Tytuł artykułu
Wybrane pełne teksty z tego czasopisma
Identyfikatory
Warianty tytułu
Języki publikacji
Abstrakty
Until recently, the strengthening efficiency of carbonaceous reinforcements in aluminum-based matrix nanocomposites (AlMNCs) was lower than expected. The intrinsic characteristics of matrix and carbonaceous reinforcements and fabrication technique, which affected the microstructural characterization, played main roles in determining the performance of Cs/AlMNCs. In this study a novel strategy was developed via flake powder metallurgy followed by slurry blending combined with rheocasting and hot-extrusion processing to prepare hybrid AA7075-matrix composite reinforced with CNTs + GNPs. No Al4C3 phase was detected in Raman spectrums, while uniform dispersion of carbonaceous hybrid reinforcements with minimal structural damage was observed. There were ~ 9% and 39% decrease in the average grain size of the as-casted and extruded CNTs + GNPs/AA7075 composites, respectively, compared to AA7075 alloy. In the extruded CNTs + GNPs/AA7075 composite, plate precipitates were predominant and some lath-like dynamic precipitates were observed at the GNPs/AA7075 interfaces. The micro-hardness, tensile yield strength (TYS), ultimate tensile strength (UTS) and uniform elongation (UE) of the CNTs + GNPs/AA7075 composite were improved by ~ 17%, 51%, 7% and 20% compared to AA7075 alloy. An ultra-high yield strengthening efficiency of carbonaceous hybrid reinforcements in AA7075 alloy up to 3950 was obtained, where load bearing was the main strengthening mechanism and carbonaceous reinforcements illustrated bridging and pulling-out in the fracture surfaces of composite.
Czasopismo
Rocznik
Tom
Strony
263--286
Opis fizyczny
Bibliogr. 55 poz., rys., wykr.
Twórcy
autor
- Department of Engineering Sciences, Hakim Sabzevari University, Sabzevar, Iran
autor
- Department of Engineering Sciences, Hakim Sabzevari University, Sabzevar, Iran
autor
- Materials and Metallurgical Engineering Department, Faculty of Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
Bibliografia
- [1] Singh KL, Bhadauria A, Laha T. Comparing the strengthening efficiency of multiwalled carbon nanotubes and graphene nanoplatelets in aluminum matrix. Powder Technol. 2019;356:1059–76.
- [2] Imran M, Khan ARA. Characterization of Al-7075 metal matrix composites: a review. J Mater Res Technol. 2019;8:3347–56.
- [3] Singh J, Chauhan A. Characterization of hybrid aluminum matrix composites for advanced applications-a review. J Mater Res Technol. 2016;5:159–69.
- [4] Li J, Zhang X, Geng L. Effect of heat treatment on interfacial bonding and strengthening efficiency of graphene in GNP/Al composites. Compos Part A Appl Sci Manuf. 2019;121:487–98.
- [5] Parizi Torabi M, Ezatpour HR, Ebrahimi GR. High mechanical efficiency, microstructure evaluation and texture of rheo-casted and extruded AZ80-Ca alloy reinforced with processed Al2O3/GNPs hybrid reinforcement. Mater Chem Phys. 2018;218:246–55.
- [6] Zhou W, Mikulova P, Fan Y, Kikuchi K, Nomura N, Kawasaki A. Interfacial reaction induced efficient load transfer in few-layer graphene reinforced Al matrix composites for high-performance conductor. Compos Part B Eng. 2019;167:93–9.
- [7] Parizi Torabi M, Ebrahimi GR, Ezatpour HR, Paidar M. The structure effect of carbonaceous reinforcement on the microstructural characterization and mechanical behavior of AZ80 magnesium alloy. J Alloys Compd. 2019;809:151682.
- [8] Li Z, Fan G, Guo Q, Li Z, Su Y, Zhang D. Synergistic strengthening effect of graphene-carbon nanotube hybrid structure in aluminum matrix composites. Carbon. 2015;95:419–27.
