Effect of abrasive waterjet peening surface treatment of steel plates on the strength of single–lap adhesive joints

• Autorzy: Anasiewicz K. , Kuczmaszewski J.

Identyfikatory

DOI

10.12913/22998624/76480

• Języki publikacji: EN

Abstrakty

EN

The paper presents the results of a comparative study of shear strength of single–lap adhesive joints, depending on the method of surface preparation of steel plates with increased corrosion resistance. The method of preparing adherend surfaces is often one of the most important factors determining the strength of adhesive joints. Appropriate geometric surface development and cleaning of the surface enhances adhesion forces between adherend material and adhesive. One of the methods of shaping engineering materials is waterjet cutting, which in the AWJP – abrasive waterjet peening variant, serves to shape flat surfaces of the material by changing the roughness and introducing stresses into the surface layer. These changes are valuable when preparing adhesive joints. In the study, surface roughness parameters obtained with AWJP treatment, were analyzed in direct relation to the strength of the adhesive joint. As a consequence of the experimental results analysis, the increase in the strength of the adhesive joints was observed in a certain range of parameters used for AWJP treatment. A decrease in shear strength of adhesive joint with the most modified topography of overlap surface was observed.

Słowa kluczowe

EN

abrasive waterjet peening; AWJP; adhesive bonding; lap joints

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2017
• Tom: Vol. 11, no 3
• Strony: 270--276
• Opis fizyczny: Bibliogr. 9 poz., fig., tab.

Twórcy

autor

Anasiewicz K.

• Department of Production Engineering, Faculty of Mechanical Engineering, Lublin University of Technology, 36 Nadbystrzycka St., 20-618 Lublin, Poland

autor

Kuczmaszewski J.

• Department of Production Engineering, Faculty of Mechanical Engineering, Lublin University of Technology, 36 Nadbystrzycka St., 20-618 Lublin, Poland

Bibliografia

• 1.Arola D. D., McCain M. L. Abrasive Waterjet Peening: A New Method of Surface Preparation for Metal Orthopedic Implants. John Wiley & Sons, Inc. J Biomed Mater Res (Appl Biomater), 53, 536-546.
• 2.Bławucki S., Zaleski K. Nagniatanie dynamiczne kompozytów o osnowie metalowej. Mechanik, 3, 2015, 163-167.
• 3.Budhe S., Ghumatkar A., Birajdar N., Banea M. D. Effect of surface roughness using different adherend materials on the adhesive bond strength. Applied Adhesion Science, 2015.
• 4.Fernando D., Teng J. G., Yu T., Zhao X. L., Preparation and Characterization of Steel Surfaces for Adhesive Bonding. Journal of Composites for Construction, 6(17), 2013, 1-10
• 5.Grzesik W. Wpływ topografii powierzchni na właściwości eksploatacyjne części maszyn. Mechanik, 8-9, 2015, 587-593.
• 6.Kuczmaszewski J. Podstawy konstrukcyjne i technologiczne oceny wytrzymałości adhezyjnych połączeń metali. Wydawnictwa Uczelniane Politechniki Lubelskiej, 1995.
• 7.Müller M. Influence of surface integrity on bonding process. Research in Agricultural Engineering, 4(57), 2011, 153–162.
• 8.Rudawska A. Wpływ sposobu przygotowania powierzchni na wytrzymałość połączeń klejowych blach ze stali odpornej na korozję. Technologia i Automatyzacja Montażu 3, 2010, 36-39.
• 9.Sreekesh. K, Govindan P. A review on abrasive water jet cutting. International Journal of Recent Advances in Mechanical Engineering, 3(3), 2014, 153-158.

Uwagi

Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę (zadania 2017)