The Impact of Crushed Rock Spoil on Pitting Corrosion of Selected Stainless Steels

• Autorzy: Krakowiak S. , Kierepa S.

Identyfikatory

DOI

10.24425/amm.2019.130136

• Języki publikacji: EN

Abstrakty

EN

The paper presents the results of the pitting resistance investigations of selected stainless steels in the chloride environment and the simultaneous impact of erosive factors using the cyclic polarization technique. Additionally, using electrochemical techniques, ie: electrochemical impedance spectroscopy (EIS) and measurement of corrosion potential, the behavior of the passive layer of selected stainless steels in the environment of chlorides and erosion was examined. On the basis of the obtained results, the resistance of stainless steels 1.4301 and 1.4404 was found, both on the effect of chloride ions and erosive factors in the studied systems. Both tested steels are susceptible to pitting corrosion. It was found that a good measure of erosive impact on stainless steel is both impedance spectrum analysis and continuous monitoring of the corrosion potential of steel.

Słowa kluczowe

EN

corrosion; erosion; pitting corrosion; EIS

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2019
• Tom: Vol. 64, iss. 4
• Strony: 1627--1632
• Opis fizyczny: Bibliogr. 22 poz., fot., rys., tab.

Twórcy

autor

Krakowiak S.

• Gdansk University of Technology, Faculty of Chemistry, Department of Electrochemistry, Corrosion and Materials Engineering 11/12 Gabriela Narutowicza Str., 80-233 Gdańsk, Poland

autor

Kierepa S.

• KGHM Polska Miedź S.A.

Bibliografia

• [1] P. A. Schweitzer, Fundamentals of Corrosion Mechanisms, Causes and Preventative Methods, Taylor and Francis Group, 2010.
• [2] S. Dudka, D. C. Adriano, J. Environ. Qual. 26 (3) 590-602 (1997).
• [3] M. Y. Naz, S. A. Sulaiman, et al., Measurement. 106 (2) 203-210 (2017).
• [4] C. G. Duan, V. Y. Karelin (ed.), Abrasive erosion & corrosion of hydraulic machinery, Imperial Colege Press, 2002.
• [5] G. B. Stachowiak, M. Salasi, W.D.A. Rickard, G. W. Stachowiak, Corrosion Science 111, 690-702 (2016).
• [6] H.J.D. Bruyn, Int. J. Press. Vessel. Pip. 66 (1-3) 293-303 (1996).
• [7] A. K. Mahmood, A. A. Khadom, J. Fail. Anal. and Preven. 16 (6) 1071-1081 (2016).
• [8] R. V. Pludek, Design and Corrosion Control, Palgrave, 2014.
• [9] K. Żakowski, Anti-corrosion Methods and Materials 58 (4), 167-172 (2011).
• [10] K. Żakowski, M. Szociński et al., Anti-corrosion Methods and Materials 60 (2), 95-99 (2013).
• [11] C. C. Nathan (ed.), Corrosion Inhibitors, NACE, Houston, Texas.
• [12] M. M. Lachowicz, M. B. Lachowicz, Archives of Metalurgy and Materials 60 (4), 2657-2661 (2015).
• [13] S. Esmailzadeh, M. Aliofkhazraei, H. Sarlak, Protection of Metals and Physical Chemistry of Surfaces 54 (5), 976-989 (2018)
• [14] A. R. Nuradityatama, M. F. Rendi, S. Setiawan, International Journal of Mechanical Engineering and Robotics Research 6 (6), 512-518 (2017).
• [15] G. Monrrabal, B. Ramírez-Barat, A. Bautista, F. Velasco, E. Cano, Metals 500 (8), 1-16 (2018).
• [16] Xiu-qing Xu et. al, Int. J. Electrochem. Sci., 13 (10), 4298-4308 (2018).
• [17] L. Freire, M. J. Carmezim, M.G.S. Ferreira, M. F. Montemor, Electrochim. Acta, 55 (21), 6174-6181 (2010).
• [18] C. M. Abreu, M. J. Cristobal, R. Losada, X. R. Nóvoa, G. Pena, M. C. Perez, Electrochim. Acta 51 (8-9), 1881-1890 (2006).
• [19] B. A. Boukamp, Solid State Ionics 20 (1) 31 (1986).
• [20] G. S. Frankel, N. Sridhar, Materials Today 11 (10), 39-44 (2008).
• [21] M. P. Ryan, D. E. Williams, R. J. Chater, B. M. Hutton, D. S. McPhail, Nature 415 (2), 770-77 (2002).
• [22] K. Darowicki, S. Krakowiak, Electrochimica Acta 42 (16), 2559-2562 (1994).