- [9] Zeng X, Yu J, Fu D, Zhang H, Teng J. Wear characteristics of hybrid aluminum-matrix composites reinforced with well-dispersed reduced graphene oxide nanosheets and silicon carbide particulates. Vacuum. 2018;155:364–75.
- [10] Saravanan C, Dinesh S, Sakthivel P, Vijayan V, Suresh Kumar B. Assessment of mechanical properties of Silicon carbide and graphene reinforced aluminium composite. Mater Today Proc. 2020;21:744–7.
- [11] Kim WJ, Yu YJ. The effect of the addition of multiwalled carbon nanotubes on the uniform distribution of TiC nanoparticles in aluminum nanocomposites. Scr Mater. 2014;72–73:25–8.
- [12] Guo B, Cen X, Zhang X, Wang X, Song M, Ni S. Ameliorated mechanical and thermal properties of SiC reinforced Al matrix composites through hybridizing carbon nanotubes. Mater Charact. 2018;136:272–80.
- [13] Ghasali E, Sangpour P, Jam A, Rajaei H, Shirvanimoghaddam K, Ebadzadeh T. Microwave and spark plasma sintering of carbon nanotube and graphene reinforced aluminum matrix composite. Arch Civil Mech Eng. 2018;18:1042–54.
- [14] Xu R, Tan Z, Xiong D, Fan G, Guo Q, Zhang J, Su Y, Li Z, Zhang D. Balanced strength and ductility in CNT/Al composites achieved by flake powder metallurgy via shift-speed ball milling. Compos Part A Appl Sci Manuf. 2017;96:57–66.
- [15] Fan G, Jiang Y, Tan Z, Guo Q, Xiong D-b, Su Y, Lin R, Hu L, Li Z, Zhang D. Enhanced interfacial bonding and mechanical properties in CNT/Al composites fabricated by flake powder metallurgy. Carbon. 2018;130:333–9.
- [16] Yu Z, Yang W, Zhou C, Zhang N, Chao Z, Cao Y, Sun Y, Shao P, Wu G. Effect of ball milling time on graphene nanosheets reinforced Al6063 composite fabricated by pressure infiltration method. Carbon. 2019;141:25–39.
- [17] Guo B, Chen B, Zhang X, Cen X, Wang X, Song M, Ni S, Yi J, Shen T, Du Y. Exploring the size effects of Al4C3 on the mechanical properties and thermal behaviors of Al-based composites reinforced by SiC and carbon nanotubes. Carbon. 2018;135:224–35.
- [18] Yu Z, Tan Z, Xu R, Ji G, Fan G, Xiong DB, Guo Q, Li Z, Zhang D. Enhanced load transfer by designing mechanical interfacial bonding in carbon nanotube reinforced aluminum composites. Carbon. 2019;146:155–61.
- [19] Jiang L, Li Z, Fan G, Cao L, Zhang D. The use of flake powder metallurgy to produce carbon nanotube (CNT)/aluminum composites with a homogenous CNT distribution. Carbon. 2012;50:1993–8.
- [20] Jiang L, Fan G, Li Z, Kai X, Zhang D, Chen Z, Humphries S, Heness G, Yiu Yeung W. An approach to the uniform dispersion of a high-volume fraction of carbon nanotubes in aluminum powder. Carbon. 2011;49:1965–71.
- [21] Jiang L, Li Z, Fan G, Cao L, Zhang D. Strong and ductile carbon nanotube/aluminum bulk nanolaminated composites with two-dimensional alignment of carbon nanotubes. Scr Mater. 2012;66:331–4.
- [22] Sun W, Zhan K, Yang Z, Zhao R, Wang T, Zhao B, Ya Y, Yang J. Facile fabrication of GO/Al composites with improved dispersion of graphene and enhanced mechanical properties by Cu doping and powder metallurgy. J Alloys Compd. 2020;815:152465.
- [23] Alipour M, Eslami-Farsani R. Synthesis and characterization of graphene nanoplatelets reinforced AA7068 matrix nanocomposites produced by liquid metallurgy route. Mater Sci Eng A. 2017;706:71–82.
