Dimethicone-assisted laser cutting of CFRP hole

• Autorzy: Chen Xinghua , Li Wenyuan , Rong Youmin , Zhang Guojun , Chen Long , Huang Yu

Identyfikatory

DOI

10.1007/s43452-022-00508-3

• Języki publikacji: EN

Abstrakty

EN

When cutting carbon fiber reinforced polymer (CFRP) plate with UV nanosecond laser, the surface heat-affected zone (HAZ) such as fiber exposure and carbonization will occur, which affects the surface morphology and properties of CFRP. In this paper, dimethicone-assisted laser cutting technology is proposed. Compared with laser direct cutting, we found that dimethicone-assisted cutting has obvious advantages in cutting CFRP. Due to the heat transfer inhibition of dimethicone, there is almost no burning phenomenon of matrix materials. The orthogonal test method was used to study the three key process parameters (laser scanning speed, repetition frequency and concentric circle spacing) of dimethicone-assisted laser cutting CFRP. It is concluded that the HAZ width can be controlled at 38.70–54.77 μm with dimethicone, compared with the traditional direct machining (HAZ width: 109.64–439.13 μm). Under the optimal cutting parameters of laser scanning speed of 500 mm/s, repetition rate of 50 kHz and concentric circle spacing of 0.04 mm, the minimum HAZ is 38.70 μm, which is reduced by 85.89% (the HAZ width of laser direct machining is 274.37 μm).

Słowa kluczowe

EN

laser cutting; CFRP; dimethicone; heat-affected zone

PL

cięcie laserowe; przenoszenie ciepła; skanowanie laserowe

• Wydawca: Springer ; Wrocław University of Science and Technology
• Czasopismo: Archives of Civil and Mechanical Engineering
• Rocznik: 2022
• Tom: Vol. 22, no. 4
• Strony: art. no. e182, 2022
• Opis fizyczny: Bibliogr. 38 poz., rys., tab., wykr.

Twórcy

autor

Chen Xinghua

• State Key Lab of Digital Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan, China
• School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China

autor

Li Wenyuan

• State Key Lab of Digital Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan, China
• School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China

autor

Rong Youmin

• State Key Lab of Digital Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan, China
• School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
• Laser Manufacturing Institute, National Innovation Institute of Digital Design and Manufacturing, Wuhan, China

autor

Zhang Guojun

• State Key Lab of Digital Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan, China
• School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China

autor

Chen Long

• State Key Lab of Digital Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan, China
• School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China

autor

Huang Yu

• State Key Lab of Digital Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan, China
• School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China

