Application of Taguchi methods (doe) in composite engineering

• Autorzy: Lesiuk Grzegorz , Zielonka Paweł , Olaleye Kayode , Soogabbe Japhet , Lafarga Adrian Ferrer

Identyfikatory

DOI

10.37190/JoT2023_05

• Języki publikacji: EN

Abstrakty

EN

In the paper, a design of experiment (DOE) in terms of the Taguchi method was used for the optimization of the manufacturing process. This approach makes it possible to do fewer experiments while still getting the desired outcomes. This research programme will use this tool to optimize the resin casting process by monitoring manufacturing parameters like temperature, curing time, and flameretardant concentration. Thus, this study aims to determine the ideal set of parameters for the resin casting of composite materials. Based on experimental results, it was possible to find crucial factors and their influence on the fracture strength of resin for composite manufacturing systems.

Słowa kluczowe

EN

composite; Taguchi method; flame retardant; epoxy resin

PL

kompozyty; metoda Taguchiego; środek zmniejszający palność; żywica epoksydowa

• Wydawca: Oficyna Wydawnicza Politechniki Wrocławskiej
• Czasopismo: Journal of TransLogistics
• Rocznik: 2023
• Tom: Vol. 19
• Strony: 51--61
• Opis fizyczny: Bibliogr. 25 poz., rys., tab

Twórcy

autor

Lesiuk Grzegorz

• Faculty of Mechanical Engineering, Wrocław University of Science and Technology

autor

Zielonka Paweł

autor

Olaleye Kayode

autor

Soogabbe Japhet

autor

Lafarga Adrian Ferrer

Bibliografia

• [1] Mouritz AP. Introduction to aerospace materials. Elsevier; 2012.
• [2] Sojka SA, Moniz WB. The curing of an epoxy resin as followed by carbon‐13 NMR spectroscopy. J Appl Polym Sci 1976;20:1977-82.
• [3] Cañavate J, Colom X, Pages P, Carrasco F. Study of the curing process of an epoxy resin by FTIR spectroscopy. Polym. Plast Technol. Eng. 2000;39:937-43.
• [4] González MG, Cabanelas JC, Baselga J. Applications of FTIR on epoxy resins-identification,monitoring the curing process, phase separation and water uptake. Infrared Spectroscopy-Materials Science, Engineering and Technology 2012;2:261-84.
• [5] Massingill Jr JL, Pabon Jr RA. Modified advanced epoxy resins 1989.
• [6] May C. Epoxy resins: chemistry and technology. Routledge; 2018.
• [7] Wu F, Zhou X, Yu X. Reaction mechanism, cure behavior and properties of a multifunctional epoxy resin, TGDDM, with latent curing agent dicyandiamide. RSC Adv 2018;8:8248–58.
• [8] Erdmann M, Trappe V, Sturm H, Braun U, Duemichen E. Cure conversion of structural epoxies by cure state analysis and in situ cure kinetics using nondestructive NIR spectroscopy. Thermochim Acta 2017;650:8-17.
• [9] Mphahlele K, Ray SS, Kolesnikov A. Cure kinetics, morphology development, and rheology of a high-performance carbon-fiber-reinforced epoxy composite. Compos B Eng 2019;176:107300.
• [10] Rogers MG. The structure of epoxy resins using NMR and GPC techniques. J Appl Polym Sci 1972;16:1953-8.
• [11] Merad L, Cochez M, Margueron S, Jauchem F, Ferriol M, Benyoucef B, et al. In-situ monitoring of the curing of epoxy resins by Raman spectroscopy. Polym Test 2009;28:4205.
• [12] Wang LW, Fernando GF. Cure monitoring of epoxy resin by simultaneous DSC/FTIR. Adv. Mat Res 2014;881:90508.
• [13] Uttarwar PB, Raini SK, Malwad DS. Optimization of process parameter on Surface Roughness (Ra) and Wall Thickness on SPIF using Taguchi method. International Research Journal of Engineering and Technology 2015;2:781-4.
• [14] Naiju CD, Anil PM. Influence of operating parameters on the reciprocating sliding wear of direct metal deposition (DMD) components using Taguchi method. Procedia Eng 2017;174:1016-27.
• [15] Lee BH, Abdullah J, Khan ZA. Optimization of rapid prototyping parameters for production of flexible ABS object. J Mater Process Technol 2005;169:54-61.
• [16] Uddin MS, Sidek MFR, Faizal MA, Ghomashchi R, Pramanik A. Evaluating mechanical properties and failure mechanisms of fused deposition modeling acrylonitrile butadiene styrene parts. J Manuf. Sci. Eng 2017;139:081018.
• [17] Hamza I, Abdellah EG, Mohamed O. Experimental optimization of fused deposition modeling process parameters: a Taguchi process approach for dimension and tolerance control. Proceedings of the international conference on industrial engineering and operations management, 2018, p. 2992-3.
• [18] Ahmad MN, Ab Rahman MH, Maidin NA, Osman MH, Wahid MK, Mohamed Saiful Firdaus H, et al. Optimization on Surface Roughness of Fused Deposition Modelling (FDM) 3D printed parts using taguchi approach. Intelligent Manufacturing and Mechatronics: Proceedings of the 2nd Symposium on Intelligent Manufacturing and Mechatronics-SympoSIMM 2019, 8 July 2019, Melaka, Malaysia, Springer; 2020, p. 230–43.
• [19] Ahmad MN, Ab Rahman MH, Maidin NA, Osman MH, Wahid MK, Mohamed Saiful Firdaus H, et al. Optimization on Surface Roughness of Fused Deposition Modelling (FDM) 3D printed parts using taguchi approach. Intelligent Manufacturing and Mechatronics: Proceedings of the 2nd Symposium on Intelligent Manufacturing and Mechatronics-SympoSIMM 2019, 8 July 2019, Melaka, Malaysia, Springer; 2020, p. 230-43.
• [20] Qattawi A. Investigating the effect of fused deposition modeling processing parameters using Taguchi design of experiment method. J Manuf Process 2018;36:164-74.
• [21] Onwubolu GC, Rayegani F. Characterization and optimization of mechanical properties of ABS parts manufactured by the fused deposition modelling process. International Journal of Manufacturing Engineering 2014;2014:1-13.
• [22] Uddin MS, Sidek MFR, Faizal MA, Ghomashchi R, Pramanik A. Evaluating mechanical properties and failure mechanisms of fused deposition modeling acrylonitrile butadiene styrene parts. J Manuf. Sci. Eng. 2017;139:081018.
• [23] Fett, T.; Gerteisen, G.; Hahnenberger, S.; Martin, G.; Munz, D. Fracture tests for ceramics under mode-I, mode-II and mixed-mode loading. J. Eur. Ceram. Soc. 1995, 15, 307–312.
• [24] Fett, T. Stress intensity factors for edge crack subjected to mixed mode four-point bending. Theor. Appl. Fract. Mech. 1991, 15, 99-104.
• [25] Araki, W.; Nemoto, K.; Adachi, T.; Yamaji, A. Fracture toughness for mixed mode I/II of epoxy resin. Acta Mater. 2005, 53, 869-875.

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2024).