- [24] Yang W, Chen G, Qiao J, Liu S, Xiao R, Dong R, Hussain M, Wu G. Graphene nanoflakes reinforced Al–20Si matrix composites prepared by pressure infiltration method. Mater Sci Eng A. 2017;700:351–7.
- [25] Yang W, Zhao Q, Xin L, Qiao J, Zou J, Shao P, Yu Z, Zhang Q, Wu G. Microstructure and mechanical properties of graphene nanoplates reinforced pure Al matrix composites prepared by pressure infiltration method. J Alloys Compd. 2018;732:748–58.
- [26] Mirjavadi SS, Alipour M, Hamouda AMS, Kord S, Koppad PG, Abuzin YA, Keshavamurthy R. Effect of hot extrusion and T6 heat treatment on microstructure and mechanical properties of Al–10Zn-3.5 Mg–2.5 Cu nanocomposite reinforced with graphene nanoplatelets. J Manuf Proc. 2018;36:264–71.
- [27] Shao P, Yang W, Zhang Q, Meng Q, Tan X, Xiu Z, Qiao J, Yu Z, Wu G. Microstructure and tensile properties of 5083 Al matrix composites reinforced with graphene oxide and graphene nanoplates prepared by pressure infiltration method. Compos Part A Appl Sci Manuf. 2018;109:151–62.
- [28] Ramkumar KR, Sivasankaran S, Al-Mufadi AF, Siddharth S, Raghu R. Investigations on microstructure, mechanical, and tribological behaviour of AA 7075–x wt% TiC composites for aerospace applications. Arch Civil Mech Eng. 2019;19:428–38.
- [29] Jiang Y, Tan Z, Fan G, Wang L, Xiong DB, Guo Q, Su Y, Li Z, Zhang D. Reaction-free interface promoting strength-ductility balance in graphene nanosheet/Al composites. Carbon. 2020;158:449–55.
- [30] Li Z, Fan G, Tan Z, Guo Q, Xiong D, Su Y, Li Z, Zhang D. Uniform dispersion of graphene oxide in aluminum powder by direct electrostatic adsorption for fabrication of graphene/Al composites. Nanotechnology. 2014;25:325601.
- [31] Pelleg J, Ashkenazi D, Ganor M. The influence of a third element on the interface reactions in metal–matrix composites (MMC): Al–graphite system. Mater Sci Eng A. 2000;281:239–47.
- [32] Wang X, Jiang D, Wu G, Li B, Li P. Effect of Mg content on the mechanical properties and microstructure of Grf/Al composite. Mater Sci Eng A. 2008;497:31–6.
- [33] Yang W, Chen G, Qiao J, Liu S, Xiao R, Dong R. Graphene nanoflakes reinforced Al–20Si matrix composites prepared by pressure infiltration method. Mater Sci Eng A. 2017;700:351–7.
- [34] Mokdad F, Chen DL, Liu ZY, Xiao BL, Ni DR, Ma ZY. Deformation and strengthening mechanisms of a carbon nanotube reinforced aluminum composite. Carbon. 2016;104:64–77.
- [35] Engler O, Hirsch J, Lücke K. Texture development in Al-1.8 wt% Cu depending on the precipitation state-II. Recrystallization textures. Acta Metall Mater. 1995;43:121–38.
- [36] Wang SC, Starink MJ, Gao N, Xu C, Langdon TG. Grain structure and texture development during ECAP of two heat-treatable Al-based alloys. Rev Adv Mater Sci. 2005;10:249–55.
- [37] Wang XF, Guo MX, Cao LY, Wang F, Zhong JS, Zhuang LZ. Effect of rolling geometry on the mechanical properties, microstructure and recrystallization texture of AleMgeSi alloys. Int J Min Metall Mater. 2015;22:738–47.
