PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Microstructural study of failure phenomena in WC 94%-Co 6% hard metal alloy tips of radial picks

Treść / Zawartość
Identyfikatory
Warianty tytułu
Języki publikacji
EN
Abstrakty
EN
An excellent combination of hardness, strength, stiffness and high melting point has proved the WC-Co as an ideal material for tools that are used for metal cutting, coal mining, oil drilling, etc. The ongoing research in WC-Co is focussed on enhancing its wear resistant properties as much as possible. For the purpose, many attempts have been made to study the tribological behaviour of WC-Co for a long time. Researchers have used various grades of WC-Co in different working environments and accordingly they have characterized the wear phenomena involved there within. In this direction of research, the present paper makes an attempt to understand various wear behaviours in WC 94%-Co 6% hard metal alloy. WC-Co was used as a tip of the coal cutting tool named radial pick. Two radial picks have been taken for critical analysis through field emission scanning electron microscopy (FESEM) attached with energy dispersive X-ray spectroscopy (EDS). In this work, the failure behaviours in the tools have been divided into five categories: (1) Abrasion on individual grain; (2) Corrosion in carbide grains; (3) Fragmentation and removal of WC grains; (4) Pores in WC grains; and (5) Coal and rock embedding. The most possible reasons behind each failure phenomenon have been explained comprehensively with the help of high-resolution microscopic images. However, it is usually observed that, initially, the tool gets minor cracks due to sudden impact. These cracks provide a path to the rock and coal particles to get entrenched inside the microstructure of cemented carbide. Finally, the intermixed external elements degrade the binder content (i.e. cobalt) and the tool becomes useless.
Słowa kluczowe
Twórcy
autor
  • Department of Mechanical Engineering, Jaypee University of Engineering and Technology, Guna 473226, India
  • Department of Mechanical Engineering, Indian Institute of Technology (ISM), Dhanbad 826004, India
autor
  • Department of Mechanical Engineering, National Institute of Science and Technology, Berhampur 761008, India
autor
  • Faculty of Manufacturing Technologies, Technical University of Kosice with a Seat in Presov, 080 01, Slovakia
autor
  • Opole University of Technology, 76 Proszkowska St., 45-758 Opole, Poland
autor
  • Faculty of Mechanical Engineering and Management, Poznan University of Technology, ul. Piotrowo 3, 60-965 Poznan, Poland
Bibliografia
  • 1. Altinoluk S., Investigations into the Effects of Tungsten Carbide Composition and Geometry on the Durability of Rock Excavation Tools, Ph.D. Thesis, University of Newcastle upon Tyne, 1981.
  • 2. Aylward G., Friendly T. SI Chemical Data. P. Storer, Ed, Wiley, Sydney, 1994.
  • 3. Beste U. On the Nature of Cemented carbide Wear in Rock Drilling. Comprehensive summary of Uppasala dissertations from the faculty of Sc. and Tech., Acta Universitatis Upsaliensis, 2004.
  • 4. Beste U., Hartzell T., Engqvist H., Axén N., Surface damage on cemented carbide rock-drill buttons. Wear, 249, 2001, 324–329.
  • 5. Beste U., Jacobson S. Micro scale hardness distribution of rock types related to rock drill wear. Wear, 254, 2003, 1147–54.
  • 6. Beste U., Jacobson S., Friction between a cemented carbide rock drill button and different rock types. Wear, 253, 2002, 1219-1221.
  • 7. Beste U., Jacobson S., Hogmark S., Rock penetration into cemented carbide drill buttons during rock drilling. Wear, 264, 2008, 1142–51.
  • 8. Bilgin N., Copur H., Balci C., Mechanical excavation in mining and civil industries. CRC Press, Boca Raton, 2013, 103–123.
  • 9. Bilgin N., Demircin M.A., Copur H., Balci C., Tuncdemir H., Akcin N., Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results. Int J Rock Mech Min Sci, 43, 2006, 139–156.
  • 10. Brookes K.J.A., Hardmetals and Other Hard Materials. International Carbide Data, 1992.
  • 11. Cigla V., Ozdemir L., Computer modelling for improved production of mechanical excavators. In: Proc soc mining metall explor (SME) ann mtg, Salt Lake City, 2000, p. 12.
  • 12. Demou S.G., Olson R.C., Wingquist C.F., Determination of bit forces encountered in hard rock cutting for application to continuous miner design. Report of investigations, US Bur Mines, RI 8748, 1983.
  • 13. Dewangan S., Chattopadhyaya S., Characterization of wear mechanisms in distorted conical picks after coal cutting. Rock Mech Rock Eng, 49, 2016, 225-242.
  • 14. Dewangan S., Chattopadhyaya S., Critical analysis of wear mechanisms in cemented carbide. Journal of Materials Engineering and Performance, 24, 2015, 2628–2636.
  • 15. Dewangan S., Chattopadhyaya S., Hloch S., Critical damage analysis of WC-Co tip of conical pick due to coal excavation in mines. Advances in Materials Science and Engineering, 2015, 2015, 7 pages. http://dx.doi.org/10.1155/2015/292046
  • 16. Dewangan S., Chattopadhyaya S., Hloch S., Wear assessment of conical pick used in coal cutting operation. Rock Mech Rock Eng, 48, 2015, 2129–2139.
  • 17. Echtenkamp A.L., Combating Corrosion/Wear with the Hard Carbide Alloys. Proc. ASLE/Asme Lubrication Conf., Minneapolis, 1978.
