566-576 (2015).
• [4] I. Černý, J. Sís, D. Mikulová, Surf. Coat. Tech. 243, 20-27 (2014).
• [5] T. Bakalova, N. Petkov, T. Blažek, P. Kejzlar, P. Louda, L. Voleský, Defect. Diffus. Forum 368, 59-63 (2016).
• [6] J. Sawicki, M. Górecki, Ł. Kaczmarek, Z. Gawroński, K. Dybowski, R. Pietrasik, W. Pawlak, Chiang Mai J. Sci. 40 (5), 886-897 (2013).
• [7] Z. Gawroński, J. Sawicki, Mater. Sci. Forum 513, 69-74 (2006).
• [8] N. Petkov, T. Bakalova, T. Cholakova, H. Bahchedzhiev, P. Louda, P. Ryšánek, M. Kormunda M., P. Čapková, P. Kejzlar, Superlattices Microstruct. 109, 402-4 13 (2017).
• [9] J. Capus, Metal Powder Report 68 (6), 12-5 (2013).
• [10] M. Benedetti, V. Fontanari, B.D. Monelli, Procedia Engineer. 2 (1), 397-406 (20 10).
• [11] Y. Fouad, M.E. Metwally, Metall. Mater. Trans. A. 44 (12), 5488-5492 (2013).
• [12] U. Zupanc, J. Grum, J. Mater. Process Tech. 210 (9), 1197-1202 (2010).
• [13] L. Sheng-Li, Y. Cui, X. Gao, T.S. Srivatsan, Mat. Sci. Eng. A-Struct. 574, 243-252 (2013).
• [14] S. Lv, Y. Cu, W. Zhang, X. Tong, T. S. Srivatsan, X. Gao, J. Mater. Eng. Perform. 22 (6), 1735-1743 (2012).
• [15] M. Mhaede, Mater. Design. 41, 61-66 (2012).
• [16] M. Palacios, S. Bagherifard, M. Guagliano I.F. Pariente, Fatigue Fract. Eng. M. 37 (7), 821-82 9 (2014).
• [17] Y. Amano, H. Nanbu, Y. Kameyama, J. Komotori. EPJ Web of Conferences, 6, (2010) DOI: https://doi.org/10.1051/epjconf/20100626011.
• [18] K. Oguri, J. Mater. Process Tech. 211 (8), 1395-1399 (2011).
• [19] J. Vázquez, C. Navarro, J. Domínguez, Int. J. Fatigue, 40, 143-153 (2012).
• [20] L. Wagner, M. Mhaede, M. Wollmann, I. Altenberger, Y. Sano, Int. J. of Struct. Integrity 2 (2), 18 5-199 (2011).
• [21] H. Luong, M.R. Hill, Mat. Sci. Eng. A-Struct. 527 (3), 699-707 (2010).
• [22] G.H. Majzoobi, A.R. Ahmadkhani, Surf. Coat. Tech. 205 (1), 102-109 (2010).
• [23] U. Zupanc, J. Grum, Stroj. Vestn.-J. Mech. E. 57 (05), 379-384 (2011).
• [24] M. Benedetti, V. Fontanari, M. Bandini, E. Savio, Int. J. Fatigue. 70, 451-462 (2015).
• [25] M. Benedetti, V. Fontanari, M. Bandini, D. Taylor, Int. J. Fatigue 61, 271-282 (2014).
• [26] S. Curtis, E. Delosrios, C. Rodopoulos, A. Levers, Int. J. Fatigue 25 (1), 59-66 (2003).
• [27] A. Gariépy, F. Bridier, M. Hoseini, P. Bocher, C. Perron, M. Lévesque, Surf. Coat. Tech. 219, 15-30 (2013).
• [28] M. S. Suh, C. H. Suh, S. H. Nahm, C. M. Suh, Advances in Mechanical Engineering. 7 (1) , 1-10 (2014) DOI: https://doi.org/10.1155/2014/126848.
• [29] M. Benedetti, V. Fontanari, C. Santus, M. Bandini, Int. J. Fatigue 32 (10), 1600-1611 (2010).
• [30] M. Benedetti, V. Fontanari, M. Bandini, Procedia Engineer. 10, 2196-2201 (2011).
• [31] Y.K. Gao, X.R. Wu, Acta Mater. 59 (9), 3737-3747 (2011).
• [32] I. Černý, Procedia Engineer. 10, 3411-3416 (2011).
• [33] K.T. Cho, K. Song, S.H. Oh, Y.K. Lee, K.M. Lim, W.B. Lee, Mat. Sci. Eng. A-Struct. 543, 44-49 (2012).
• [34] L. Trško, M. Guagliano, O. Bokůvka, F, Nový, Procedia Engineer. 74, 246-252 (2014).
• [35] M. Stegliński, P. Byczkowska, J. Sawicki, Ł. Kaczmarek, B. Januszewicz, M. Klich, Arch. Metall. Mater. 61 (2B), 1135-1142 (2016).
• [36] http://www.rsp-technology.com/site-media/user-uploads/rsp_overview_2016-4-1_low.pdf accessed: 28.10.2017
• [37] C. Hamilton, M. Kopyściański, O. Senkov, S. Dymek, Metall. Mater. Trans. A. 44, 1730-1740 (2013).

Uwagi

PL

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).