- [38] Chen XH, Yan H. Solid–liquid interface dynamics during solidification of Al7075–Al2O3np based metal matrix composites. Mater Des. 2016;94:148–58.
- [39] Torabi Parizi M, Ebrahimi GR, Ezatpour HR. Effect of graphene nanoplatelets content on the microstructural and mechanical properties of AZ80 magnesium alloy. Mater Sci Eng A. 2019;742:373–89.
- [40] Wu LM, Seyring M, Rettenmayr M, Wang WH. Characterization of precipitate evolution in an artificially aged Al–Zn–Mg–Sc–Zr alloy. Mater Sci Eng A. 2010;527:1068–73.
- [41] Wu C, Ma K, Zhang D, Wu J, Xiong S, Luo G, Zhang J. Precipitation phenomena in Al–Zn–Mg alloy matrix composites reinforced with B4C particles. Sci Rep. 2017;7:1–11.
- [42] Hong SI, Gray GT. Microstructure and microchemistry of an Al–Zn–Mg–Cu alloy matrix-20 vol% SiC composite. Acta Metall Mater. 1992;40:3299–315.
- [43] Wu C, Shi R, Luo G, Zhang J, Shen Q, Gan Z, Liu J, Zhang L. Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite. J Alloys Compd. 2019;789:825–33.
- [44] Gjønnes J, Simensen CHRJ. An electron microscope investigation of the microstructure in an aluminium-zinc-magnesium alloy. Acta Metall. 1970;18:881–90.
- [45] Bailey JE, Hirsch PB. The recrystallization process in some polycrystalline metals. Proc R Soc Lond Ser A Math Phys Sci. 1962;267:11–30.
- [46] Mandal S, Jayalakshmi M, Bhaduri AK, Sarma VS. Effect of strain rate on the dynamic recrystallization behavior in a nitrogen enhanced 316L (N). Metall Mater Trans A. 2014;45:5645–56.
- [47] Ramezanzade S, Ebrahimi GR, Torabi Parizi M, Ezatpour HR. Microstructure and mechanical characterizations of graphene nanoplatelets-reinforced Mg–Sr–Ca alloy as a novel composite in structural and biomedical applications. J Compos Mater. 2020;54:711–28.
- [48] Taheri-Mandarjani M, Zarei-Hanzaki A, Abedi HR. Hot ductility behavior of an extruded 7075 aluminum alloy. Mater Sci Eng A. 2015;637:107–22.
- [49] Ramezanzade S, Ebrahimi GR, Parizi MT, Ezatpour HR. Synergetic effect of GNPs and MgOs on the mechanical properties of Mg–Sr–Ca alloy. Mater Sci Eng A. 2019;761:138025.
- [50] Jiang Y, Xu R, Tan Z, Ji G, Fan G, Li Z, Xiong DB, Guo Q, Li Z, Zhang D. Interface-induced strain hardening of graphene nanosheet/aluminum composites. Carbon. 2019;146:17–27.
- [51] Xu R, Fan G, Tan Z, Ji G, Chen C, Beausir B. Back stress in strain hardening of carbon nanotube/aluminum composites. Mater Res Let. 2017;6:113–20.
- [52] Shin SE, Choi HJ, Hwang JY, Bae DH. Strengthening behavior of carbon/metal nanocomposites. Sci Rep. 2015;5:16114.
- [53] Zhao Y, Song B, Pei J, Jia C, Li B, Linlin G. Effect of deformation speed on the microstructure and mechanical properties of AA6063 during continuous extrusion process. J Mater Proc Technol. 2013;213:1855–63.
- [54] Munitz A, Cotler C. Aging impact on mechanical properties and microstructure of Al-6063. J Mater Sci. 2000;35:2529–38.
- [55] Zare H, Jahedi M, Toroghinejad MR, Meratian M, Knezevic M. Compressive, shear, and fracture behavior of CNT reinforced Al matrix composites manufactured by severe plastic deformation. Mater Des. 2016;106:112–9.
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-2008a6a2-94af-4d3e-bd90-0f3ddd48ac86