Time Distribution Analysis of 3D Prints with the Use of a Filament and Masked Stereolithography Resin 3D Printer

• Autorzy: Paśnikowska-Łukaszuk Magdalena , Korulczyk Katarzyna , Kapłon Kamil , Urzędowski Arkadiusz , Wlazło-Ćwiklińska Magda

Identyfikatory

DOI

10.12913/22998624/154926

• Języki publikacji: EN

Abstrakty

EN

The article focuses on the subject of 3D printing. 3D printing technology and currently used solutions are described. The materials used in printing with the use of a filament printer and a resin printer are discussed. The fused deposiotion modeling technique and the LCD-based stereolithography. Printing technology were presented. Samples were prepared using 3D modeling software. The software used to make the models is discussed. The designed models were printed on two types of printers, using different model orientations. Printouts were measured several times. The obtained data was analyzed and the conclusions, proposed solutions and possible improvements to 3D printing were presented at the end. The article deals with the subject of the possibility of accelerating 3D prints due to their location, but also the influence of warming up the printer during subsequent prints was checked.

Słowa kluczowe

EN

3D printing; polylactic acid; fused deposition modeling; stereolithography; masked stereolithography; resin printing

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2022
• Tom: Vol. 16, no 5
• Strony: 242--249
• Opis fizyczny: Bibliogr. 16 poz., fig., tab.

Twórcy

autor

Paśnikowska-Łukaszuk Magdalena

• Faculty of Technology Fundamentals, Lublin University of Technology, ul. Nadbystrzycka 38, 20-618 Lublin, Poland

• https://orcid.org/0000-0002-3479-6188

autor

Korulczyk Katarzyna

• Faculty of Technology Fundamentals, Lublin University of Technology, ul. Nadbystrzycka 38, 20-618 Lublin, Poland

autor

Kapłon Kamil

• Faculty of Technology Fundamentals, Lublin University of Technology, ul. Nadbystrzycka 38, 20-618 Lublin, Poland

autor

Urzędowski Arkadiusz

• Faculty of Technology Fundamentals, Lublin University of Technology, ul. Nadbystrzycka 38, 20-618 Lublin, Poland

• https://orcid.org/0000-0002-0440-3013

autor

Wlazło-Ćwiklińska Magda

• Faculty of Technology Fundamentals, Lublin University of Technology, ul. Nadbystrzycka 38, 20-618 Lublin, Poland

• https://orcid.org/0000-0002-0086-2319

Bibliografia

• 1. Siemiński P., Budzik G. Additive techniques: 3D printing. Oficyna Wydawnicza Politechniki Warszawskiej, 2015. (in Polish).
• 2. Tatarczak J. Overview of modern 3D printing technologies of metal objects. Mechanik, 2017, 7: 612-614. (in Polish).
• 3. Szulżyk-Cieplak J., Duda A., Sidor, B. 3D printers–new possibilities in education. Advances in Science and Technology Research Journal, 8(24), 96-101., 2014.
• 4. Micht D., Kaczmarska B, Gierulski W.,Szmidt A. The universality of 3D printing in FDM technology. Politechnika Świętokrzyska, 2017. (in Polish).
• 5. Urzędowski A., Paśnikowska-Łukaszuk M, Kapłon K. The use of the 3D modeling process and 3D printing in the preparation of entities supporting motor skills and sensory development, Wspomaganie komputerowe w dydaktyce, Wydawnictwo Politechniki Lubelskiej, 2021, (in Polish).
• 6. Hespel A. M., Wilhite R., Hudson J. Invited review applications for 3d printers in veterinary medicine. Veterinary Radiology & Ultrasound, 55(4), 347-358, 2014.
• 7. Zgryza Ł., Raczyńska A., Paśnikowska-Łukaszuk M. Thermovisual measurements of 3D printing of ABS and PLA filaments. Advances in Science and Technology Research Journal, 12(3), 2018.
• 8. Liu Z., Wang Y., Wu B., Cui C., Guo Y., Yan C. A critical review of fused deposition modeling 3D printing technology in manufacturing polylactic acid parts. The International Journal of Advanced Manufacturing Technology, 102(9), 2877-2889., 2019.
• 9. Zaburko J., Urzędowski A., Szulżyk-Cieplak J., Trník A., Suchorab Z., Łagód, G. Analysis of thermal operating conditions of 3D printers with printing chamber. AIP Conference Proceedings (Vol. 2429, No. 1, p. 020020). AIP Publishing LLC 2021.
• 10. Rengevič A., Fúra M., Čuboňová N. Analysis of printing parameters for production of components with Easy3DMaker printer. Advances in Science and Technology. Research Journal, 10(32). 2016.
• 11. Korga S., Barszcz M., Dziedzic K. Development of software for identification of filaments used in 3d printing technology. Applied Computer Science, 15(1), 74-83., 2019.
• 12. Barszcz M., Montusiewicz J., Paśnikowska-Łukaszuk M., Sałamacha A. Comparative analysis of digital models of objects of cultural heritage obtained by the “3D SLS” and “SfM” methods. Applied Sciences, 11(12), 5321. 2021.
• 13. Mazzanti V., Malagutti L., Mollica F. FDM 3D Printing of Polymers Containing Natural Fillers: A Review of their Mechanical Properties. Polymers 2019, 11, 1094.
• 14. Ćwikła G., et al. The influence of printing parameters on selected mechanical properties of FDM/FFF 3D-printed parts. IOP conference series: materials science and engineering. Vol. 227. No. 1. IOP Publishing, 2017.
• 15. Wang Jie, et al. Stereolithographic (SLA) 3D printing of oral modified-release dosage forms. International journal of pharmaceutics 503.1-2 (2016): 207-212.
• 16. Sotov A., et al. LCD-SLA 3D printing of BaTiO3 piezoelectric ceramics. Ceramics International 47.21 (2021): 30358-30366.

Uwagi

Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023).