The Influence of the Use of Fasteners with Different Stiffness in Hybrid Joints Subjected to Complex Mechanical Loads

• Autorzy: Sadowski T. , Nowicki M. , Golewski P.

Identyfikatory

DOI

10.24425/amm.2019.130089

• Języki publikacji: EN

Abstrakty

EN

To this day, most of the papers related to hybrid joints were focused on single and double lap joints in which shear deformation and degradation was the dominant phenomenon. However, in real constructions, complex state of loads can be created by: a) torsion with shear, b) bending with shear, c) torsion with tensile. Analytical and numerical computation for simple mechanical joints is known, however, the introduction of an adhesive layer to this joint makes the load transferred both through: (1) the adhesive and (2) mechanical fasteners. There is also an interaction between the amount and stiffness of mechanical fasteners and the strength of the adhesive layer. The paper presents the results of numerical calculations for the bending with shear type of load for the hybrid structural joint and corresponding simple joints by: (1) pure adhesion and (2) rivets with different quantity maintaining the same cross-sectional area. A total of 9 simulations were performed for: (1) 4 types of pure rivets connections, (2) pure adhesive joint and (3) 4 kinds of hybrid joints. The surface-based cohesive behavior was used for creation of the adhesive layer, whereas the rivets were modelled by connector type fasteners, which simplify complexity of the numerical model. The use of connectors allowed for effort assessment taking into account damage in both types of connections. Application of connector elements can be useful for larger structures modelling, e.g. aircraft fuselage, where the number of mechanical joints is significant and complex load conditions occur.

Słowa kluczowe

EN

hybrid joining; fasteners; adhesive; mechanical loads; numerical modelling

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2019
• Tom: Vol. 64, iss. 4
• Strony: 1263--1268
• Opis fizyczny: Bibliogr. 44 poz., rys., tab.

Twórcy

autor

Sadowski T.

• Lublin University of Technology, Department of Solid Mechanics, 40 Nadbystrzycka Str., 20-618 Lublin, Poland

autor

Nowicki M.

• Lublin University of Technology, Department of Solid Mechanics, 40 Nadbystrzycka Str., 20-618 Lublin, Poland

autor

Golewski P.

• Lublin University of Technology, Department of Solid Mechanics, 40 Nadbystrzycka Str., 20-618 Lublin, Poland

