Effect of single roll drive cross rolling on the microstructure, crystallographic texture, and mechanical behavior of Al–Zn–Mg–Cu alloy

• Autorzy: Kazemi-Navaee Amir , Jamaati Roohollah , Aval Hamed Jamshidi

Identyfikatory

DOI

10.1007/s43452-021-00362-9

• Języki publikacji: EN

Abstrakty

EN

In this work, the effect of single roll drive cross rolling on the microstructure, crystallographic texture, hardness, tensile properties, and fracture behavior of AA7075 aluminum alloy was investigated. It was found that with increasing the thickness reduction, the grain size reduced and the average width of grain for the 40% deformed sample decreased to 3.7 ± 0.4 µm. Due to the nature of the cross-rolling process, several X-type shear bands were observed after 40% deformation. The recrystallization texture is notably intensified to its highest value of 4.4 × R, after only 20% cold deformation due to the occurrence of continuous dynamic recrystallization (CDRX). The intensity of recrystallization texture sharply dropped to its lowest value of 2.7 × R. This was due to the rotation of Goss-orientated new grains in the 20% deformed sample toward copper orientation during 40% rolling. With increasing the thickness reduction, the overall texture intensity significantly reduced owing to the nature of the cross-rolling process in which the rolling direction rotates 90° after each 10% strain. Two texture transitions were observed along τ fiber: rolling (copper) texture to recrystallization (Goss) texture after 20% thickness reduction and recrystallization to the rolling texture after 40% deformation. The hardness and strength increased by increasing the thickness reduction, while the ductility decreased. After a 40% thickness reduction, yield strength significantly increased from 138.3 ± 4.4 MPa (for initial sample) to the highest value of 580.5 ± 11.5 MPa, demonstrating 320% increment, in the 0° direction. This increment for 45° and 90° direction was 265% and 337%, respectively. By 40% rolling, the value of in-plane anisotropy (IPA) remarkably decreased to its lowest value of 3.4% due to texture weakening. With increasing the rolling reduction to 20%, the severity of Portevin–Le Chatelier (PLC) increased in the flow curves due to the occurrence of CDRX and also strengthening of the rotated cube {001} < 110 > and E {111} < 110 > components. With increasing the rolling reduction, the size of cleavage facets and the severity of delamination increased, and the number and depth of dimples decreased.

Słowa kluczowe

EN

aluminum alloys; asymmetric rolling; microstructure; texture; hardness; tensile behavior

PL

stopy aluminium; walcowanie asymetryczne; mikrostruktura; twardość; rozciąganie

• Wydawca: Springer ; Wrocław University of Science and Technology
• Czasopismo: Archives of Civil and Mechanical Engineering
• Rocznik: 2022
• Tom: Vol. 22, no. 1
• Strony: art. no. e41, 2022
• Opis fizyczny: Bibliogr. 20 poz., rys., wykr.

Twórcy

autor

Kazemi-Navaee Amir

• Department of Materials Engineering, Babol Noshirvani University of Technology, Shariati Ave., 47148– 71167 Babol, Iran

autor

Jamaati Roohollah

• Department of Materials Engineering, Babol Noshirvani University of Technology, Shariati Ave., 47148– 71167 Babol, Iran

• https://orcid.org/0000-0002-4764-9910

autor

Aval Hamed Jamshidi

• Department of Materials Engineering, Babol Noshirvani University of Technology, Shariati Ave., 47148– 71167 Babol, Iran

