Adhesive bond of carbon steel S235J0: effects of aluminium and polymer powder filled epoxy adhesives on mechanical properties

• Autorzy: Müller M. , Valášek P.

Identyfikatory

DOI

10.12913/22998624/64065

• Języki publikacji: EN

Abstrakty

EN

The paper deals with the testing of composite materials based on aluminium and polymer microparticles. The aim of the research was to determine an influence of a content of a microparticle filler on mechanical properties of the polymer particle composite and adhesive bonds (material structural carbon steel S235J0). A preparation of adhesive bonds and a process of testing of the adhesive bonds were in accordance with the standard CSN EN 1465. The adhesive bond strength was increased when adding the aluminium and polymer powder filler. The adhesive bond strength increase was the highest at the adhesive bond with the adhesive in the form of the composite (15 g of the filler : 100 g of the matrix). The adhesive bond strength increase was 14.3% (13.68 ± 0.43 MPa). Adhesive bonds evinced an adhesive type of a fracture surface. By adding the filler in a form of microparticles there was a change of the failure type on adhesive-cohesive and a cohesive type. Fracture surfaces and an adhesive bond cut was examined with SEM (scanning electron microscopy) using a microscope MIRA 3 TESCAN.

Słowa kluczowe

EN

adhesive bond strength; SEM; microparticles filler; tensile strength; elongation; structural two-component epoxy

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2016
• Tom: Vol. 10, nr 31
• Strony: 87--93
• Opis fizyczny: Bibliogr. 34 poz., fig.

Twórcy

autor

Müller M.

• Faculty of Engineering, Czech University of Life Science Prague, 165 21 Prague, Czech Republic

autor

Valášek P.

• Faculty of Engineering, Czech University of Life Science Prague, 165 21 Prague, Czech Republic