  • 18. Feldshtein E., Józwik J., Legutko S., The influence of the conditions of emulsion mist formation on the surface roughness of AISI 1045 steel after finish turning. Advances in Science and Technology Research Journal, 10, 2016, 144–149.
  • 19. Fish B.G., Guppy G.A., Ruben J.T., Abrasive wear effects in rotary rock drilling. Trans. Mining Metall., 68, 1959, 357–383.
  • 20. Fowell J., Hekimoglu O.Z., Altinoluk S., Drag tools employed on shearer drums and roadheaders. In: Proc 10th Turkish mining cong, Ankara, 1987, 529–550.
  • 21. Hekimoglu O.Z., Investigations into performance of point-attack and radial type rock and coal-cutting picks. Trans Inst Min Metall, 107, 1998, 55–9.
  • 22. Hurt K.G., Evans I., Point attack tools: an evaluation of function and use for rock cutting. Min Engr, March, 1981, 673–5.
  • 23. Józwik J., Czwarnowski M., Angular positioning accuracy of rotary table and repeatability of five-axis machining centre DMU 65 monoblock. Advances in Science and Technology Research Journal, 9, 2015, 89–95.
  • 24. Józwik J., Semotiuk L., Kuric I., Diagnostic of CNC lathe with QC 20 ballbar system. Advances in Science and Technology Research Journal, 9, 2015, 96–102.
  • 25. Khair A.W., Research and Innovations for Continuous Miner’s Cutting Head for Efficient Cutting process of rock/coal. Department of Mining Engineering, West Virginia University, Morgantown, USA. 17* International Mining Congress and Exhibition of Turkey- IMCET, 2001.
  • 26. Kindermann P., Schlund P., Sockel H.G., Herr M., Heinrich W., Gorting K., Schleinkofer U., High- Temperature Fatigue of Cemented Carbides Under Cyclic Loads. Int. J. Refract. Metal Hard Mater., 17, 1999, 55–68.
  • 27. Lagerquist M., A study of the thermal fatigue crack propagation in WC–Co cemented carbide. Powder Metallurgy, 18, 1975, 71–88.
  • 28. Larsen-Basse J., Binder extrusion in sliding wear of WC-Co alloys. Wear, 105, 1985, 247–56.
  • 29. Larsen-Basse J., Wear of hard-metals in rock drilling: a survey of the literature. Powder Metall., 16, 1973, 1–32.
  • 30. Lee G.H., Kang S., Sintering of Nano-Sized WC-Co Powder Produced by a Gas Reduction-Carburization Process. J. Alloy. Compd., 419, 2006, 281–289.
  • 31. Maidl B., Schmid L., Ritz W., Herrenknecht M. Hard Rock Tunnel Boring Machines. Ernst & Sohn, Berlin, 2008.
  • 32. Mary D., Gonseth D.R., A new look at carbide tool life. Wear, 165, 1993, 9-17.
  • 33. Milman Y.V., Luyckx S., Northrop I.T., Influence of Temperature, Grain Size and Cobalt Content on the Hardness of WC-Co Alloys. Int. J. Refract. Met. Hard Mater, 17, 1999, 39–44.
  • 34. Mukhopadhyay A., Basu B., Recent developments on WC-based bulk composites. J. Mater Sci, 46, 2011, 571-589.
  • 35. Plis N., Wingquist C.F., Roepke W., Preliminary evaluation of the relationship of bit wear to cutting distance, forces, and dust using selected commercial and experimental coal- and rock-cutting tools. Report of Investigations, US Bur Mines, RI 9193, 1988.
  • 36. Rajput R.K., A Text Book of Manufacturing Technology: (Manufacturing Processes), Firewall Media, 2007, p 407.
  • 37. Roadheaders. http://www.mitsuimiike.co.jp/english/product/excavator/rh/index.html
  • 38. Sandvik Mineral and Ground Engineering Tools: (Product Catalogue). www.miningandconstruction.sandvik.com
  • 39. Stjernberg K.G., Fisher U., Hugoson N.I., Wear mechanisms due to different rock drilling conditions. Powder Metall., 18, 1975, 89–106.
  • 40. Stolarski T.A., Tribology in Machine Design. Butterworth-Heinemann, Oxford, 2000.
  • 41. Sundae L.S., Myren T.A., In situ comparison of radial and point attack bits. Report of investigations, US Bur Mines, RI 9127, 1987.
  • 42. Swick K.J., Stachowiak G.W., Batchelor A.W., Mechanism of wear of rotary-percussive drilling bits and the effect of rock type on wear. Tribol Int, 25, 1992, 83–8.
  • 43. Wang J., Wang H., Wang H. et al., Failure analysis of WC-3.5wt%Co cemented carbides in mining Applications. J. Wuhan Univ. Technol.- Mat. Sci. Edit., 30, 2015, 1279-85. DOI: 10.1007/s11595- 015-1308-1
  • 44. Wood G.A., Quality Control in the Hard Metal Industry. Powder Metall., 13, 1970, 338–368.
  • 45. Yilmaz N.G., Yurdakul M., Goktan R.M., Prediction of radial bit cutting force in high-strength rocks using multiple linear regression analysis. Int J Rock Mech Min Sci, 44, 2007, 962–970.
  • 46. Zum Gahr K.H., Microstructure and wear of materials. Elsevier, Amsterdam, 1987.
Uwagi
Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę (zadania 2017)
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-2aa4b65a-4998-4c92-a472-ee5434e12db7
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.