Experimental investigation of cryogenically treated HSS tool in turning on AISI1045 using fuzzy logic – Taguchi approach

• Autorzy: Raja P. , Malayalamurthi R. , Sakthivel M.

Identyfikatory

DOI

10.24425/bpasts.2019.130178

• Języki publikacji: EN

Abstrakty

EN

This work depicts the effects of deep cryogenically treated high-speed steel on machining. In recent research, cryogenic treatment has been acknowledged for improving the life or performance of tool materials. Hence, tool materials such as the molybdenum-based high-speed tool steel are frequently used in the industry at present. Therefore, it is necessary to observe the tool performance in machining; the present research used medium carbon steel (AISI 1045) under dry turning based on the L9 orthogonal array. The effect of untreated and deep cryogenically treated tools on the turning of medium carbon steel is analyzed using the multi-input-multi-output fuzzy inference system with the Taguchi approach. The cutting speed, feed rate and depth of cut were the selected process parameters with an effect on surface roughness and the cutting tool edge temperature was also observed. The results reveal that surface roughness decreases and cutting tool edge temperature increases on increasing the cutting speed. This is followed by the feed rate and depth of cut. The deep cryogenically treated tool caused a reduction in surface roughness of about 11% while the cutting tool edge temperature reduction was about 23.76% higher than for an untreated tool. It was thus proved that the deep cryogenically treated tool achieved better performance on selected levels of the turning parameters.

Słowa kluczowe

EN

cryogenic; fuzzy; roughness; Taguchi; temperature; turning

• Wydawca: Polska Akademia Nauk, Wydział IV Nauk Technicznych
• Czasopismo: Bulletin of the Polish Academy of Sciences. Technical Sciences
• Rocznik: 2019
• Tom: Vol. 67, nr 4
• Strony: 687--696
• Opis fizyczny: Bibliogr. 39 poz., rys., tab.

Twórcy

autor

Raja P.

• Faculty of Mechanical Engineering, Adhiyamaan College of Engineering, Anna University, Chennai, Tamil Nadu, India

autor

Malayalamurthi R.

• Faculty of Mechanical Engineering, A C Government College of Engineering and Technology, Karaikudi, Tamil Nadu, India

autor

Sakthivel M.

• Faculty of Mechanical Engineering, Adhiyamaan College of Engineering, Chennai, Tamil Nadu, India

