An analysis of centrifugal MQL supply system potential in the internal cylindrical grinding process

• Autorzy: Nadolny K. , Wojtewicz M. , Sienicki W. , Herman D.

Identyfikatory

DOI

10.1016/j.acme.2014.08.009

• Języki publikacji: EN

Abstrakty

EN

In the article the state of knowledge regarding the functions and supply methods of the cooling liquid into the grinding zone were presented. The new system for centrifugal supply of oil mist was described. The results of experimental investigations conducted into the internal cylindrical grinding process were given. The life of the wheel, machined surface roughness, grinding power and temperature in the machining zone were analyzed. Experimental results showed that compared to flood cooling, this new system provides double the lifespan of the wheel, significantly reducing the volume of wheel wear and enabling the slightly reduced roughness of machined surface and grinding power. Using a new coolant supply method caused an increase in the workpiece temperature, compared to the flood cooling.

Słowa kluczowe

EN

MQL; internal cylindrical grinding; flood cooling; wheel life; surface roughness parameters

PL

szlifowanie cylindryczne; obróbka skrawaniem; chłodzenie

• Wydawca: Springer ; Wrocław University of Science and Technology
• Czasopismo: Archives of Civil and Mechanical Engineering
• Rocznik: 2015
• Tom: Vol. 15, no. 3
• Strony: 639--649
• Opis fizyczny: Bibliogr. 22 poz., rys., tab., wykr.

Twórcy

autor

Nadolny K.

• Department of Production Engineering, Faculty of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17, 75-620 Koszalin, Poland

autor

Wojtewicz M.

• Subject Group of Applied Chemistry, Faculty of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17, 75-620 Koszalin, Poland

autor

Sienicki W.

• Subject Group of Applied Chemistry, Faculty of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17, 75-620 Koszalin, Poland

autor

Herman D.

• Division of Materials Science and Ceramics, Institute of Technology and Education, Koszalin University of Technology, Śniadeckich 2, 75-453 Koszalin, Poland

Bibliografia

• [1] B. Shen, A.J. Shih, Minimum quantity lubrication (MQL) grinding using vitrified CBN wheels, Transactions of NAMRI/ SME 37 (2009) 129–136.
• [2] F. Klocke, Manufacturing Processes. 2. Grinding, Honing, Lapping, Springer-Verlag, Berlin, 2009.
• [3] I.D. Marinescu, M. Hitchiner, E. Uhlmann, W.B. Rowe, I. Inasaki, Handbook of Machining with Grinding Wheels, CRC Press, Boca Raton, 2007.
• [4] W.B. Rowe, Principles of Modern Grinding Technology, William Andrew, Burlington, 2009.
• [5] R. Wojcik, Application of new kinds of cooling media and supplying methods during surface grinding,(Nowe media i sposoby ich doprowadzania do strefy szlifowania), Archives of Mechanical Technology and Automation 28 (4) (2008) 137–145.
• [6] F. Klocke, A. Baus, T. Beck, Coolant induced forces in CBN high speed grinding with shoe nozzles, Annals of the CIRP 49 (1) (2000) 241–244.
• [7] J. Webster, E. Brinksmeier, C. Heinzel, M. Wittmann, K. Thoens, Assessment of grinding fluid effectiveness in continuous-dress creep feed grinding, Annals of the CIRP 51 (1) (2002) 235–240.
• [8] S. Saji, V. Radhakrishnan, An investigation on surface grinding using graphite as lubricant, International Journal of Machine Tools & Manufacture 42 (2002) 733–740.
• [9] J. Webster, Selection of coolant type and application technique in grinding, in: Supergrind 1995 – Grinding and Polishing with Superabrasives, Connecticut, USA, November 2–3, (1995), pp. 205–220.
• [10] E. Brinksmeier, T. Brockhoff, A. Walter, Minimum quantity lubrication in grinding, in: Proceedings of the Second International Machining and Grinding Conference, SME, MI, USA, September 8–11, (1997), pp. 639–654.
• [11] E. Brinksmeier, T. Brockhoff, A. Walter, Minimalmengenku- ehlschmierung und Trochenbearbeitung beim Schleifen, Haerterein-Technische Mitteilungen 52 (1997) 166–170.
• [12] E. Brinksmeier, C. Heinzel, M. Wittmann, Friction, cooling and lubrication in grinding, CIRP Annals: Manufacturing Technology 48 (2) (1999) 581–598.
• [13] T. Karpinski, J. Sieniawski, Ecological methods of cooling in grinding processes, Archives of Civil and Mechanical Engineering 2 (1/2) (2002) 73–81.
• [14] M.Y. Tsai, S.X. Jian, Development of a micro-graphite impregnated grinding wheel, International Journal of Machine Tools & Manufacture 56 (2012) 94–101.
• [15] M. Alberts, K. Kalaitzidou, S. Melkote, An investigation of graphite nanoplatelets as lubricant in grinding, International Journal of Machine Tools & Manufacture 49 (2009) 966–970.
• [16] K. Nadolny, W. Kapłonek, M. Wojtewicz, W. Sienicki, The assessment of sulfurization influence on cutting ability of the grinding wheels in internal cylindrical grinding of Titanium Grade 2, Indian Journal of Engineering & Materials Sciences 20 (2) (2013) 108–124.
• [17] W. Kaplonek, K. Nadolny, The diagnostics of abrasive tools after internal cylindrical grinding of hard-to-cut materials by means of a laser technique using imaging and analysis of scattered light, Arabian Journal for Science and Engineering 38 (4) (2013) 953–970.
• [18] Norton Company (USA), The Norton Full Line of Stock Abrasive Products, 2011 http://hpmvideo.saint-gobain.com/ wsi-ab-sga-na/eMagCatalogs/NortonIndustrial/2011/pdf/ NortonIndustrial-Catalog7362-2011.pdf (accessed 19.10.11).
• [19] Super Abrasives (India), Range of Products – Internal Grinding Wheels, 2014 http://www.superabrasivesindia.com/internal. htm (accessed 14.04.14).
• [20] Systec Segments (USA), Sulfur Treatment, 2014 http://www. systecsegments.com/faq3.htm#15 (accessed 14.04.14).
• [21] M.L. Harmann, Abrasive article, US Patent 1615271 (1927).
• [22] K. Nadolny, W. Sienicki, M. Wojtewicz, The effect upon the grinding wheel active surface condition when impregnating with non-metallic elements during internal cylindrical grinding of titanium, Archives of Civil and Mechanical Engineering (2014), http://dx.doi.org/10.1016/j.acme.2014.03. 004.