The influence of hot dip galvanizing process on trip steel wire structure and properties

• Autorzy: Wiewiórowska S. , Muskalski Z. , Michalczyk J.

Identyfikatory

DOI

10.24425/amm.2019.126228

• Języki publikacji: EN

Abstrakty

EN

Many wire products (e.g. nets) are made from galvanized material. The hot dip galvanizing process gives the possibility of applying in a respectively thick coat of zinc (also depending on the time of staying wires in the bath) which provides the protection of the product against corrosion. In the available literature there were no research concerned with the influence of hot dip galvanizing process on the mechanical properties TRIP structure steel wires. Therefore, an experiment was carried out in laboratory conditions allowing the determination of the influence of hot dip galvanizing process parameters on the mechanical properties (tensile strength UST and yield strength YS) of TRIP steel wires as well as on the amount of retained austenite in their structure. It has been stated that the hot galvanizing process of TRIP steel wires influences, proportionally to the time of staying wires in zinc bath, on their plastic properties (the increase in yield strength YS) as well as the decrease in the amount of retained austenite in their structure. Such a phenomenon can be caused by stresses responsible for rapid heating of the wire put in the zinc bath in temperature of 450°C and by the strengthening of the materials resulting from the transformation of retained austenite.

Słowa kluczowe

EN

TRIP steel; galvanizing process; wires; drawing process

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2019
• Tom: Vol. 64, iss. 1
• Strony: 129--132
• Opis fizyczny: Bibliogr. 8 poz., fot., rys., tab.

Twórcy

autor

Wiewiórowska S.

• Czestochowa University of Technology, Faculty of Production Engineering and Materials Technology, 19 Armii Krajowej Av., 42-200 Częstochowa, Poland

autor

Muskalski Z.

• Czestochowa University of Technology, Faculty of Production Engineering and Materials Technology, 19 Armii Krajowej Av., 42-200 Częstochowa, Poland

autor

Michalczyk J.

• Czestochowa University of Technology, Faculty of Production Engineering and Materials Technology, 19 Armii Krajowej Av., 42-200 Częstochowa, Poland

Bibliografia

• [1] G. Michta, J. Pietrzyk, W. Osuch, The stability of reatined austenite occurred in low temperatures for low carbon steel with copper with TRIP effect, (in Polish), Inżynieria Materiałowa 6, 339-342 (2003).
• [2] A. Perlade, O. Bouaziz, Q. Furnemont, A physically based model for TRIP-aided carbon steel behaviour, Materials Science and Engineering A356, 145-152 (2003).
• [3] S. Wiewiórowska, Z. Muskalski, M. Siemiński, The analysis of “hot” drawing process of TRIP steel wires at different initial temperatures. Archives of Metallurgy and Materials 61, 1991-1994 (2016).
• [4] J. Mahieu, B.C. De Cooman, J. Maki, S. Claessens, Hot-dip galvanizing of Al alloyed TRIP steels, Iron and Steelmaker 29 (6), 29-34 (2002).
• [5] C. G. Lee, S. J. Kim, T. H. Lee, C. S. Oh, Effects of Tramp Elements on Formability of Low-carbon TRIP aided Multiphase Cold-rolled Steel Sheets, ISIJ Int. 44, (4), 737-743 (2004).
• [6] B. Mintz, Hot dip galvanising of transformation induced plasticity and other intercritically annealed steels, International Materials Reviews 46, (4), 169-197 (2001).
• [7] E. Girault, Banitic transformation in TRIP-assisted steels and its influence on mechanical properties, KULeuven MTM, 1999 (doctoral thesis).
• [8] S. Wiewiórowska, A theoretical and experimental analysis of the processes of drawing new-generation TRIP steel wires, (in Polish). Series Monografie no. 18, Częstochowa 2011.

Uwagi

EN

1. This work was realized under support of The Polish Ministry of Science and Higher Education, project no. BS-201-3011/2013.

PL

2. Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2019).