Research on inner surface of hydroformed tubes

• Autorzy: Ceclan V. A. , Grozav S. D. , Kuric I.

Identyfikatory

DOI

10.12913/22998624/80900

• Języki publikacji: EN

Abstrakty

EN

In this paper a reserch regarding the surfece of hydroforming tubs, made by aluminium and cooper is presented. Tube hydroforming is very important production method considering that metal tubes are widely used in a great variety of engineering products, such as automobile, aircraft, air conditioner, air compressor, exhaust systems, fluid lines. The results show that the surface of tubes it is influence of the hydroforming process. the material of the tube in research of surface is also very important.

Słowa kluczowe

EN

surface; hydroforming; tubes

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2017
• Tom: Vol. 11, no 4
• Strony: 311--317
• Opis fizyczny: Bibliogr. 11 poz., fig., tab.

Twórcy

autor

Ceclan V. A.

• Technical University of Cluj Napoca, Faculty of Machine Building, Blv Muncii 103-105, Cluj Napoca , Romania,

autor

Grozav S. D.

• Technical University of Cluj Napoca, Faculty of Machine Building, Blv Muncii 103-105, Cluj Napoca , Romania

autor

Kuric I.

• University of Žilina, Faculty of Mechanical Engineering, Univerzitna 1, 010 26, Žilina, Slovakia

Bibliografia

• 1.Ceclan V., Grozav S., Sabau E., Popan I.A., Borzan C.,: Structural analysis of tubes hydroforming, AJME-2013, Vol. 11, Issue 4, ISSN 1583–7904, pg. 56–59;
• 2.Sun, ZY , Lang, LH , Li, K ,Wang, Y, Zhang, QD, : Study on the mechanism and the suppression method of wrinkling in side wall using hydroforming of the fairing, INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY Volume: 90 ,Issue: 9–12 Pages: 2527–2535,
• 3.Koç, M. (ed.) Hydroforming for Advanced Manufacturing. Cambridge: Woodhead, 2008.
• 4.Jia, YK ,Li, J , Luo, JB : Analysis and experiment on tube hydroforming in a rectangular cross-sectional die, ADVANCES IN MECHANICAL ENGINEERING Volume: 9 Issue: 5
• 5.Martin RIDZOŇ, Ľubica ELEKOVÁ, Jana LIŠKOVÁ, Jozef BÍLIK: Effect of reduction in three-drawn and two-drawn single-run technology on roughness of inner surface of tubes, 2010, Volume 18, Number 28
• 6.Popan Alexandru, Balc Nicolae, Carean Alexandru, Luca Alina, Miron Alin, :Research to improve the surface roughness of the parts made by water jet milling, AJME-2013, Vol. 11, Issue 2, ISSN 1583–7904, pg. 105–109;
• 7.V. Ceclan, N. Balc, A. Miron, C. Borzan, I.A. Popan, :Numerical simulation of the tube bending process and validation of the results, Academic Journal of Manufacturing Engineering, AJME-2011, Vol. IX, Issue 3, ISSN 1583–7904, pag. 32–37;
• 8.Popan I.A., Balc N., Carean A., Luca A., Miron A.,:Research on Abrasive Water Jet Milling of The Planar Surfaces, Slots and Profiles, ICAMaT 2014 – 7th International Conference on Advanced Manufacturing Technologies, 23–24 October 2014, POLITEHNICA University of Bucharest, Applied Mechanics and Materials Vol 760 (2015) pp 409–414,
• 9.Popan I.A., Balc N., Carean A., Luca A., Miron A.,:Research on Abrasive Water Jet Milling of The Planar Surfaces, Slots and Profiles, ICAMaT 2014 – 7th International Conference on Advanced Manufacturing Technologies, 23–24 October 2014, POLITEHNICA University of Bucharest, Applied Mechanics and Materials Vol 760 (2015) pp 409–414
• 10.P Bella, P Buček, M Ridzoň, M Mojžiš, Ľ Parilák: Numerical simulation of multi-rifled tube drawing – finding proper feedstock dimensions and tool geometry, Materials Science and Engineering 179 (2017) 012008 doi:10.1088/1757–899X/179/1/012008.
• 11.Ridzoň M., (2012), The Effect of Technological Parameters Influencing the Properties of Seamless Cold-Drawn Tubes. – 1. ed. – (Hochschule Anhalt, Köthen). 89 p.

Uwagi

Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę (zadania 2017)