Effect of Heat Input During Disk Laser Bead-On-Plate Welding of Thermomechanically Rolled Steel on Penetration Characteristics and Porosity Formation in the Weld Metal

• Autorzy: Lisiecki A.

Identyfikatory

DOI

0.1515/amm-2016-0019

• Języki publikacji: EN

Abstrakty

EN

The paper presents a detailed analysis of the influence of heat input during laser bead-on-plate welding of 5.0 mm thick plates of S700MC steel by modern Disk laser on the mechanism of steel penetration, shape and depth of penetration, and also on tendency to weld porosity formation. Based on the investigations performed in a wide range of laser welding parameters the relationship between laser power and welding speed, thus heat input, required for full penetration was determined. Additionally the relationship between the laser welding parameters and weld quality was determined.

Słowa kluczowe

EN

disk laser; welding; thermomechanically rolled steel

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2016
• Tom: Vol. 61, iss. 1
• Strony: 93--102
• Opis fizyczny: Bibliogr. 42 poz., fot., rys., tab., wykr.

Twórcy

autor

Lisiecki A.

• The Silesian University of Technology, Faculty of Mechanical Engineering, Welding Department, 18A Konarskiego str., 44-100 Gliwice, Poland

Bibliografia

• [1] Rajashekhar S. Sharma, PalMolian, Weldability of advanced high strength steels using an Yb:YAG disk laser, Journal of Materials Processing Technology 211, 1888-1897 (2011).
• [2] A. Grajcar, M. Różański, S. Stano, A. Kowalski, B. Grzegorczyk, Effect of Heat Input on Microstructure and Hardness Distribution of Laser Welded Si-Al TRIP-Type Steel, Adv. in Mat. Sci. and Eng. 2014 (2014).
• [3] A. Lisiecki, Diode laser welding of high yield steel. Proceedings of SPIE, Laser Technology, Applications of Lasers 8703, 22 (2012).
• [4] J. Górka, Analysis of simulated welding thermal cycles S700MC using a thermal imaging camera, Adv. Mat. Res. ISI Proceedings 837, 375-380 (2014).
• [5] J. Górka, Influence of the maximum temperature of the thermal cycle on the properties and structure of the HAZ of steel S700MC, IOSR J. of Eng. 3(11), 22-28 (2013).
• [6] M. Opiela, A. Grajcar, Hot deformation behavior and softening kinetics of Ti-V-B microalloyed steels, Arch. Civ. Mech. Eng. 12(3), 327-333 (2012).
• [7] L. A. Dobrzański, A. Grajcar, W. Borek, Microstructure evolution of C-Mn-Si-Al-Nb high-manganese steel during the thermomechanical processing, Mat. Sci. Forum 638, 3224-3229 (2010).
• [8] W. Sitek, J. Trzaska, L. A. Dobrzański, Modified Tartagli method for calculation of Jominy hardenability curve, Mat. Sci. Forum 575-578, 892-897 (2008).
• [9] T. Węgrzyn, R. Wieszała, Main steel covered electrodes in terms of the Mount of oxygen in weld metal deposits (WMD), Metalurgija 51, 183-186 (2012).
• [10] T. Węgrzyn, J. Piwnik, R. Wieszala, D. Hadryś, Control over the steel welding structure parameters by micro-jet cooling, Archives Of Metallurgy And Materials 57(3), 679-684 (2012).
• [11] J. Slania, B. Slazak, M. Fidali, Application of fast fourier transform (FFT) in the analysis of a welding current instantaneous values waveforms during welding with a covered electrode, Arch. Metall. Mater. 59(2), 569-573 (2014).
• [12] W. Sitek, A mathematical model of the hardness of high-speed steels, Transactions of Famena, 34 (3) 39-46 (2010).
• [13] T. Węgrzyn, J. Mirosławski, A. Silva, D. Pinto, M. Miros, Oxide inclusions in steel welds of car body, Materials Science Forum 6, 585-591 (2010).
• [14] T. Węgrzyn, Mathematical Equations of the Influence of Molybdenum and Nitrogen in Welds. Conference of International Society of Offshore and Polar Engineers ISOPE´2002, Kita Kyushu, Japan 2002, Copyright by International Society of Offshore and Polar Engineers, vol. IV, ISBN 1-880653-58-3, Cupertino - California - USA 2002.
• [15] A. Kurc-Lisiecka, W. Ozgowicz, W. Ratuszek, J. Kowalska, Analysis of Deformation Texture in AISI 304 Steel Sheets, Sol. St. Phenomena 203-204, 105-110 (2013).
• [16] K. Janerka, D. Bartocha, J. Szajnar, J. Jezierski, The carburizer influence on the crystallization process and the microstructure of synthetic cast iron, Arch. Metall. Mater. 55(3), 851-859 (2010).
• [17] J. Kusiński, S. Kac, A. Kopia, A. Radziszewska, M. Rozmus- Górnikowska, B. Major, L. Major, J. Marczak, A. Lisiecki, Laser modification of the materials surface layer - a review paper. Bulletin of the Polish Academy of Sciences, Technical Sciences, 60(4), 711-728 (2012).
• [18] K. Janerka, M. Pawlyta, J. Jezierski, J. Szajnar, D. Bartocha, Carburiser properties transfer into the structure of melted cast iron, J. Mat. Proc. Tech. 214(4), 2014 794-801.
• [19] L. A. Dobrzański, M. Krupiński, K. Labisz, B. Krupińska, A. Grajcar: Phases and structure characteristics of the near eutectic Al-Si-Cu alloy using derivative thermo analysis, Materials Science Forum 638-642, 475-480 (2010).