Bibliografia

• [1] An Q, Chen J, Ming W, Chen M. Machining of SiC ceramic matrix composites: a review. Chin J Aeronaut CJA. 2020;1683:1–28.
• [2] Wenyuan L, Yu H, Xinghua C, et al. Study on laser drilling induced defects of CFRP plates with different scanning modes based on multi-pass strategy. Opt Laser Technol. 2021;144:107400.
• [3] Ji LB, Zhu XW, Ding JP, et al. Progress in research and application on carbon fiber reinforced polymer in passenger cars. Automotive Digest. 2020;9:17–22.
• [4] Zhang WQ, Li ZhC, Wu TY, et al. Molecular simulation research and development of cross-linked structure and macroscopic properties of epoxy resin and its composites. Acta Mater Compos Sin. 2019;36(2):269–76.
• [5] Meltem AK, Hasan G. A review on machinability of carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP) composite materials. Defence Technol. 2018;14(4):318–26.
• [6] Wenyuan L, Guojun Z, Yu H, et al. UV laser high-quality drilling of CFRP plate with a new interlaced scanning mode. Compos Struct. 2021;273:114258.
• [7] Swan S, Bin Abdullah MS, Kim D, et al. Tool wear of advanced coated tools in cutting of CFRP. J Manuf Sci Eng Trans ASME. 2018;140:111018.
• [8] Zadafiya K, Bandhu D, Kumari S, et al. Recent trends in drilling of carbon fiber reinforced polymers (CFRPs): A state-of-the-art. review. J Manuf Process. 2021;69(1–4):47–68.
• [9] Phapale K, Singh R, Singh R. Comparative assessment of delamination control techniques in conventional drilling of CFRP. Procedia Manuf. 2020;48:123–30.
• [10] Sezer M, Ugur K, Mehmet B, et al. Cryogenic machining of carbon fiber reinforced plastic ( CFRP) composites and the effects of cryogenic treatment on tensile properties: A comparative study. Composites B. 2018;147:1–11.
• [11] Li M, Huang M, Jiang X, Kuo C-L, Yang X. Study on burr occurrence and surface integrity during slot milling of multi-directional and plain woven CFRPs. Int J Adv Manuf Technol. 2018;97(1–4):163–73.
• [12] Angelone R, Caggiano A, Nele L, et al. Optimal cutting parameters and tool geometry in drilling of CFRP/CFRP stack laminates for aeronautical applications. Procedia CIRP. 2021;99:398–403.
• [13] Kakinuma Y, Ishida T, Koike R, et al. Ultrafast feed drilling of carbon fiber-reinforced thermoplastics. In 15th Machining Innovations Conference for Aerospace Industry. Amsterdam, The Netherlands: Elsevier Science,2015:91–95.
• [14] Wu Y, Zhang G, Wang J, et al. The cutting process and damage mechanism of large thickness CFRP based on water jet guided laser processing. Opt Laser Technol. 2021;141(2): 107140.
• [15] Xu H, Hu J. Modeling of the material removal and heat affected zone formation in CFRP short pulsed laser processing. Appl Math Model. 2017;46:354–64.
• [16] Ge J. Research on principle and application of high pressure water Jet cutting Technology. China’s New Technol Prod. 2013;3:18.
• [17] Hou SJ, Bai JC, Liu XM, et al. Experimental investigation on discharge states characteristics of EDM. Aeronaut Manuf Technol. 2021;64(10):80–5.
• [18] Sambruno A, Baon F, Salguero J, et al. Kerf Taper defect minimization based on abrasive water-jet guided laser machining et machining of low thickness thermoplastic carbon fiber composites C/TPU. Materials. 2019;12(24):4192.
• [19] Habib S, Okada A. Influence of electrical discharge machining parameters on cutting parameters of carbon fiber-reinforced plastic. Mach Sci Technol. 2016;20(1/2):99–114.
• [20] Huang H, Zhigilei LV. Computational study of laser fragmentation in liquid: Phase explosion, inverse Leidenfrost effect at the nanoscale, and evaporation in a nanobubble. Sci China Phys Mech Astron. 2022. https://doi.org/10.1007/s11433-021-1881-8.
• [21] Heiderscheit T, et al. Keyhole cutting of carbon fiber reinforced polymer using a long-duration nanosecond pulse laser. Opt Lasers Eng. 2019;120:101–9.
• [22] Fischer F, Romoli L, Kling R. Laser-based repair of carbon fiber reinforced plastics. CIRP Ann Manuf Technol. 2010;59(1):203–6.
• [23] Hu J, Zhu DZ. Investigation of carbon fiber reinforced plastics machining using 355 nm picosecond pulsed laser. Appl Compos Mater. 2018;25(3):589–600.
• [24] Leone C, Genna S. Heat affected zone extension in pulsed Nd:YAG laser cutting of CFRP. Compos B Eng. 2018;140:174–82.
• [25] Lyu CY, Zhan RJ. Analysis and prediction of interlayer stress and strain of composites such as CFRP irradiated by laser. Mater Today Commun. 2021;28:102582.
• [26] El-Hofy MH, El-Hofy H. Laser beam machining of carbon fiber reinforced composites: a review. Int J Adv Manuf Technol. 2019;101:2965–75.
• [27] Oh S, Lee I, Park YB, et al. Investigation of cut quality in fiber laser cutting of CFRP. Opt Laser Technol. 2019;113:129–40.
• [28] Leone C, Papa I, Tagliaferri F, et al. Investigation of CFRP laser milling using a 30W Q-switched Yb∶YAG fiber laser: Effect of process parameters on removal mechanisms and HAZ formation. Composites A. 2013;55:129–42.
• [29] Mathew J, Goswami GL, Ramakrishnan N, et al. Parametric studies on pulsed Nd∶YAG laser cutting of carbon fibre reinforced plastic composites. J Mater Process Technol. 1999;89:198–203.
• [30] Tao N, Chen G, Yu T, et al. Dual-beam laser cutting process for thick carbon fiber reinforced plastic composites plates. J Mater Process Technol. 2020;281: 116590.
• [31] Sun D, Han F, Ying W, et al. Surface integrity of water jet guided laser machining of CFRP. Procedia CIRP. 2018;71:71–4.
• [32] Ouyang W, Jiao J, Xu Z, et al. Experimental study on CFRP cutting with the picosecond laser “double rotation” cutting technique. Opt Laser Technol. 2021;142(4): 107238.
• [33] Tangwarodomnukun V, Khamwiset K, Qi H. Investigation into laser machining of carbon fiber reinforced plastic in a flowing water layer. Int J Adv Manuf Technol. 2019;104(15):3629–45.
• [34] Leone C, Genna S, Tagliaferri V. Fibre laser cutting of CFRP thin sheets by multi-passes scan technique. Opt Lasers Eng. 2014;53:43–50.
• [35] Li M, Chen L, Yang X. A feasibility study on high-power fiber laser cutting of thick CFRP laminates using single-pass strategy. Opt Laser Technol. 2021;138: 106889.
• [36] Zhou L, Long YH, Jiao H, et al. Research advancement on laser processing carbon fiber reinforced plastics. Laser Technol. 2022;46(1):110–9.
• [37] Li ZL, Zheng HY, Lim GC, et al. Study on UV laser machining quality of carbon fibre reinforced composites. Compos A Appl Sci Manuf. 2010;41(10):1403–8.
• [38] Li W, Huang Y, Rong Y, et al. Analysis and comparison of laser cutting performance of solar float glass with different scanning modes. Front Mech Eng. 2021;16(1):97–110.

Uwagi

PL

Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023)