Effect of Cooling Rate on Mechanical Properties of New Multicomponent Fe-Based Amorphous Alloy During Annealing Process

• Autorzy: Rezaei-Shahreza Parisa , Redaei Hossein , Moosavi Parisa , Hasani Saeed , Seifoddini Amir , Jeż Bartłomiej , Nabiałek Marcin

Identyfikatory

DOI

10.24425/amm.2022.137498

• Języki publikacji: EN

Abstrakty

EN

Fe-based bulk metallic glasses (BMGs) have been extensively investigated due to their ultrahigh strength and elastic moduli as well as desire magnetic properties. However, these BMGs have few applications in industrial productions because of their brittleness at room temperature. This study is focused on the effect of cooling rate on the mechanical properties (especially toughness) in the Fe₄₁Co₇Cr₁₅Mo₁₄Y₂C₁₅B₆ BMG. For this aim, two samples with the mentioned composition were fabricated in a water-cooled copper mold with a diameter of 2 mm, and in a graphite mold with a diameter of 3 mm. The formation of crystalline phases of Fe₂₃(B,C)₆, α-Fe and Mo₃Co₃C based on XRD patterns was observed after the partial crystallization process. To determine the toughness of the as-cast and annealed samples, the indentation technique was used. These results revealed that the maximum hardness and toughness were depicted in the sample casted in the water-cooled copper mold and annealed up to 928°C. The reason of it can be attributed to the formation of crystalline clusters in the amorphous matrix of the samples casted in the graphite mold, so that this decrease in the cooling rate causes to changing the chemical composition of the amorphous matrix.

Słowa kluczowe

EN

bulk metallic glasses; BMGs; nanocomposite; mechanical testing; fracture toughness

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2022
• Tom: Vol. 67, iss. 1
• Strony: 251--254
• Opis fizyczny: Bibliogr. 33 poz., fot., rys., tab., wzory

Twórcy

autor

Rezaei-Shahreza Parisa

• Yazd University, Department of Mining and Metallurgical Engineering, 89195-741, Yazd, Iran

• https://orcid.org/0000-0001-9857-9759

autor

Redaei Hossein

• Yazd University, Department of Mining and Metallurgical Engineering, 89195-741, Yazd, Iran

• https://orcid.org/0000-0002-6614-095X

autor

Moosavi Parisa

• Yazd University, Department of Mining and Metallurgical Engineering, 89195-741, Yazd, Iran

• https://orcid.org/0000-0003-3699-7802

autor

Hasani Saeed

• Yazd University, Department of Mining and Metallurgical Engineering, 89195-741, Yazd, Iran

• https://orcid.org/0000-0001-7093-8262

autor

Seifoddini Amir

• Yazd University, Department of Mining and Metallurgical Engineering, 89195-741, Yazd, Iran

• https://orcid.org/0000-0002-6948-7991

autor

Jeż Bartłomiej

• Częstochowa University of Technology, Faculty of Production Engineering and Materials Technology, Department of Physics, 19 Armii Krajowej Av., 42-200 Częstochowa, Poland

• https://orcid.org/0000-0002-7918-5946

autor

Nabiałek Marcin

• Częstochowa University of Technology, Faculty of Production Engineering and Materials Technology, Department of Physics, 19 Armii Krajowej Av., 42-200 Częstochowa, Poland

