Validation of the metrological model of coordinate measuring arm using multifeature check

• Autorzy: Gromczak K. , Ostrowska K. , Owczarek D. , Sładek J.

Identyfikatory

DOI

10.12913/22998624/60798

• Języki publikacji: EN

Abstrakty

EN

The article presents the validation research scheme of metrological model of coordinate measuring arm (CMA) using multifeature check. The scheme shows the comparison of the calibration results of the check using selected coordinate methods and criteria of validation. The comparison shows the insignificance of differences between the obtained results of both: metrological model of CMA and multi-position method. It evidently proves the correctness of the development of metrological model of CMA. The use of appropriate quality multifeature check also had a significant impact on the results. This check is now the most accurate measurement length check and its use for this validation process was the most suitable.

Słowa kluczowe

EN

validation; metrological model; coordinate measuring arms

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2015
• Tom: Vol. 9, nr 28
• Strony: 120--124
• Opis fizyczny: Bibliogr. 12 poz., fig., tab.

Twórcy

autor

Gromczak K.

• Laboratory of Coordinate Metrology, Faculty of Mechanical Engineering, Cracow University of Technology, Jana Pawła II 37, 31-864 Kraków, Poland

autor

Ostrowska K.

• Laboratory of Coordinate Metrology, Faculty of Mechanical Engineering, Cracow University of Technology, Jana Pawła II 37, 31-864 Kraków, Poland

autor

Owczarek D.

• Laboratory of Coordinate Metrology, Faculty of Mechanical Engineering, Cracow University of Technology, Jana Pawła II 37, 31-864 Kraków, Poland

autor

Sładek J.

• Laboratory of Coordinate Metrology, Faculty of Mechanical Engineering, Cracow University of Technology, Jana Pawła II 37, 31-864 Kraków, Poland

Bibliografia

• 1. Gąska A., Krawczyk M., Kupiec R., Ostrowska K., Gąska P., Sładek J.: Modeling of the residual kinematic errors of Coordinate Measuring Machines using Laser Tracer system. International Journal of Advanced Manufacturing Technology, 2014, DOI: 10.1007/s00170-014-5836-1.
• 2. Ostrowska K., Szewczyk D., Sładek J.: Determination of operator’s impact on the measurement done using coordinate technique. Advances in Science and Technology Research Journal, 7(20), 2013, 16–21, DOI: 10.5604/20804075.1073045.
• 3. Ostrowska K., Gąska A., Sładek J.: Determining the uncertainty of measurement with the use of a Virtual Coordinate Measuring Arm. International Journal of Advanced Manufacturing Technology, 2013, DOI: 10.1007/s00170-013-5486.
• 4. Sładek J., Ostrowska K., Gąska A.: Modeling and identification of errors of coordinate measuring arms with the use of a metrological model. Measurement, 46, 2013, 667–679, DOI: 10.1016/j. measurement.2012.08.026.
• 5. Sładek J., Ostrowska K., Gacek K., Bryndza M.: Designation of operator impast on errors of measurements realized by coordinate measuring arm. In: J. Sładek, W. Jakubiec (Eds.) Advances in Coordinate Metrology, Bielsko-Biała 2010, 130–137.
• 6. Sładek J., Ostrowska K., Gąska A.: Wirtualne współrzędnościowe ramie pomiarowe. Pomiary – Automatyka – Kontrola, 54(01), 2010.
• 7. Sładek J., Ostrowska K., Gąska A., Gacek K., Kmita A.: Model matematyczny opisu dokładności współrzędnościowych ramion pomiarowych. W: J. Gawlik (red.) Innowacyjne systemy produkcyjne. Monografia, 2009.
• 8. Sładek J., Ostrowska K., Gacek K.: Kinematic metrological model of the coordinate measuring arm (MCMA). In: XIX World Congress Fundamental and Applied Metrology IMEKO, Lisbon, Portugal 2009.
• 9. Sładek J.: Dokładność pomiarów współrzędnościowych. Wydawnictwo Politechniki Krakowskiej, Kraków 2011.
• 10. Kacker R.N., Kessel R., Sommer K.D., Bian X.: Comparison of statistical consistency and metrological compatibility. In: XIX World Congress Fundamental and Applied Metrology IMEKO, Lisbon, Portugal, 2009, 6–11.
• 11. Kacker R.N., Kessel R., Sommer K.D.: Assesing differences between results determined according to the Guide of Expression of Uncertainty in Measurement. Journal of Research of the National Institute of Standards and Technology, 115, 2010, 453–459.
• 12. Kacker R.N., Kessel R., Sommer K.D.: Metrological compatibility and statistical consistency. In: 10th International Symposium on Measurement and Quality Control, September 5-9, 2010.