Bibliografia

• [1] E. F. Karachalios, R. D. Adams, L.F.M. da Silva, Int. Jour. of Adh. & Adh. 45, 69-76 (2013).
• [2] L.D.R. Grant, R. D. Adams, L.F.M. da Silva, Int. Jour. of Adh. & Adh. 29, 535-542 (2009).
• [3] E. F. Karachalios, R. D. Adams, L.F.M. da Silva, Int. Jour. of Adh. & Adh. 43, 81-95 (2013).
• [4] E. F. Karachalios, R. D. Adams, L.F.M. da Silva, Int. Jour. of Adh. & Adh. 43, 96-108 (2013).
• [5] E. F. Karachalios, R. D. Adams, L.F.M. da Silva, Jour. of Adh. Sci. and Tech. 27, 1811-1827 (2013).
• [6] F. Moroni, A. Pirondi, C. Pernechele, A. Gaita, L. Vescovi, Frac. and Struc. Int. 47, 294-302 (2019).
• [7] F. Moroni and A. Pirondi, Adv. Struct. Mat. 6, 79-108 (2011).
• [8] T. Sadowski, P. Golewski, Key Eng. Mater. 607, 49-54 (2014).
• [9] T. Sadowski, P. Golewski, Arch. of Metall. and Mater. 58, 581-587 (2013).
• [10] P. Golewski, T. Sadowski, Int. Jour. of Adh. and Adh. 77, 174-182 (2017).
• [11] T. Sadowski, M. Nowicki, D. Pietras, P. Golewski. Inter. Jour. of Adh. and Adh., 89, 72-81 (2019).
• [12] T. Sadowski, P. Golewski, M. Kneć, Comp. Struc. 112, 66-77 (2014).
• [13] T. Sadowski, M. Kneć, P. Golewski, (2014) Key Eng. Mater. 601, 25-28 (2014).
• [14] T. Balawender, T. Sadowski, P. Golewski, Comp. Mat. Sc. 64, 270-272 (2012).
• [15] T. Sadowski, T. Balawender, Adv. Struct. Mat. 6, 149-176 (2011).
• [16] T. Sadowski, P. Golewski, V. Radoiu, Solid State Phen. 254, 1-7 (2016).
• [17] P. Golewski, T. Sadowski, IOP Conf. Ser.: Mater. Sci. Eng. 416, 1-6 (2018).
• [18] P. Lacki, A. Derlatka, Comp. Struct. 159, 491-497 (2017).
• [19] P. Lacki, K. Adamus, Comp. and Struc. 89, 977-985 (2011).
• [20] P. Lacki, J. Niemiro, Comp. Struc. 159, 538-547 (2017).
• [21] K. Adamus, J. Adamus, J. Lacki, Comp. Struc. 202, 95-101 (2018).
• [22] P. Lacki, A. Derlatka, Comp. Struc. 202, 201-209 (2018).
• [23] P. Lacki, J. Nawrot, A. Derlatka, J. Winowiecka, Comp. Struc. 211, 244-253 (2019).
• [24] T. Balawender, Acta Metall. Slov. 24, 1, 58-64 (2018).
• [25] J. Cao, J.L. Grenestedt, Comp. Part A 35, 1091-1105 (2004).
• [26] M. P. Cavatorta, D. S. Paolino, L. Peroni, M. Rodino, Comp. Part A 38, 1251-1261 (2007).
• [27] J. P. Kabche, V. Caccese, K. A. Berube, R. Bragg, Comp. Part B 38, 66-78 (2007).
• [28] V. Caccese, J. P. Kabche, K. A. Berube, Comp. Struct. 81, 450-462 (2007).
• [29] Z. Kapidzic, L. Nilsson, H. Ansell, Comp. Struct. 109, 198-210 (2014).
• [30] K. Zhang, D. Shi, W. Wang, Q. Wang, Comp. Struct. 160, 1198-1204 (2017).
• [31] J. H. Oh, Comp. Sci. and Tech. 67, 1340-1347 (2007).
• [32] T. Sadowski, M. Nowicki. IOP Conf. Ser.: Mater. Sci. Eng. 416, 1-7 (2018).
• [33] A. Pirondi, D. Fersini, E. Perotti, F. Moroni. Atti del Congresso IGF, 19, 85-93 (2007).
• [34] T. Sadowski, L. Marsavina, Comput. Mater. Sci. 50, 1336-1346 (2011).
• [35] T. Sadowski, Comput. Mater. Sci. 64, 209-211 (2012).
• [36] V. Burlayenko, H. Altenbach, T. Sadowski, S. D. Dimitrova, Comput. Mater. Sci. 116, 11-21 (2016).
• [37] T. Sadowski, L. Marsavina, N. Peride, E. M. Craciun, Comput. Mat. Sci. 46, 687-693 (2009).
• [38] T. Sadowski, J. Bęc, Comput. Mat. Sci. 50, 1269-1275 (2011).
• [39] H. Dębski, T. Sadowski, Comput. Mater. Sci. 83, 403-411 (2014).
• [40] J. Gajewski, T. Sadowski, Comput. Mat. Sci. 82, 114-117 (2014).
• [41] M. Birsan, T. Sadowski, L. Marsavina, D. Pietras, Int. J. Solids Struct. 50, 519-530 (2013).
• [42] G. Golewski, T. Sadowski, Const & Build. Mat. 51, 207-214 (2014).
• [43] T. Sadowski, Mech. Mat. 18, 1-16 (1994).
• [44] V. Burlayenko, T. Sadowski, Comput. Mat. Sci. 52, 212-216 (2012).

Uwagi

EN

1. This work was financially supported by Ministry of Science and Higher Education (Poland) within the statutory research number S/20/2019.

PL

2. Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2019).