Analysis of the composite material behaviour subjected to dynamic bending using the hopkinson bar

• Autorzy: Massaq A. , Rusinek A. , Klósak M. , Boulouz A. , Koutti L.
• Języki publikacji: EN

Abstrakty

EN

The aim of this study is to propose an experimental approach supported by an analytical analysis for polymer materials under dynamic loading. The experimental technique of Hopkinson split pressure bar is used which allows for high impact velocities. The specimens are subjected to the three-point bending and the efficiency of the experimental technique is proved. During quasi-static and dynamic bending tests, the rupture mode is described and the evolution of the energy and the ultimate stresses as a function of the initial impact velocity is discussed. In addition, the critical impact velocity estimated above an important change in the rupture mode is observed. In order to better describe the physical phenomena encountered during the three-point bending impact, the analysis is supported by a rheological model based on a mass-spring system.

Słowa kluczowe

EN

impact velocity; three-point bending; woven composite; dynamic behaviour; shock; Hopkinson bar

PL

prędkość zderzenia; kompozyt; pręt Hopkinsona

• Wydawca: Instytut Podstawowych Problemów Techniki PAN
• Czasopismo: Engineering Transactions
• Rocznik: 2016
• Tom: Vol. 64, iss. 1
• Strony: 115--131
• Opis fizyczny: Bibliogr. 20 poz., rys., tab., wykr.

Twórcy

autor

Massaq A.

• Ecole Nationale des Sciences Appliqu´ees Laboratory OSCARS Avenue Abdelkrim Khattabi, 40000, Gu´eliz-Marrakech, Morocco
• Ibn Zohr University – Faculty of Sciences Agadir Laboratory LABSIV BP. 8106 Quartier Dakhla, Agadir, Morocco

autor

Rusinek A.

• National Engineering School of Metz ENIM Laboratory of Mechanics, Biomechanics, Polymers and Structures – LaBPS, EA 4632 1 route d’Ars Laquenexy, CS 65820 57078 METZ Cedex 3, France

autor

Klósak M.

• Universiapolis, Ecole Polytechnique d’Agadir Bab Al Madina, Quartier Tilila, Agadir, Morocco
• The International University of Logistics and Transport in Wrocław Sołtysowicka 19B, 51-168 Wrocław, Poland

autor

Boulouz A.

• Ibn Zohr University – Faculty of Sciences Agadir Laboratory LABSIV BP. 8106 Quartier Dakhla, Agadir, Morocco

autor

Koutti L.

• Ibn Zohr University – Faculty of Sciences Agadir Laboratory LABSIV BP. 8106 Quartier Dakhla, Agadir, Morocco

Bibliografia

• 1. Massaq A., Rusinek A., Klósak M., New experimental technique for dynamic bending of composite materials, Engineering Transactions, 62(3): 269–289, 2014.
• 2. Charpy G., Essay on the metals impact bend test of notched bars, Memory & Reports from the Society of Civil Engineers of France, 1901.
• 3. Fazal A., Fancey K.S., Viscoelastically prestressed polymeric matrix composites – effects of test span and fibre volume fraction on Charpy impact characteristics, Composites Part B: Engineering, 44(1): 472–479, 2013.
• 4. Hopkinson B., A method of measuring the pressure produced in the detonation of explosives or by impact of bullet, Philosophical Transactions A, 213, pp. 437–456, 1914.
• 5. Massaq A., Rusinek A., Klósak M., Method for determination of the dynamic elastic modulus for composite materials, Engineering Transactions, 61(4): 301–315, 2013.
• 6. Klepaczko J.R., An experimental technique for shear testing at high and very high strain rates. The case of mild steel, International Journal of Impact Engineering, 15(1): 25–39, 1994.
• 7. Klepaczko J.R., Matysiak S.J., Analysis of longitudinal impact on semi-infinite circular bars and tubes, Appendix No 2, The Final Technical Report Contract DAJA 45-90-C- 0052, Metz, October, 1992.
• 8. Williams J.G., Adams G.C., The analysis of instrumented impact tests using a massspring model, International Journal of Fracture, 33(3): 209–222, 1987.
• 9. Williams J.G., The analysis of dynamic fracture using lumped mass spring models, International Journal of Fracture, 33(1): 47–59, 1987.
• 10. Williams J.G., Tropsa V., MacGillivray H., Rager A., Dynamic correction factors for K and G in high rate, SENB, impact tests, International Journal of Fracture, 107(3): 259–278, 2001.
• 11. Kobayashi T., Analysis of impact properties of 4533 steel for nuclear reactor pressure vessel by instrumented impact test, Engineering Fracture Mechanics, 19(1): 49–65, 1984.
• 12. Effendi R., Failure mechanisms analysis under compression of unidirectional carbon/epoxy composites and micromechanical modeling, PhD thesis, ENSAM, 1993.
• 13. Golovoy A., Influence of velocity on the impact strength of glass reinforced polypropylene, Polymer Composites, 7(6): 405–412, 1986.
• 14. Yokoyama T., Kishida K., A novel impact three-point bend test method for determining dynamic fracture-initiation toughness, Experimental Mechanics, 29(2): 188–194, 1989.
• 15. Hanus J.-L., Magnain B., Durand B., Rodriguez J.A., Bailly P., Processing dynamic split Hopkinson three-point bending test with normalized specimen of quasi-brittle material, Mechanics & Industry, 13(6): 381–393, 2012.
• 16. Jiang F., Vecchio K.S., Hopkinson bar loaded fracture experimental technique: a critical review of dynamic fracture toughness tests, Applied Mechanics Reviews, 62(6): 060802-1– 060802-39, 2009.
• 17. Delvare F., Hanus J.-L., Bailly P., A non-equilibrium approach to processing Hopkinson bar bending test data: application to quasi-brittle materials, International Journal of Impact Engineering, 37(1): 1170–1179, 2010.
• 18. Govender R.A., Langdon G.S., Nurick G.N., Cloete T.J., Impact delamination testing of fibre reinforced polymers using Hopkinson pressure bars, Engineering Fracture Mechanics, 101: 80–90, 2013.
• 19. Nazarenko E., Fracture behavior of a ceramic fiber reinforced glass-ceramic matrix composite under both static and dynamic loadings, PhD Thesis of the Ecole Centrale de Paris, 1992.
• 20. Pignon A., Mathieu G., Richomme S., Margot J.M., Delvare F., Modified split Hopkinson pressure bars for dynamic bending and shear tests, Journal of Physics IV France, 134: 725–730, 2006.

Uwagi

PL

Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę.