Influence of L-PBF additive manufacturing parameters on the residual stresses and thermal distortions in AISI 316L stainless steel parts

• Autorzy: Santos O. , Batalha G.F. , Farias V. , Seriacop V. , Bordinassi E.C. , Adamiak M.

Identyfikatory

DOI

10.5604/01.3001.0054.7283

• Języki publikacji: EN

Abstrakty

EN

Purpose: The work aimed to numerically model through the Finite Element Method (FEM) the distribution of residual stresses and thermal distortions in parts generated by Laser Powder Bed Fusion (L-PBF) in stainless steel AISI 316L and validate the results obtained through experimental measurements on previously manufactured parts. Design/methodology/approach: The design methodology followed a numerical approach through the Finite Element Method (FEM), the distribution of residual stresses and thermal distortions in parts generated by Selective Laser Powder Bed Fusion (L-PBF) in stainless steel AISI 316L and the FEM approach was validated trough the results obtained through experimental measurements on previously manufactured parts. The influence on three levels was verified through complete factorial planning of some manufacturing parameters, such as laser power, speed, and distance between scans (hatch), on the stress and distortion results of the samples and also on the samples simulated by FEM. Findings: When results were compared about the average diameters, a relative error of less than 2.5% was observed. The average diameter was influenced by power and speed. Increasing power decreased the average diameter of the samples, while increasing speed and hatch increased the average diameter. When results are compared to measure the residual stresses, it is observed that the relative error was less than 1%. Power, speed, and the hatch itself influenced the residual stress. Increasing power increases residual stress while increasing speed and hatch decreases residual stress. The cooling rate and the transient thermal history are the control factors that influence the residual stresses and are directly related to the process parameters. The computational modelling followed by measurements and calibrations carried out in the experimental stages proved to be efficient and enabled the reproduction of thermal distortion and residual stresses with statistical confidence. prediction of thermal distortions and residual stresses using the machine learning approach. Future research will study heating the building platform, which should also impact residual stresses. Practical implications: Based on the results obtained in this research, it will be possible to select better additive manufacturing parameters for manufacturing 316L stainless steel parts. The parameters evaluated in the work were laser power, scanning speed, and hatch. Originality/value: The innovation of the work lies in the robust simulation of the thermo-elastic behaviour of samples subjected to the additive manufacturing process, where it was possible to accurately relate the thermal distortions and residual stresses that appeared in the samples printed with the parts modelled by the FEM. The numerical-experimental validation makes it possible to extrapolate the studies to several other manufacturing parameters using only computational simulation and work with a more significant amount of data for a prediction study.

Słowa kluczowe

EN

additive manufacturing; L-PBF; stainless steel; 316L; numerical simulation; thermal distortions; residual stresses

PL

produkcja addytywna; L-PBF; stal nierdzewna; 316L; symulacja numeryczna; odkształcenia termiczne; naprężenia szczątkowe

• Wydawca: International OCSCO World Press
• Czasopismo: Archives of Materials Science and Engineering
• Rocznik: 2024
• Tom: Vol. 127, nr 1
• Strony: 12--22
• Opis fizyczny: Bibliogr. 58 poz.

Twórcy

autor

Santos O.

• Department of Mechatronics and Mechanical System Engineering, Polytechnic School, University of São Paulo, Brazil

autor

Batalha G.F.

• Department of Mechatronics and Mechanical System Engineering, Polytechnic School, University of São Paulo, Brazil

• https://orcid.org/0000-0001-8625-8499

autor

Farias V.

• Department of Mechanical Engineering, University Center of Maua Institute of Technology, São Caetano do Sul, Sao Paulo, Brazil

autor

Seriacop V.

• Department of Mechanical Engineering, University Center of Maua Institute of Technology, São Caetano do Sul, Sao Paulo, Brazil

autor

Bordinassi E.C.

• Materials Research Laboratory, Faculty Mechanical Engineering, Silesian University of Technology, ul. Konarskiego 18a, 44-100 Gliwice, Poland

autor

Adamiak M.

• Materials Research Laboratory, Faculty Mechanical Engineering, Silesian University of Technology, ul. Konarskiego 18a, 44-100 Gliwice, Poland