• [20] R. Burdzik, P. Folęga, B. Łazarz, Z. Stanik, J. Warczek, Analysis of the impact of surface layer parameters on wear intensity of frictional couples, Archives of Metallurgy and Materials 57 (4), 987-993 (2012).
• [21] L. Blachaa, Bleientfernung aus kupferlegierungen im prozess der vakuumraffination, Archives of Materials and Metallurgy 48 (1), 105-127 (2003).
• [22] A. Fornalczyk, M. Saternus, Platinum recovery from used auto catalytic converters in electrorefining process. Metalurgija 52(2) 219-222 (2012).
• [23] L. Blacha, R. Burdzik, A. Smalcerz, T. Matuła, Effects of pressure on the kinetics of manganese evaporation from the OT4 alloy, Archives Of Metallurgy And Materials 58 (1), 197-201 (2013).
• [24] A. Kaźmierczak-Bałata, J. Bodzenta, D. Trefon-Radziejewska, Determination of thermal-diffusivity dependence on temperature of transparent samples by thermal wave method, International Journal of Thermophysics 31 (1), 180-186 (2010).
• [25] J. Bodzenta, A. Kaźmierczak, T. Kruczek, Analysis of thermograms based on FFT algorithm, Journal de Physique IV 129, 201-206 (2005).
• [26] A. Lisiecki: Welding of titanium alloy by Disk laser. Proceedings of SPIE, Laser Technology, Applications of Lasers, 87030 (2013).
• [27] T. Węgrzyn The Classification of metal weld deposits in terms of the amount of nitrogen, Proceedings . Conference of International Society of Offshore and Polar Engineers ISOPE´2001, Stavanger, Norway 2001, International Society of Offshore and Polar Engineers, vol. IV, Cupertino - California, USA, 2001 282-285.
• [28] T. Węgrzyn, J. Piwnik, R. Wieszała, D. Hadryś, Control over the steel welding structure parameters by micro-jet cooling, Archives of Metallurgy and Materials 57(1), 679-685 (2012).
• [29] R. Burdzik, Ł. Konieczny, T. Figlus, Concept of on-board comfort vibration monitoring system for vehicles, J. Mikulski (Ed.): Activities of Transport Telematics, TST, CCIS 395, 418-425 (2013).
• [30] R. Burdzik, Research on the influence of engine rotational speed to the vibration penetration into the driver via feet - multidimensional analysis, Journal of Vibroengineering 15(4), 2114-2123 (2013).
• [31] Ł. Konieczny, R. Burdzik, B. Łazarz, Application of the vibration test in the evaluation of the technical condition of shock absorbers built into the vehicle, submitted to Journal of Vibroengineering 15(4), 2042-2048 (2013).
• [32] R. Burdzik, Implementation of multidimensional identification of signal characteristics in the analysis of vibration properties of an automotive vehicle’s floor panel, Eksploatacja i Niezawodnosc - Maintenance and Reliability 16(3), 439-445 (2014).
• [33] D. Janicki, Fiber laser welding of nickel based superalloy Rene 77, Proc. SPIE, Laser Technology 2012: Applications of Lasers, 2013, 8703, 87030Q, doi: 10.1117/12.2013428.
• [34] D. Janicki, Fiber laser welding of nickel based superalloy Inconel 625, Proc. SPIE, Laser Technology 2012: Applications of Lasers, 2013, 8703, 87030R, doi: 10.1117/12.2013430.
• [35] L. A. Dobrzański, M. Bonek, M. Piec, E. Jonda, Diode laser modification of surface gradient layer properties of a hot-work tool steel, Mat. Sci. Forum (532-533) 657-660 (2006).
• [36] M. Musztyfaga, L. A. Dobrzański, S. Rusz, M. Staszuk, Application examples for the different measurement modes of electrical properties of the solar cells, Arch. Metall. Mater. 59(1), 247-252 (2014).
• [37] R. Burdzik, Ł. Konieczny, Z. Stanik, P. Folega, A. Smalcerz, A. Lisiecki, Analysis of impact of chosen parameters on the wear of camshaft, Arch. Metall. Mater. 59(3), 961-967 (2014).
• [38] M. Urzynicok, K. Kwiecinski, J. Slania, Analysis of problems occured during welding of new genreation bainitic steel 7CrMoVTiB10-10 (T24), Arch. Metall. Mater. 58(3), 691-696 (2013).
• [39] A. Klimpel, A. Lisiecki, A. Szymanski, A.P. Hoult, Numerical and experimental determination of weld pool shape during high-power diode laser welding, Proc. of SPIE Vol. 5229, Laser Technology VII: Applications of Lasers, 6 Oct. 2003, pp. 247-250, doi:10.1117/12.520726.
• [40] J. T. Norris, C. V. Robino, D. A. Hirschfeld, M. J. Perricone, Effects of Laser Parameters on Porosity Formation: Investigating Millimeter Scale Continuous Wave Nd:YAG Laser Welds, Welding Journal 90, 198-203 (2011).
• [41] M. J. Torkamany, J. Sabbaghzadeh, M. J. Hamedi, Effect of laser welding mode on the microstructure and mechanical performance of dissimilar laser spot welds between low carbon and austenitic stainless steels, Materials and Design 34, 666-672 (2012).
• [42] J. Słania, Influence of phase transformations in the temperature ranges of 1250-1000ºC and 650-350ºC on the ferrite content in austenitic welds made with T 23 12 LRM3 tubular electrode. Archives of Metallurgy and Materials 50(3), 757-767(2005).

Uwagi

PL

Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę