Introduction of Powder Fluxes in Rotary Degassing System Towards Intensifying Refining Process of Aluminium Alloys

• Autorzy: Piękoś M. , Smorawiński Z.

Identyfikatory

DOI

10.24425/afe.2024.151315

• Języki publikacji: EN

Abstrakty

EN

This paper presents and describes the research capabilities of a prototype experimental bench for realising the composite processing of liquid aluminium alloys by involving gas refining by rotary degassing technology and refining with salts (fluxes) in powder form. The constructed unit was installed in the Experimental Foundry of the Faculty of Foundry Engineering at AGH in the Department of Moulding Processes, Mould Technology, and Non-Ferrous Metals Foundry; it is an integral part of a thyristor-based medium-frequency induction furnace with a melting capacity of up to 60 kg for aluminium alloys. The new experimental bench performs barbotage refining using a rotating head with the possibility of alternating the introduction of refiners/modifiers in powder form. This method can be used in casting lines: continuous in reactors, or batch in ladles. The innovation of the design of the stand and the treatment of the liquid metal with powdered additives consists of dosing the refiner fluid deep into the metal bath through a channel that was made in the rotor axis and the head; this differs from conventional methods in the small amounts of introduced salts and, at the same time, in the very good metal-inert gas-salt homogeneity of the treated metal bath. This method of dosing the refining salts increases the efficiency of their use, reduces any losses, and limits the formation of post-refining slag (thus, minimising the negative environmental effect). The feedstock that was used for the test smelts consisted of recycled materials: aluminium 99.7 (in the form of wires of various cross-sections that were used in electrical engineering – so-called ‘SECTOR’), and the sub-eutectic AlSi7Mg0.3 alloy (in ingot form). The scope of the tests included verifying the technical solutions that were adopted for the dosing of the bulk materials in the form of a fluid, selecting the melting temperature, and dispersing (distributing) the materials in the bath via the rotor head. The results of the trials were reviewed in terms of the changes in the hydrogen content of the performed process and information on such powder-flux-introduction parameters as the type of the rotor head and the melting temperature of the powder flux. Preliminary trials showed that the performed complex refining (rotary degassing + refining with salts being blown as a fluid into the lower parts of the liquid metal) allowed us to reduce the hydrogen content to a level that could not be achieved by gas refining alone.

Słowa kluczowe

EN

casting; aluminium alloys; degassing process; rotary degassing; powder fluxes into metal

PL

odlewanie; stopy aluminium; odgazowywanie; topniki proszkowe do metalu

• Wydawca: Komisja Odlewnictwa Polskiej Akademii Nauk Oddział w Katowicach
• Czasopismo: Archives of Foundry Engineering
• Rocznik: 2024
• Tom: Vol. 24, iss. 4
• Strony: 89--94
• Opis fizyczny: Bibliogr. 32 poz., il., tab., wykr.

Twórcy

autor

Piękoś M.

• AGH University of Science and Technology, Faculty of Foundry Engineering, Krakow, Poland

• https://orcid.org/0000-0002-2725-6642

autor

Smorawiński Z.

