Effect of Microstructure and Unit Cell’s Geometry on the Compressive Mechanical Response of Additively Manufactured Co-Cr-Mo Sheet I-WP Lattice

• Autorzy: Park So-Yeon , Kim Kyu-Sik , AlMangour Bandar , Lee Kee-Ahn

Identyfikatory

DOI

10.24425/amm.2022.141087

• Języki publikacji: EN

Abstrakty

EN

Co-Cr-Mo based sheet I-WP lattice was fabricated via laser powder bed fusion. The effect of microstructure and the I-WP shape on compressive mechanical response was investigated. Results of compression test showed that yield strength of the sheet I-WP was 176.3 MPa and that of bulk Co-Cr-Mo (reference material) was 810.4 MPa. By applying Gibson-Ashby analytical model, the yield strength of the lattice was reversely estimated from that of the bulk specimen. The calculated strength of the lattice obtained was 150.7 MPa. The shape of deformed lattice showed collective failure mode, and its microstructure showed that strain-induced martensitic transformation occurred in the overall lattice. The deformation behavior of additively manufactured sheet I-WP lattice was also discussed.

Słowa kluczowe

EN

laser powder bed fusion; Co-Cr-Mo; sheet I-WP lattice; compressive mechanical response; strain-induced martensitic transformation

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2022
• Tom: Vol. 67, iss. 4
• Strony: 1525--1529
• Opis fizyczny: Bibliogr. 28 poz., fot., rys., wzory

Twórcy

autor

Park So-Yeon

• Inha University, Department of Materials Science and Engineering, Incheon, Korea

• https://orcid.org/0000-0001-6012-2294

autor

Kim Kyu-Sik

• Agency for Defense Development, Daejeon, Korea

• https://orcid.org/0000-0001-5649-8299

autor

AlMangour Bandar

• Interdisciplinary Research Center for Intelligent Manufacturing & Robotics, King Fahd University of Petroleum & Minerals, Dhahran, Saudi Arabi

• https://orcid.org/0000-0002-7855-2556

autor

Lee Kee-Ahn

• Inha University, Department of Materials Science and Engineering, Incheon, Korea

• https://orcid.org/0000-0003-2149-3871

Bibliografia

• [1] C. Pan, Y. Han, J. Lu, Appl. Sci. 10 (18), 6374 (2020).
• [2] L.J. Gibson, Mater. Sci. Eng. A 110, 1-36 (1989).
• [3] A.G. Evans, J.W. Hutchinson, M.F. Ashby, Prog. Mater. Sci. 43, 171-221 (1999).
• [4] T. Maconachie, M. Leary, B. Lozanovski, X. Zhang, M. Qian, O. Farugue, M. Brandt, Mater. Des. 183, 108137 (2019).
• [5] V.S. Deshpande, N.A. Fleck, M.F. Ashby, J. Mech. Phys. Solids 49, 1747-1769 (2001).
• [6] J. Zhou, P. Shrotriya, W.O. Soboyejo, Mech. Mater. 36, 723-737 (2004).
• [7] C. Yan, L. Hao, A. Hussein, S.L. Bubb, P. Young, D. Raymont, J. Mater. Process. Technol. 214, 856-864 (2014).
• [8] P. Heinl, L. Müller, C. Körner, R.F. Singer, F.A. Müller, Acta Biomater. 4, 1536-1544 (2008).
• [9] S. McKown, Y. Shen, W.K. Brookes, C.J. Sutcliffe, W.J. Cantwell, G.S. Langdon, G.N. Nurick, M.D. Theobald, Int. J. Impact Eng.
• 35, 795-810 (2008).
• [10] C. Yan, L. Hao, A. Hussein, D. Raymont, Int. J. Mach. Tool Manufact. 62, 32-38 (2012).
• [11] L. Mullen, R.C. Stamp, W.K. Brooks, E. Jones, C.J. Sutcliffe, J. Biomed. Mater. Res. B Appl. Biomater. 89B (2), 325-334 (2009).
• [12] O. Rehme, C. Emmelmann, J. Laser Micro Nanoeng. 4 (2), 128-134 (2009).
• [13] E. Louvis, P. Fox, C.J. Sutcliffe, J. Mater. Process. Technol. 211, 275-284 (2011).
• [14] C. Yan, L. Hao, A. Hussein, D. Raymont, Mater. Des. Process. Commun. e205, 3 (2021).
• [15] A. Zargarian, M. Esfahanian, J. Kadkhodapour, S. Ziaei-Rad, Mater. Sci. Eng. C 60, 339-347 (2016).
• [16] L. Yang, R. Mertens, M. Ferrucci, C. Yan, Y. Shi, S. Yang, Mater. Des. 162, 394-404 (2019).
• [17] C. Yan, L. Hao, A. Hussein, P. Young, D. Raymont, Mater. Des. 55, 533-541 (2014).
• [18] I. Maskery, N.T. Aboulkhair, A.O. Aremu, C.J. Tuck, I.A. Ashcroft, Addit. Manuf. 16, 24-29 (2017).
• [19] S.-Y. Park, K.-S. Kim, B. AlMangour, D. Grzesiak, ­K.-A. Lee, Mater. Des. 206, 109778 (2021).
• [20] O. Al-Ketan, R.K.A. Al-Rub, J. Mater. Res. 33 (3), 343-359 (2018).
• [21] A.S. Dalaq, D.W. Abueidda, R.K.A. Al-Rub, Compos. Part A-Appl. S. 84, 266-280 (2016).
• [22] A. Takaichi, Suyalatu, T. Nakamoto, N. Joko, N. Nomura, Y. Tsutsumi, S. Migita, H. Doi, S. Kurosu, A. Chiba, N. Wakabayashi, Y. Igarashi, T. Hanawa, J. Mech. Behav. Biomed. 21, 67-76 (2013).
• [23] K.-S. Kim, J.-W. Hwang, J. Alloys Compd. 834, 155055 (2020).
• [24] A. Chiba, K. Kumagai, N. Nomura, S. Miyakawa, Acta Mater. 55, 1309-1318 (2007).
• [25] M. Mori, K. Yamanaka, A. Chiba, J. Mech. Behav. Biomed. Mater. 55, 201-214 (2016).
• [26] S.M. Ahmadi, R. Hedayati, Y. Li, K. Lietaert, N. Tümer, A. Fatemi, C.D. Rans, B. Pouran, H. Weinans, A.A. Zadpoor, Acta Biomater. 65, 292-304 (2018).
• [27] C. Bonatti, D. Mohr, J. Mech. Phys. Solids 122, 1-26 (2019).
• [28] L.J. Gibson, M.F. Ashby, Cellular solid: structure and properties, 2nd ed., Cambridge University, Cambridge (1997).

Uwagi

1. This research was supported by Korea Institute for Advancement of Technology (KIAT) grant funded by the Korea Government (MOTIE) (P0002007, The Competency Development Program for Industrial Specialist).

2. Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023).