Surface topography analysis of precision assemblies of fuel injector nozzles

• Autorzy: Miszczak A. , Labuda W. , Grondecki M.

Identyfikatory

DOI

10.5604/12314005.1130483

• Języki publikacji: EN

Abstrakty

EN

Precision surface assemblies can be found in the two locations in a fuel system of a diesel engine. These parts are the pumping section in an injection pump and the injector nozzles. In this paper the authors present the results of surface topography measurements of precise surface assemblies of some fuel injectors. The measurements have been made with the atomic force microscope (AFM) NT-206. The results of surface topography measurements were presented in the form of 2D and 3D images and also as surface roughness profiles in some selected cross-sections of the investigated surfaces. It has been also shown cumulative roughness height distribution and roughness height distribution as well as Minkowski volume (first Minkowski functional). After scanning the surface on the atomic force microscope, the obtained data were processed with the SurfaceXplorer ® 1.311 and Gwyddion 2.35 software. The study concerned some new injector nozzles and also injector nozzles after a certain time of operation. The side and the conical precise surface assembly of the injector nozzle body and needle were tested. The atomic force microscope NT-206 allows to perform a surface scan of the sample with maximum dimensions of 32x32 μm and a maximum height of roughness ± 1 μm. Scanned area was divided into 256x256 measurement points, while the measurement was carried out in a static (contact) mode. The results presented in this paper also includes the calculated values of Ra, Sa (roughness average) and Rq, Sq (root mean square roughness) surface roughness parameters and the value of the skewness Ssk (Rsk), kurtosis Sku (Rku) and maximum distance between the lowest valley and the highest peak of investigated surface – Rt. The obtained data allow evaluating the degree and type of wear of tested surfaces on the micro-scale.

Słowa kluczowe

EN

Atomic Force Microscope; surface topography; roughness; plunger; barrel; injector pump pumping section

• Wydawca: Łukasiewicz Research Network - Institute of Aviation ; European Science Society of Powertrain and Transport KONES Poland ; Wydawnictwo Instytutu Technicznego Wojsk Lotniczych
• Czasopismo: Journal of KONES
• Rocznik: 2014
• Tom: Vol. 21, No. 4
• Strony: 353--360
• Opis fizyczny: Bibliogr. 11 poz., rys.

Twórcy

autor

Miszczak A.

• Gdynia Maritime University, Faculty of Marine Engineering Morska Street 81-87, 81-225 Gdynia, Poland tel.:[phone], fax: [phone]

autor

Labuda W.

• Gdynia Maritime University, Faculty of Marine Engineering Morska Street 81-87, 81-225 Gdynia, Poland tel.:[phone], fax: [phone]

autor

Grondecki M.

• Gdynia Maritime University, Faculty of Marine Engineering Morska Street 81-87, 81-225 Gdynia, Poland tel.:[phone], fax: [phone]

Bibliografia

• [1] Atomic Force Microscope NT-206 Operating Manual, A. V. Lykov Institute of Heat and Mass Transfer, Minsk 2010.
• [2] Bharat Bhushan, Modern Tribology Handbook, CRC Press, London-New York-Washington, D.C.2001.
• [3] Dong-Hyeok Lee, Nahm-Gyoo Cho, Assessment of surface profile data acquired by a stylus profilometer, Measurement Science and Technology, Vol. 23, No. 10, 105601, doi:10.1088/0957-0233/23/10/105601, 12 p., 2012.
• [4] Górecka, R., Polański, Z., Metrologia warstw wierzchniej, WNT, Warszawa 1983.
• [5] Krępeć, T., Falkowski, H., Obsługa i naprawa aparatury paliwowej silników wysokoprężnych, Wydawnictwa Komunikacji i Łączności, Warszawa 1973.
• [6] Matuszewski, M., Kierunkowość struktury geometrycznej powierzchni w transformacji warstwy wierzchniej, Rozprawa doktorska, Bydgoszcz 2013.
• [7] Oczoś, K, Liubimov, V., Rozważania nad istotnością parametrów struktury geometrycznej powierzchni w układzie 3D, Mechanik, R. 81, Nr 3, s. 129-130, 2008.
• [8] Rodríguez-Valverde, M. A., Ramón-Torregrosa, P. J., Cabrerizo-Vílchez, M. A., Estimation of percolation threshold of acid-etched titanium surfaces using Minkowski functionals,Microscopy: Science, Technology, Applications and Education (Microscopy Book Series),Ed. A. Méndez-Vilas, J. Diaz. Formatex Research Center, Vol. 3, No. 4, pp. 1978-1983, 2010.
• [9] Tomasik, J., Badania porównawcze parametrów mikrogeometrii powierzchni w układzie 2D i 3D, Mechanik, R. 82, Nr 8-9, s. 722-724, 2003.
• [10] Whitehouse, D. J., Handbook of Surface and Nanometrology, University of Warwick, Institute of Physics Publishing, Bristol and Philadephia 2003.
• [11] www.olympus-ims.com/en/knowledge/metrology/roughness/3d_parameter/, 2014.