Bibliografia

• 1. Müller M., Herák D., Valášek, P.: Degradation limits of bonding technology depending on destinations Europe, Indonesia. Tehnicki Vjesnik-Technical Gazette, 20(4), 2013, 571-575.
• 2. Müller M., Chotěborský R., Valášek P., Hloch S.: Unusual possibility of wear resistance increase research in the sphere of soil cultivation. Tehnicki Vjesnik-Technical Gazette, 20(4), 2013, 641-646.
• 3. Müller M., Valášek P.: Degradation medium of agrokomplex - adhesive bonded joints interaction. Research in Agricultural Engineering, 58, 2012, 83-91.
• 4. Müller M.: Influence of cyclic degradation in saline solution on mechanical properties of adhesive bonds. Manufacturing Technology, 16(1), 2016, 204-209.
• 5. Borsellino C., Bell G., Di Ruisi V.F.: Adhesive joining of aluminium AA6082: The effects of resin and surface treatment. International Journal of Adhesion and Adhesives, 29, 2009, 36–44.
• 6. Müller M.: Research of liquid contaminants influence on adhesive bond strength applied in agricultural machine construction. Agronomy Research, 11(1), 2013, 147–154.
• 7. Rudawska A.: Influence of the thickness of joined elements on lap length of aluminium alloy sheet bonded joints. Advances in Science and Technology Research Journal, 9(27), 2015, 35-44.
• 8. Valášek P., Müller, M.: Abrasive wear in three-phase waste based polymeric particle composites. Tehnicki Vjesnik-Technical Gazette, 12(2), 2015, 257-262.
• 9. Valášek P., Müller M., Hloch S.: Recycling of corundum particles – two-body abrasive wear of polymeric composites based on waste. Tehnicki Vjesnik-Technical Gazette, 22(3), 2015, 567-572.
• 10. Rudawska A.: Pressure during curing and the strength of 2024, 2017A and 1050 aluminium alloy sheet adhesive joints. Advances in Science and Technology Research Journal, 9(26), 2015, 96-103.
• 11. Rudawska A., Czarnota M.: Selected aspects of epoxy adhesive compositions curing process. Journal Adhesion Science and Technology, 27(17), 2013, 1933-1950.
• 12. Rudawska A.: Surface free energy and geometric structures of the surfaces of selected epoxy composites. Polimery, 53, 2008, 452-456.
• 13. Ramazan K., Mehmet S., Bekir Y.: Influence of adhesive thickness and filler content on the mechanical performance of aluminium single-lap joints bonded with aluminium powder filled epoxy adhesive. Journal of Materials Processing Technology, 205, 2008, 183–189.
• 14. Rudawska A.: Surface Free Energy and 7075 Aluminium Bonded Joint Strength Following Degreasing Only and Without Any Prior Treatment. Journal Adhesion Science and Technology, 26, 2012, 1233-1247.
• 15. Rudawska A.: Selected aspects of the effect of mechanical treatment on surface roughness and adhesive joint strength of steel sheets. International Jurnal of Adhesion and Adhesives, 50, 2014, 235-243.
• 16. Cho J., Joshi M.S., Sun C.T.: Effect of inclusion size on mechanical properties of polymeric composites with micro and nano particles. Composites Science and Technology, 66, 2006, 1941–1952.
• 17. Shao-Yun Fu, Xi-Qiao Feng, Bernd Luke, Yiu- Wing Mai: Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate-polymer composites. Composites: Part B, 39, 2008, 933–961.
• 18. Müller M.: Polymer composites based on AL2O3 reinforcing particles. Engineering for Rural Development 26.05.2011, Jelgava. Jelgava: Latvia University of Agriculture, 2011, 423-427.
• 19. Müller M., Cidlina J., Dědičová K., Krofová K.: Mechanical properties of polymer composite based on aluminium microparticles. Manufacturing Technology, 15(4), 2015, 624–628.
• 20. Müller M.: Research of liquid contaminants influence on adhesive bond strength applied in agricultural machine construction. Agronomy Research, 11(1), 2013, 147–154.
• 21. Ruggiero A., Valášek P., Merola M.: Friction and wear behaviors of Al/Epoxy composites during reciprocating sliding tests. Manufacturing Technology, 15(4), 2015, 684–689.
• 22. Valášek P., Müller M.: Aplikace otěruvzdorných polymerích částicových kompozitů v oblasti konstrukce orebního tělesa. Listy Cukrovarnické a Řepařské, 130(9-10), 2014, 284-288.
• 23. Jäckel M., Scheibner W.: Boundary layer induced modification of thermal and mechanical properties of epoxy resin composites Boundary layer induced modification of thermal and mechanical properties of epoxy resin composites. Cryogenics, 31(4), 1991, 269–272.
• 24. Józwik J., Kuric I., Sága M., Lonkowic P.: Diagnostics of CNC machine tools in manufacturing process with laser interferometer technology. Manufacturing Technology, 14, 2014, 23-30.
• 25. Kováč I., Mikuš R., Žarnovský J., Drlička R., Žitňaský J., Výrostková A.: Creation of wear resistant boride layers on selected steel grades in electrical arc remelting process. Kovové Materially. 52, 2014, 387-397.
• 26. Novák M.: Surfaces with high precision of roughness after grinding. Manufacturing Technology, 12, 2012, 66–70.
• 27. Ruggiero A., D’Amato R., Gómez E., Merola M.: Experimental comparison on tribological pairs UHMWPE/TIAL6V4 alloy, UHMWPE/AISI316L austenitic stainless and UHMWPE/AL2O3 ceramic, under dry and lubricated conditions. Tribology International, 96, 2016, 349–360.
• 28. Ruggiero A., Merola M., Carlone P., Archodoulaki V.: Tribo-mechanical characterization of reinforced epoxy resin under dry and lubricated contact conditions. Compos Part B: Eng., 79, 2015, 595–603.
• 29. Ruggiero A., Hloch S., Kozak D., Valasek P.: Analytical fluid film force calculation in the case of short bearing with a fully developed turbulent flow. In. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 230(4), 2016, 395-401.
• 30. Sadílek M., Kratochvíl J., Petrů J, Cep R., Zlámal T., Stančeková D.: Cutting tool wear monitoring with the use of impedance layers. Tehnicki Vjesnik, 21(3), 2014, 639–644.
• 31. Náprstková N., Cais J., Stančeková D.: Influence of AlSi7Mg0.3 alloy modification by Sb on the tool wear. In. Manufacturing Technology, 1, 2014, 75–79.
• 32. Stančekova D., Kurnava T., Sajgalik M., Náprstková N., Struharnansky J., Ščotka P.: Identification of machinability of ceramic materials by turning. Manufacturing Technology, 1, 2014, 91-97.
• 33. Mrazova M., Stancekova D., Semcer J.: Comparasion of machinability of biocompatible materials used in medicine for dental implants. In: DAAAM and Proceedings of the International DAAAM Symposium, 2011, 1115-1116.
• 34. Farrah N.A., Mariatti J., Samayamuthirian P., Khairun A.M.: Effect of particle shape of silica minerál on the properties of epoxy composites. Composites Science and Technology, 68, 2008, 346-353.