Tytuł artykułu
Wybrane pełne teksty z tego czasopisma
Identyfikatory
Warianty tytułu
Ilościowa ocena sygnału prądów wirowych od wad w austenitycznych rurkach wymienników ciepła
Języki publikacji
Abstrakty
The research discussed in the article involved the analysis of impedance characteristics originating from various non-standard defects detected in the material of an austenitic tube. Research-related test results were obtained when scanning a tube made of steel 316, using an internal probe and a MultiScan 5800 device. The tests involved the use of the classical ECT vortex current method applied to examine both the tube containing artificial defects, simulating the most common defects in industrial heat exchanger tubular inserts, and reference tubes containing standard defects. The non-standard defects (created artificially) simulated combinations of cracks, pits or other defects formed as a result of exposure to aggressive chemical and mechanical factors present in industrial conditions. The tests involved the scanning of the entire length of the tube at a constant rate. The tests were performed using a transient probe recording electrical impedance changes in a relative mode and in an absolute mode. The interpretation of results related to the non-standard defects was based on a comparison with the results obtained in relation to the standard reference defects. Values obtained in relation to the non-standard defects enabled, among other things, the identification of their volume and position in relation to the measurement probe. In most cases it was not possible to interpret the geometry of a given defect. The foregoing could be achieved using other non-destructive testing techniques.
Dokonano oceny charakterystyk impedancyjnych pochodzących od różnych wad w materiale rury austenitycznej. Wskazania te otrzymano podczas badania rury ze stali 316 sondą wewnętrzną z wykorzystaniem aparatu MultiScan 5800. Zastosowano klasyczną metodę prądów wirowych ECT, badając zarówno rurę ze sztucznymi wadami symulującymi najczęściej spotykane uszkodzenia wkładów rurowych wymienników ciepła, jak również rury referencyjne, z i wadami standardowymi. Wytworzone sztucznie niestandardowe wady miały na celu odwzorowanie spotykanych w diagnostyce przemysłowej kombinacji pęknięć, wżerów lub innych ubytków powstałych w wyniku oddziaływań mechanicznych oraz działania agresywnych czynników chemicznych. Badania polegały na skanowaniu rury ze stałą prędkością, przy użyciu sondy przelotowej rejestrującej zmiany impedancji elektrycznej w trybie względnym i trybie absolutnym. Interpretacja uzyskanych wyników, dla wad niestandardowych, była oparta na analizie porównawczej z wynikami uzyskanymi dla standardowych próbek referencyjnych. Otrzymane wartości dla wad niestandardowych umożliwiły ich scharakteryzowanie, tj. określenie ich objętości oraz położenia względem sondy pomiarowej. W większości przypadków nie była możliwa interpretacja geometrii wady, a co jest możliwe przy zastosowaniu innych technik badań nieniszczących.
Czasopismo
Rocznik
Tom
Strony
59--65
Opis fizyczny
Bibliogr. 4 poz., rys., tab.
Twórcy
autor
- Institute of Fundamental Technological Research - Polish Academy of Sciences, Warszawa
autor
- Warsaw University of Technology, Faculty of Materials Science and Engineering, Warszawa
autor
- Warsaw University of Technology, Faculty of Materials Science and Engineering, Warszawa
Bibliografia
- [1] http://www.vikinginspection.co.uk/services/heat-exchangers.
- [2] Schwartz M.: Four Types of Heat Exchanger Failures. Plant Engineering, 1982, no. 12.
- [3] Zbroińska-Sczechura E., Dobosiewicz J.: Uszkodzenia i diagnostyka wymienników ciepła w elektrociepłowniach. www.elektroenergetyka.pl, December 2004, pp. 14-16.
- [4] www.olympusndt.com.
Uwagi
PL
Wersja polska artykułu w wydaniu papierowym s. 66-72.
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-348b7a8c-408f-4cbe-a877-c3e8b20e5275