Bibliografia

• 1. Deng YL, Wan L, Zhang Y, Zhang XM. Evolution of microstructures and textures of 7050 Al alloy hot-rolled plate during staged solution heat-treatments. J Alloy Compd. 2010;498:88–94.
• 2. Hidalgo-Manrique P, Cepeda-Jiménez CM, Ruano OA, Carreño F. Effect of warm accumulative roll bonding on the evolution of microstructure, texture and creep properties in the 7075 aluminium alloy. Mater Sci Eng, A. 2012;556:287–94.
• 3. Jayaganthan R, Brokmeier HG, Schwebke B, Panigrahi SK. Microstructure and texture evolution in cryorolled Al 7075 alloy. J Alloy Compd. 2010;496:183–8.
• 4. Magalhães DCC, Hupalo MF, Cintho OM. Natural aging behavior of AA7050 Al alloy after cryogenic rolling. Mater Sci Eng A. 2014;593:1–7.
• 5. Mondal C, Singh AK, Mukhopadhyay AK, Chattopadhyay K. Effects of different modes of hot cross-rolling in 7010 aluminum alloy: part I. Evolution of microstructure and texture. Metall Mater Trans A. 2013;44:2746–63.
• 6. Nayan N, Mishra S, Prakash A, Murty SVSN, Prasad MJNV, Samajdar I. Effect of cross-rolling on microstructure and texture evolution and tensile behavior of aluminium-copper-lithium (AA2195) alloy. Mater Sci Eng A. 2019;740:252–61.
• 7. Mondal C, Singh AK, Mukhopadhyay AK, Chattopadhyay K. Effects of different modes of hot cross-rolling in 7010 aluminum alloy: part II. Mechanical properties anisotropy. Metall Mater Trans A. 2013;44:2764–77.
• 8. Suwas S, Ray RK. Crystallographic texture of materials. 1st ed. Manchester: Springer, Brian Derby; 2014.
• 9. Humphreys J, Rohrer GS, Rollett A. Recrystallization and related annealing phenomena. 3rd ed. Oxford: Elsevier Science Ltd.; 2017.
• 10. Jin H, Lloyd DJ. The reduction of planar anisotropy by texture modification through asymmetric rolling and annealing in AA5754. Mater Sci Eng A. 2005;399:358–67.
• 11. Magalhães DCC, Kliauga AM, Ferrante M, Sordi VL. Asymmetric cryorolling of AA6061 Al alloy: strain distribution, texture and age hardening behavior. Mater Sci Eng A. 2018;736:53–60.
• 12. Goli F, Jamaati R. Effect of strain path during cold rolling on the microstructure, texture, and mechanical properties of AA2024 aluminum alloy. Mater Res Express. 2019;6:066514.
• 13. Goli F, Jamaati R. Asymmetric cross rolling (ACR): a novel technique for enhancement of Goss/Brass texture ratio in Al-Cu-Mg alloy. Mater Charact. 2018;142:352–64.
• 14. Goli F, Jamaati R. Intensifying Goss/Brass texture ratio in AA2024 by asymmetric cold rolling. Mater Lett. 2018;219:229–32.
• 15. Kazemi-Navaee A, Jamaati R, Aval HJ. Asymmetric cold rolling of AA7075 alloy: the evolution of microstructure, crystal-lographic texture, and mechanical properties. Mater Sci Eng A. 2021;824:141801.
• 16. Li H, Chen P, Wang Z, Zhu F, Song R, Zheng Z. Tensile properties, microstructures and fracture behaviors of an Al-Zn-Mg-Cu alloy during ageing after solution treating and cold-rolling. Mater Sci Eng A. 2019;742:798–812.
• 17. Amininejad A, Jamaati R, Hosseinipour SJ. Improvement of strength-ductility balance of SAE 304 stainless steel by asymmetric cross rolling. Mater Chem Phys. 2020;256:123668.
• 18. Jamaati R. Unexpected Cube texture in cold rolling of copper. Mater Lett. 2017;202:111–5.
• 19. Zhang P, Song A, Fang Y, Yue X, Wang Y, Yu X. A study on the dynamic mechanical behavior and microtexture of 6082 aluminum alloy under different direction. Vacuum. 2020;173:109119.
• 20. Nayan N, Narayana Murty SVS, Jha AK, Pant B, Sharma SC, George KM, Sastry GVS. Mechanical properties of aluminium–copper–lithium alloy AA2195 at cryogenic temperatures. Mater Design. 2014;58:445–50.

Uwagi

PL

Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023)