• Technologia & Technika Aluminium, Konin, Poland

Bibliografia

• [1] Oczkoś, K., Kawalec, A. (2012). The forming of light metals, Warszawa: Wydawnictwo Naukowe PWN. (in Polish).
• [2] Pietrowski, S., Szymczak, Siemińska-Jankowska, T. B. & Jankowski, A. (2010). Selected characteristic of silumins with additives of Ni, Cu, Cr, Mo, W and V. Archives of Foundry Engineering. 10(2), 107-126. ISSN (1897-3310).
• [3] Rzadkosz, S. & Staszczak, L. (2007). Effect of selected microadditives on mechanical properties of aluminum alloys. Archives of Foundry Engineering. 7(1), 85-88. ISSN (1897-3310).
• [4] Soiński, M.S. & Jakubus, A. (2021) The leading role of aluminium in the growing production of castings made of the non-ferrous alloys. Archives of Foundry Engineering. 21(3), 33-44. DOI: 10.24425/afe.2021.136110.
• [5] Soiński, M.S., Jakubus, A., Kordas, P. & Skurka, K. (2015). Production of castings in the world and in selected countries from 1999 to 2013. Archives of Foundry Engineering. 15(spec.1), 103-110.
• [6] Polmear, I., StJohn, D., Nie J.-F. & Qian, M. (2017). Light Alloys: Metallurgy of the Light Metals. Butterworth-Heinemann.
• [7] Goehler, D.D. (1988). Process of innovations and advancements in aluminum casting technology. In AFS Special Conference, 1998 (pp.103-06). City of Industry, CA, American Foundarymen’s Society, Des Plaines, IL.
• [8] Wang, Q.G. (2003). Microstructural effects on the tensile and fracture behavior of aluminum casting alloys A356/357. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. 34, 2887-2899. DOI: 10.1007/s11661-003-0189-7.
• [9] Farahany, S., Ourdjini, A., Idris, M.H. & Shabestari, S.G., (2013). Computer-aided cooling curve thermal analysis of near eutectic Al-Si-Cu-Fe alloy: Effect of silicon modifier/refiner and solidification conditions on the nucleation and growth of dendrites. Journal of Thermal Analysis and Calorimetry. 114, 705-717. DOI: 10.1007/s10973-013-3005-7.
• [10] Czekaj, E., Zych, J., Kwak, Z. & Garbacz-Klempka, A. (2016). Quality index of the AlSi7Mg0.3 aluminium casting alloy depending on the heat treatment parameters. Archives of Foundry Engineering. 16(3), 25-28. DOI: 10.1515/afe-2016-0043.
• [11] Orłowicz, A.W. & Mróz, M. (2004). Improvement the quality index of Al-Si castings alloy. Archives of Foundry. 4(14), 363- 368. (in Polish).
• [12] Czekaj, E., Nykiel, J., Kwak, Z., Garbacz-Klempka, A. & Nykiel, M. (2018). The influence of selected refining methods of AlSi7Mg0.3 silumin on its quality index. Archives of Foundry Engineering. 18(2), 72-78. DOI: 10.24425/122505.
• [13] Stulgis, G. (2013). Recycling of aluminum - the link of economy. Recykling odpadów (Waste recycling). 6(150), 22- 24. (in Polish).
• [14] Rzadkosz, S., Zych, J., Piękoś, M., Kozana, J., Garbacz-Klempka, A., Kolczyk, J. & Jamrozowicz, Ł. (2015) Influence of refining treatments on the properties of Al-Si alloys. Metalurgija. 54(1), 35-38. ISSN 0543-5846. http://hrcak.srce.hr/file/187164.
• [15] Kozana, J., Piękoś, M. & Garbacz-Klempka, A. (2018). Issues concerning the structure and properties of AlSi7Mg alloys and die castings for the automotive industry. In F. Romankiewicz, R. Romankiewicz, R. Ulewicz (Eds.), Advanced manufacturing and repair technologies in vehicle industry (pp. 163-191). Zielona Góra. (in Polish).
• [16] Bonderek, Z., Piękoś, M., Smorawiński, Z. (2022). Casting of aluminum alloys: science and technology. Wydawnictwo Naukowe Akapit.
• [17] Gursoy, O., Erzi, E., Tur, K., D. & Dispinar, D. (2020) Evolution of aluminium melt quality of A356 after several recycling. Archives of Foundry Engineering. 20(4), 61-66. DOI: 10.24425/afe.2020.133348.
• [18] Orłowicz, W., Mróz, M. & Tupaj, M. (2006) Effect of modification with sodium or strontium on microstructure and mechanical properties of AlSi7Mg alloy. Archives of Foundry. 6(18), 117-124. ISSN 1642-5308.
• [19] Saternus, M. (2011). Refining of aluminium and its alloys by argon purging. Gliwice: Wydawnictwo Politechniki Śląskiej. (in Polish).
• [20] Tupaj, M., Orłowicz, A.W., Trytek, A. & Mróz, M. (2019). Improvement of Al-Si alloy fatigue strength by means of refining and modification. Archives of Foundry Engineering. 19(4), 61-66. DOI: 10.24425/afe.2019.129631.
• [21] Galarraga, H., de Cortazar, M.G., Arregi, E., Artola, A., Oncala, J.L. & Merchan, M., (2020) Gas blowing ultrasonic aluminium degassing assessment with the reduced pressure test (RPT) method. Archives of Foundry Engineering. 20(2), 111-117. DOI: 10.24425/afe.2020.131312.
• [22] Sigworth, G.K. (2021). Refining of secondary aluminum: important chemical factors. JOM. 73(9), 2594-2602. DOI: 10.1007/s11837-021-04774-z.
• [23] Saternus, M. (2012). Influence of impeller shape on the gas bubbles dispersion in aluminium refining process. Journal of Achievements in Materials and Manufacturing Engineering. 55(2), 285-290.
• [24] Orłowicz, A.W., Mróz, M., Tupaj, M., Betlej, J. & Płoszaj, F. (2009). Use of barbotage refining of aluminum-silicon alloy to improve mechanical properties of high pressure die castings. Archives of Foundry Engineering. 9(2), 41-44. ISSN (1897-3310).
• [25] Karban. P., Leszczyńska-Madej. B. (2023). Effect of barbotage refining time and recycled scrap content on the microstructure of EN AC 44200 alloy. Materials Today Communications. 37, 107038, 1-6. https://doi.org/10.1016/j.mtcomm.2023.107038.
• [26] Poniewierski, Z. (1989). Crystallization, structure and properties of silumins. Warszawa: WNT. (in Polish).
• [27] Jung, W.-G., Lee J.-W. & Kim, W.-Y. (2013). Magnesium removal from molten aluminum by Cl2 bubbling. Metals and Materials International. 19(6), 1275-1281. DOI: 10.1007/s12540-013-6020-0.
• [28] Zych, J.S., Janus, A. & Smorawiński, Z. (2022). Improvements of industrial AlSi alloys in a complex treatment of the degassing process. Przegląd Odlewnictwa. 5-6, 248-255.
• [29] Gyarmati, G., Fegyverneki, G., Tokár, M. et al. (2021). The Effects of rotary degassing treatments on the melt quality of an Al-Si casting alloy. International Journal of Metalcasting. 15, 141-151. https://doi.org/10.1007/s40962-020-00428-z.
• [30] Smorawiński, Z. (2020). MDS_3F – new quality of equipment for the barbotage degassing of aluminium and its alloy. Przegląd Odlewnictwa. 7-8, 254-256. (in Polish).
• [31] Breton, F., Larouche, A., Waite, P., Côté, P. (2015). Rotary flux injector (RFI): Recent development towards an autonomous technology. Light Metals. 901-904. https://doi.org/10.1007/978-3-319-48248-4_151.
• [32] Neff, D., Sigworth, G. & Gallo, R. (2018). Melting and melt treatment of aluminum alloys. In: J. G. K. Kevin Anderson, John Weritz (Eds.), ASM Handbook, Volume 2A, Aluminum Science and Technology (pp. 143-164). ASM International. https://doi.org/10.31399/asm.hb.v02a.a0006535.

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa nr POPUL/SP/0154/2024/02 w ramach programu "Społeczna odpowiedzialność nauki II" - moduł: Popularyzacja nauki (2025)