Improvement of ductility for Twin Roll Cast and rolled AZ31 strips by use of Taguchi method

• Autorzy: Ullmann M. , Saleh H. , Schmitdchen M. , Kawalla R. , Vogt H. P.
• Języki publikacji: EN

Abstrakty

EN

Magnesium alloys have great potential in the area of lightweight production especially in the automotive industry due to their favorable combination of mechanical properties and low density. The effects of various rolling parameters on ductility were investigated using the Taguchi method. The optimum combination of process parameters has been found through analysis of main effects of ductility and signal-to-noise ratio, and the significant parameter were identified depending on analysis of variance. The results demonstrate that reduction is the most important factor for improving the ductility of the final strips, followed by rolling temperature and rolling speed. The optimal levels for the controllable factors were rolling temperature of 375 °C, rolling speed of 175 m/min and reduction of 70% for higher ductility.

Słowa kluczowe

EN

Taguchi method; experimental design; magnesium alloy; rolling

PL

metoda Taguchi; projekt eksperymentalny; stopy magnezu; walcówka

• Wydawca: Springer ; Wrocław University of Science and Technology
• Czasopismo: Archives of Civil and Mechanical Engineering
• Rocznik: 2013
• Tom: Vol. 13, no. 1
• Strony: 1--6
• Opis fizyczny: Bibliogr. 11 poz., rys., tab., wykr.

Twórcy

autor

Ullmann M.

• Institute of Metal Forming, TU Bergakademie, Freiberg, Germany

autor

Saleh H.

• Institute of Metal Forming, TU Bergakademie, Freiberg, Germany

autor

Schmitdchen M.

• Institute of Metal Forming, TU Bergakademie, Freiberg, Germany

autor

Kawalla R.

• Institute of Metal Forming, TU Bergakademie, Freiberg, Germany

autor

Vogt H. P.

Bibliografia

• [1] R. Kawalla, G. Lehmann, M. Ullmann, Magnesium semifinished products for vehicle construction, Archives of Civil and Mechanical Engineering, Wrocław VIII (2) (2008) 93–101.
• [2] R. Kawalla, M. Oswald, C. Schmidt, M. Ullmann, H.P. Vogt, N.D. Cuong, New technology for the production of magnesium strips and sheets, Metalurgija 47/3 (2008) 195–198.
• [3] R. Kawalla, M. Ullmann, Magnesium sheet production state and perspectives. Poznan-Wasowo: new materials for advanced applications, Obróbka Plastyczna Metali XVII (4) (2006) 21–26.
• [4] R. Kawalla, M.Oswald, C. Schmidt, M. Ullmann, H.P. Vogt, N.D. Cuong, Development of a Strip-Rolling Technology for Mg Alloys Based on the Twin Roll Casting Process, in: Proceedings of the 137th Annual Meeting & Exhibition, New Orleans, USA, 2008c.
• [5] S. Thamizhmanii, S. Saparudin, S. Hasan, Analyses of surface roughness by turning process using Taguchi method, Journal of Achievements in Materials and Manufacturing Engineering 20 (2007) 503–506.
• [6] A. Maleki, A. Shafyei, B. Niroumand, Effects of squeeze casting parameters on the microstructure of LM13 alloy, Journal of Materials Processing Technology 209 (2009) 3790–3797.
• [7] I. Asilturk, H. Akkus, Determining the effect of cutting parameters on surface roughness in hard turning using the Taguchi method, Measurement 44 (2011) 1697–1704.
• [8] S.S. Mahapatra, Parametric optimization of wire electrical discharge machining (WEDM) process using Taguchi method, Journal of the Brazilian Society of Mechanical Sciences and Engineering 28 (4) (2006) 422–429.
• [9] R.B. Raviraj Shetty, Study on surface roughness minimization in turning of DRACs using surface roughness methodology and Taguchi under pressured steam, jet approach, ARPN Journal of Engineering and Applied Sciences 3 (2008) 59–67.
• [10] R. Kawalla, M. Ullmann, M. Oswald, C. Schmidt, Properties of Strips and Sheets of Magnesium Alloy Produced by Casting-Rolling Technology, K.U. Kainer in: Proceedings of the 7th International Conference on Magnesium Alloys and Their Applications, Dresden, 2006b pp. 364–369.
• [11] R. Kawalla, M. Ullmann, Ch. Schmidt, J. Dembinska, H.P. Vogt, Properties of magnesium strips produced by twin-roll-casting and hot rolling, Materials Science Forum 690 (2011) 21–24.