Influence of the Sr and Mg Alloying Additions on the Bonding Between Matrix and Reinforcing Particles in the AlSi7Mg/SiC-Cg Hybrid Composite

• Autorzy: Dolata A. J. , Dyzia M. , Boczkal S.

Identyfikatory

DOI

10.1515/amm-2016-0111

• Języki publikacji: EN

Abstrakty

EN

The aim of the work was to perform adequate selection of the phase composition of the composite designated for permanent - mould casting air compressor pistons. The hybrid composites based on AlSi7Mg matrix alloy reinforced with mixture of silicon carbide (SiC) and glassy carbon (Cg) particles were fabricated by the stir casting method. It has been shown that the proper selection of chemical composition of matrix alloy and its modification by used magnesium and strontium additions gives possibility to obtain both the advantageous casting properties of composite suspensions as well as good bonding between particles reinforcements and matrix.

Słowa kluczowe

EN

hybrid aluminium composites; Mg and Sr modification; solidification; structure; permanent mould casting

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2016
• Tom: Vol. 61, iss. 2A
• Strony: 651--656
• Opis fizyczny: Bibliogr. 39 poz., rys.

Twórcy

autor

Dolata A. J.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 8 Krasinskiego Str., 40-019 Katowice, Poland

autor

Dyzia M.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 8 Krasinskiego Str., 40-019 Katowice, Poland

autor

Boczkal S.

• Institute of Non-Ferrous Metals, Light Metals Division, 19. Piłsudskiego Str., 32-050 Skawina, Poland

Bibliografia

• [1] S. V. Prasad, R. Asthana, Tribol. Lett. 17, (3), 445-453 (2004).
• [2] M. Dyzia, Solid State Phenomena. 176, 49-54 (2011).
• [3] X. X. Zhang, B. L. Xiao, H. Andrä, Z. Y. Ma, Comp. Struct. 113, 459-468 (2014).
• [4] M. Kok, J. Mater. Process. Tech. 161, 381-87 (2005).
• [5] Y. Yalcin, H. Akbulut, Mater. Design. 27, 872-881 (2006).
• [6] M. Dyzia, A.J. Dolata, J. Szymczal, Mater. Today: Proc. 3, (2), 245-248 (2016).
• [7] DOI: 10.1016/j.matpr.2016.01.065
• [8] A. Manna, B. Bhattacharayya, J. Mater. Process. Tech. 140, (1-3), 711-716 (2003).
• [9] M. Ramulu, G. Paul, J. Patel, Comp. Struct. 54, 79-86 (2001).
• [10] J. Wieczorek, M. Dyzia, A. J. Dolata, Solid State Phenomena. 191, 75-80 (2012).
• [11] S. Suresha, B. K. Sridhara, Mater. Design. 34, 576-583 (2012).
• [12] A.R. Riahi, A. T. Alpas, Wear. 251, 1396-407 (2001).
• [13] S. Suresha, B. K. Sridhara, Mater. Design. 31, 1804-1812 (2010).
• [14] A. J. Dolata, Solid State Phenomena. 211, 47-52 (2014).
• [15] A. J. Dolata, M. Dyzia, IOP Conf. Ser.: Mater. Sci. Eng. 35, DOI. 10.1088/1757-899X/35/1/012020 (2012).
• [16] A. J. Dolata, M. Dyzia, Arch. Foundry Eng. 14, (1), 135-38 (2014).
• [17] A. Dolata-Grosz, Solid State Phenomena. 176, 55-62 (2011).
• [18] D. Rudnik, J. Sobczak, A. Wojciechowski, K. Pietrzak, KONES. 10, (3-4), 1-11 (2003).
• [19] D. S. Han, H. Jones, H. V. Atkinson, J. Mater. Sci. 28, 2654-2658 (1993).
• [20] J. Hashim, L. Looney, M. S. J. Hashmi, J. Mater. Process. Tech. 119, (1-3), 324-328 (2001).
• [21] K. Landry, S. Kalogeropoulou, N. Eustathopoulos, Mater. Sci. Eng. 254A, (1-2), 99-111 (1998).
• [22] B. Stunová, Acta Polytechnica, 52, (4), 26-32 (2012).
• [23] R. S. Rana, R. Purohit, S. Das, IJSRP 2, (6), 1-7 (2012).
• [24] F. H. Samuel, P. Ouellet, A. M. Samuel, H. W. Doty, Metall. Mater. Trans. 29A, 2871-2888 (1998).
• [25] A. Razaghia, M. Emamy, A. A. Najimi, S. H. S. Ebrahimi, Mater. Charact. 60, (11), 1361-1369 (2009).
• [26] B. C. Pai, G. Ramani, R. M. Pillai, K. G. Satyanarayana, J. Mater. Sci. 30, 1903-1911 (1995).
• [27] Z. Liu, G. Zu, H. Luo, Y. Liu, G. Yao, J. Mater. Sci. Technol. 26, (3), 244-250 (2010).
• [28] M. Dyzia, A. J. Dolata, J. Sleziona, Steel Res. Int. 83, (1), 981-987 (2012).
• [29] J. Sleziona, M. Dyzia, A. Dolata-Grosz, J. Wieczorek, PL Patent No. 391006-A1, Polish Patent Office, 2011.
• [30] E. Tillová, M. Chalupová, L. Hurtalová, Evolution of phases in a recycled Al-Si cast alloy during solution treatment, in: Scanning Electron Microscopy, Dr. V. Kazmiruk (Ed.), ISBN: 978-953-51-0092-8, InTech (2012), DOI: 10.5772/34542.
• [31] P. K. Rohatgi, S. Ray, R. Asthana, C. S. Narendranath, J. Mater. Sci. Eng. 162A, 163-174 (1993).
• [32] D. M. Stefanescu, B. K. Dhindaw, S. A. Kacar and A. Moitra, Metal. Trans. 19A, 2847-55 (1998).
• [33] A. Zyska, J. Braszczyński, Z. Konopka, Kompozyty (COMPOSITES) 1, (1), 114-117 (2001), in polish.
• [34] N. Sobczak, J. Sobczak, S. Seal, J. Morgiel, Mater. Chem. Phys. 81, (2), 319-322 (2003).
• [35] K. M. Shorowordi, T. Laoui, A.S.M.A. Haseeb, J.P. Celis, L. Froyen, J. Mater. Process. Tech. 142, 738-743 (2003).
• [36] D. J. Lloyd, I. Jin, Metall. Trans. 19A, 3107-3109 (1988).
• [37] L. Salvo, G.L. Esperance, M. Suery, J.G. Legoux, Mater. Sci. Eng. A177, 173-183 (1994).
• [38] A. C. Ferro, B. Derby, Acta Metall. Mater. 43, (8), 3061-3073 (1995).
• [39] M. I. Pech-Canul, R. N. Katz, M. M. Makhlouf, S. Pickard, J. Mater. Sci. 35, 2167-2173 (2000).