Bibliografia

• [1] F.J. Silva, S.D. Franco, Á.R. Machado, E.O. Ezugwu, and A.M. Souza, “Performance of cryogenically treated HSS toolsˮ, Wear 261, 674–685 (2006).
• [2] T. Kivak and U. Seker, “Effect of cryogenic treatment applied to M42 HSS drills on the machinability of Ti-6Al-4V alloyˮ, Mater.Technol. 49(6), 949–956 (2015).
• [3] S.S. Gill et al., “Flank Wear and Machining Performance of Cryogenically Treated Tungsten Carbide Insertsˮ, Mater.Manuf.Process. 26, 1430–1441 (2011).
• [4] N.S. Kalsi, R. Sehgal, and V.S. Sharma, “Cryogenic Treatment of Tool Materials: A Reviewˮ, Mater.Manuf.Process. 25(10), 1077–1100 (2010).
• [5] S. Singh, S. Singh, and J. Singh, “Improvement in Tool Life of M2 HSS Tools by Cryogenic Treatmentˮ, J.Metall.Eng. 1(2), 47–61 (2011).
• [6] S.S. Gill, “Machining Performance of Cryogenically Treated AISI M2 High Speed Steel Toolsˮ, J.Eng.Res.Stud. 3(2), 45–49 (2012).
• [7] L.P. Singh and J. Singh, “Effects of Cryogenic Treatment on High-speed Steel Toolsˮ, J. Eng.Technol. 1(2), 88–93 (2011).
• [8] T.V.S. Reddy, T. Sornakumar, M.V. Reddy, R. Venkatram, and A. Senthilkumar, “Turning studies of deep cryogenic treated P-40 tungsten carbide cutting tool inserts – technical communicationˮ, Mach.Sci.Technol. 13, 269–281(2009).
• [9] S. Singh, J. Singh, H. Singh, and R. Singh, “Investigation on wear behaviour of cryogenically treated TiAlN coated tungsten carbide inserts in turningˮ, Int.J.Mach.ToolsManuf, 51(1), 25–33 (2011).
• [10] L. Shakeel Ahmed and M. Pradeep Kumar, “Multiresponse optimization of cryogenic drilling on Ti-6Al-4V alloy using topsis methodˮ, J.Mech.Sci.Technol. 30 (4), 1835–1841(2016).
• [11] S. Vinoth Kumar and M. Pradeep Kumar, “Experimental inves-tigation of the process parameters in cryogenic cooled electrode in EDMˮ, J.Mech.Sci.Technol. 29 (9), 3865–3871(2015).
• [12] M. Dhananchezian, M.P. Kumar, and T. Sornakumar, “Cryogenic Turning of AISI 304 Stainless Steel with Modified Tungsten Carbide Tool Insertsˮ, MaterialsandManufacturingProcesses, 26(5), 781‒785 (2011)
• [13] L.S. Ahmed and M.P. Kumar, “Cryogenic Drilling of Ti-6Al-4V Alloy Under Liquid Nitrogen Coolingˮ, Mater.Manuf.Process.31(7), 951–959 (2016).
• [14] L.S. Ahmed and M.P. Kumar, “Investigation of cryogenic cool-ing effect in reaming Ti-6AL-4V alloyˮ, Mater.Manuf.Process.32(9), 970–978 (2016).
• [15] H. Gökkaya and İ. Uygur, “ The effects of cryogenic-treated carbide tools on tool wear and surface roughness of turning of Hastelloy C22 based on Taguchi methodˮ, Int.J.Adv.Manuf.Technol. 82(1–4), 303–314 (2015).
• [16] R. Gessing, “Whether the opinion about superiority of fuzzy con-trollers is justified”, Bull.Pol.Ac.:Tech. 58(1), 59–65 (2010).
• [17] Timothy J. Ross, Fuzzy logic with engineering applications, 3rd ed., pp.14‒145, John Wiley & Sons, United Kingdom, 2010.
• [18] J. Jantzen, Foundation sof fuzzy control: apractical approach, 2nd ed., pp.1‒83, John Wiley & Sons, United Kingdom, 2013.
• [19] L.A. Zadeh, “Fuzzy Setsˮ, Information and control. 8(3), pp.338‒353(1965).
• [20] K. Abhishek et al., “Taguchi approach followed by fuzzy linguistic reasoning for quality-productivity optimization in machining operation A case studyˮ, J.Manuf.Technol.Manage. 24(6), 929–951(2012).
• [21] S.S. Gill et al., “Adaptive neuro-fuzzy inference system modeling of cryogenically treated AISI M2 HSS turning tool for estimation of flank wearˮ, Expert.Syst.Appl. 39(4), 4171–4180(2012).
• [22] R. Autay, M. Kchaou, and F. Dammak, “Experimental investigation of the tribological behaviour of carbon and low-alloy steels sliding against HSSˮ, Mech.Ind.16(1), 109 (2015).
• [23] E. M. Trent, P. K. Wright, Metal Cutting, 4th ed., pp.138‒142, Butterworth–Heinemann, New York, USA, 2000.
• [24] S. Akincioğlu, H. Gökkaya, and İ. Uygur, “A review of cryogenic treatment on cutting toolsˮ, Int.J.Adv.Manuf.Technol.78(9–12), 1609–1627 (2015).
• [25] H.M. T. Production technology, pp.98, Tata McGraw-Hill, New Delhi, India, 2004.
• [26] D. Tanikić et al., “Application of response surface methodology and fuzzy logic based system for determining metal cutting temperatureˮ, Bull.Pol. Ac.: Tech. 64(2), 435–445 (2016).
• [27] M. Sakthivel, S. Vijayakumar and M.P. Jenarthanan, “Grey-fuzzy logic to optimise process parameters in drilling of glass fibre reinforced stainless steel mesh polymer compositeˮ, Pigment & Resin Technology, 46(4), 276–285 (2017).
• [28] G. Taguchi, E.A. Elsayed, and T. Hsiang, Quality Engineeringin Production Systems, 2nd ed., pp.11‒58, McGraw-Hill, New York, 1989.
• [29] C.L. Lin, J.L. Lin, and T.C. Ko, “Optimisation of the EDM Process Based on the Orthogonal Array with Fuzzy Logic and Grey Relational Analysis Methodˮ, Int. J. Adv. Manuf. Technol. 19, 271–277(2002).
• [30] A. Khan and K. Maity, “Comparative study of some machinability aspects in turning of pure titanium with untreated and cryogenically treated carbide insertsˮ, Journal of Manufacturing Processes, 28, 272‒289 (2017).
• [31] R. Jithin Babu and A. Ramesh Babu, “Correlation among the cutting parameters, surface roughness and cutting forces in turning process by experimental Studiesˮ, All India Manufacturing Technology, Design and Research Conference, IIT Assam, India, 12–14 (2014).
• [32] K.C. Jain and A.K. Chitale, Text Book of Production Engineering, 2nd ed., pp.79‒96, PHI, New Delhi, India, 2010.
• [33] T. Sandy, H. Wang, and W.B. Lee, “Materials Characterisation and Mechanism of Micro-Cutting in Ultra-Precision Diamond Turningˮ, Springer-Verlag Berlin Heidelberg, Germany, (2017).
• [34] T.V. Kumar, R. Thirumurugan, and B. Viswanath, “Influence of cryogenic treatment on the metallurgy of ferrous alloys: A reviewˮ, Mater. Manuf. Process. 32(16), 863–867 (2017).
• [35] F.H. Çakir and O.N. Çelik, “The effects of cryogenic treatment on the Toughness and Tribological Behaviors of Eutectoid Steel. Journal of Mechanical Science and Technology, 31(7 ), 3233–3239(2017).
• [36] D.N. Korade, K.V. Ramana, K.R. Jagtap, and N.B. Dhokey, “Effect of Deep Cryogenic Treatment on Tribological Behaviour of D2 Tool Steel – An Experimental Investigationˮ, Materials Today: Proceedings, 4(8), 7665–7673 (2017).
• [37] B. Podgornik, I. Paulin, B. Zajec, S. Jacobson, and V. Leskovšek, “Deep cryogenic treatment of tool steelsˮ, Journal of Materials Processing Technology, 229, 398‒406 (2016).
• [38] A.V. Pradeep, S.V. Prasad, L.V. Suryam, Y.K. Rao, and D. Kesava, “Effect of Cryogenic Treatment on Tool Life of HSS Tool (S400) and Surface Finish of the Material in Turning of SS304ˮ, Mater.Sci.Eng. 149, 1–11 (2016).
• [39] H.B. He et al., “Effect of deep cryogenic treatment on machinability and wear mechanism of TiAlN coated tools during dry turningˮ, Int.J.Precis.Eng.Manuf. 15(4), 655–660 (2014)

Uwagi

PL

Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2020).