• https://orcid.org/0000-0001-6585-3918

Bibliografia

• [1] H. Jiang, T. Shang, H. Xian, B. Sun, Q. Zhang, Q. Yu et al., Small Struct. 2000057 (2020).
• [2] W. Yang, Q. Wang, W. Li, L. Xue, H. Liu, J. Zhou et al., Mater. Des. 161, 136-46 (2019).
• [3] L. Liu, C. Zhang, Thin Solid Films 561, 70-86 (2014).
• [4] P. Pietrusiewicz, M. Nabiałek, B. Jeż, Materials (Basel) 13, 4962 (2020).
• [5] M. Nabiałek, B. Jeż, K. Błoch, J. Gondro, K. Jeż, A.V. Sandu, P. Pietrusiewicz, J. Alloys Compd. 820, 153420 (2020)
• [6] W. Guo Y. Wu, J. Zhang, S. Hong, G. Li, G. Ying et al., J. Therm. Spray Technol. 23, 1157-80 (2014).
• [7] B.S. Oliveira, D.H. Milanez, D.R. Leiva, L.I.L. Faria, W.J. Botta, C.S. Kiminami, Mater. Res. 20, 89-95 (2017).
• [8] Y. Han, F.L. Kong, F.F. Han, A. Inoue, S.L. Zhu, E. Shalaan et al. Intermetallics 76, 18-25 (2016).
• [9] A. Hitit, H. Şahin, Metals (Basel) 7, 7 (2016).
• [10] P.H. Tsai, C.I. Lee, S.M. Song, Y.C. Liao, T.H. Li, J.C. Jang et al., Coatings 10, 1212 (2020).
• [11] V. Keryvin, V.H. Hoang, J. Shen, Intermetallics 17, 211-7 (2009).
• [12] J. Zhou, Q. Wang, X. Hui, Q. Zeng, Y. Xiong, K. Yin et al., Mater. Des. 191, 108597 (2020).
• [13] A. Masood, V. Ström, L. Belova, K.V. Rao, J.J. Ågren, Appl. Phys. 113, 013505 (2013).
• [14] S. Zhang, D. Sun, Y. Fu, H. Du, Surf. Coatings Technol. 167, 113-9 (2003).
• [15] Z. Jaafari, A. Seifoddini, S. Hasani, Metall. Mater. Trans. A 50, 2875-85 (2019).
• [16] Z. Dan, Y. Yamada, Y. Zhang, M. Nishijima, N. Hara, H. Matsumoto et al., Mater. Trans. 54, 561-5 (2013).
• [17] A. Makino, H. Men, T. Kubota, K. Yubuta, A. Inoue, J. Appl. Phys. 105, 07A308 (2009).
• [18] S. Wang, W. Jiang, H. Hu, P. Liu, J. Wu, B. Zhang, Prog. Nat. Sci. Mater. Int. 27, 503-6 (2017).
• [19] P. Rezaei-Shahreza, A. Seifoddini, S. Hasani, J. Alloys Compd. 738, 197-205 (2018).
• [20] S. Hasani, P. Rezaei-Shahreza, A. Seifoddini, Metall. Mater. Trans. A 50, 63-71 (2019).
• [21] H. Redaei, P. Rezaei-Shahreza, A. Seifoddini, S. Hasani, Acta Phys. Pol. A 138, 265-7 (2020).
• [22] P. Rezaei-Shahreza, A. Seifoddini, S. Hasani, J. Non-Crystalline Solids 471, 286-294 (2017).
• [23] P. Rezaei-Shahreza, A. Seifoddini, S. Hasani, Thermochimica Acta 652, 119-125 (2017).
• [24] S. Hasani, P. Rezaei-Shahreza, A. Seifoddini, Thermal Analysis and Calorimetry 143, 3365-3375 (2021).
• [25] P. Scherrer, Bestimmung der inneren Struktur und der Größe von Kolloidteilchen mittels Röntgenstrahlen. Kolloidchem. Ein Lehrb., Berlin, Heidelberg: Springer Berlin Heidelberg, 387-409 (1912).
• [26] T. Gloriant, M. Gich, S. Suriñach, M.D. Baró, A.L. Greer, J. Metastable Nanocrystalline Mater. 8, 365-70 (2000).
• [27] S. Cardinal, J.M. Pelletier, M. Eisenbart, U.E. Klotz, Mater. Sci. Eng. A 660, 158-65 (2016).
• [28] S. Enzo, S. Polizzi, A. Benedetti, Zeitschrift Für Krist 170, 275-87 (1985).
• [29] V. Keryvin, X.D. Vu, V.H. Hoang, J. Shen, J. Alloys Compd. 504, S41-4 (2010).
• [30] H.W. Zhang, G. Subhash, X.N. Jing, L.J. Kecskes, R.J. Dowding, Philos. Mag. Lett. 86, 333-45 (2006).
• [31] G.R. Antist, P. Chantikul, B.R. Lawn, D.B. Marshall, J. Am. Ceram. Soc. 64, 533-8 (1981).
• [32] Y. He, G.J. Shiflet, S.J. Poon, Acta Metall. Mater. 43, 83-91 (1995).
• [33] C. Suryanarayana, Mater. Today 15, 486-98 (2012).

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2024).