Bibliografia

• [1] Z. Jin, Z. Zhang, K. Demir, G.X. Gu, Machine Learning for Advanced Additive Manufacturing, Matter 3/5 (2020) 1541-1556. DOI: https://doi.org/10.1016/j.matt.2020.08.023
• [2] G. Prashar, H. Vasudev, D. Bhuddhi, Additive manufacturing: expanding 3D printing horizon in industry 4.0, International Journal on Interactive Design and Manufacturing 17 (2023) 2221-2235. DOI: https://doi.org/10.1007/s12008-022-00956-4
• [3] H.B. Mamo, M. Adamiak, A. Kunwar, 3D printed biomedical devices and their applications: A review on state-of-the-art technologies, existing challenges, and future perspectives, Journal of the Mechanical Behavior of Biomedical Materials 143 (2023) 105930. DOI: https://doi.org/10.1016/j.jmbbm.2023.105930
• [4] M. Khorasani, J. Loy, A.H. Ghasemi, E. Sharabian, M. Leary, H. Mirafzal, P. Cochrane, B. Rolfe, I. Gibson, A review of Industry 4.0 and additive manufacturing synergy, Rapid Prototyping Journal 28/8 (2022) 1462- 1475. DOI: https://doi.org/10.1108/RPJ-08-2021-0194
• [5] U.M. Dilberoglu, B. Gharehpapagh, U. Yaman, M. Dolen, The Role of Additive Manufacturing in the Era of Industry 4.0, Procedia Manufacturing 11 (2017) 545- 554. DOI: https://doi.org/10.1016/j.promfg.2017.07.148
• [6] P. Baras, J. Sawicki, Numerical analysis of mechanical properties of 3D printed aluminium components with variable core infill values, Journal of Achievements in Materials and Manufacturing Engineering 103/1 (2020) 16-24. DOI: https://doi.org/10.5604/01.3001.0014.6912
• [7] M. Deroszewska, R. Saraczyn, A. Cisowski, T. Kowaluk, T. Borowski, J. Petru, D. Myszka, Investigation of the impact of porosity of elements made using DMLS 3D printing technology and various printing angles on the mechanical properties and microstructure of 17-4 PH stainless steel, Journal of Achievements in Materials and Manufacturing Engineering 121/2 (2023) 289-305. DOI: https://doi.org/10.5604/01.3001.0054.3050
• [8] E. Brancewicz-Steinmetz, J. Sawicki, Post-processing in multi-material 3D printing, Journal of Achievements in Materials and Manufacturing Engineering 117/1 (2023) 5-14. DOI: https://doi.org/10.5604/01.3001.0053.5953
• [9] M. Król, L.A. Dobrzański, Ł. Reimann, I. Czaja, Surface quality in selective laser melting of metal powders, Archives of Materials Science and Engineering 60/2 (2013) 87-92.
• [10] M. Król, T. Tański, Surface quality research for selective laser melting of Ti-6AL-4V alloy, Archives of Metallurgy and Materials 61/3 (2016) 1291-1296. DOI: https://doi.org/10.1515/amm-2016-0213
• [11] J. Hajnys, M. Pagáč, J. Měsíček, J. Petru, M. Król, Influence of Scanning Strategy Parameters on Residual Stress in the SLM Process According to the Bridge Curvature Method for AISI 316L Stainless Steel, Materials 13/7 (2020) 1659. DOI: https://doi.org/10.3390/ma13071659
• [12] E.C. Bordinassi, V. Seriacopi, M.O. dos Santos, N.W. Paschoalinoto, A. de Farias, Effect of cryogenic cooling on residual stresses and surface finish of 316L during hybrid manufacturing, The International Journal of Advanced Manufacturing Technology 129 (2023) 1489-1502. DOI: https://doi.org/10.1007/s00170-023- 12380-3
• [13] A.S. Wu, D.W. Bown, M. Kumar, G.F. Gallegos, W.E. King, An Experimental Investigation into Additive Manufacturing-Induced Residual Stresses in 316L Stainless Steel, Metallurgical and Materials Transactions A 45 (2014) 6260-6270. DOI: https://doi.org/10.1007/s11661-014-2549-x
• [14] S. Waqar, K. Guo, J. Sun, FEM analysis of thermal and residual stress profile in selective laser melting of 316L stainless steel, Journal of Manufacturing Processes 66 (2021) 81-100. DOI: https://doi.org/10.1016/j.jmapro.2021.03.040
• [15] C. Casavola, S.L. Campanelli, C. Pappalettere, Experimental analysis of residual stresses in the Selective Laser Melting process, Proceedings of the XIth International Congress and Exposition, Orlando, USA, 2008.
• [16] J.H. Yu, Q.Y. Jin, K. Ha, W. Lee, Influence of Several Heat Treatments on Residual Stress in Laser Powder Bed-Fused Maraging 18Ni-300 Steel, Applied Sciences 13/11 (2023) 6572. DOI: https://doi.org/10.3390/app13116572
• [17] E.C. Bordinassi, S.U. Mhurchadha, V. Seriacopi, S. Delijaicov, S.M.G. Lebrão, K. Thomas, G.F. Batalha, R. Raghavendra, Effect of hybrid manufacturing (AM-machining) on the residual stress and pitting corrosion resistance of 316L stainless steel, Journal of the Brazilian Society of Mechanical Sciences and Engineering 44 (2022) 491. DOI: https://doi.org/10.1007/s40430-022-03813-3
• [18] C.E. Protasov, V.A. Safronov, D.V. Kotoban, A.V. Gusarov, Experimental study of residual stresses in metal parts obtained by selective laser melting, Physics Procedia 83 (2016) 825-832. DOI: https://doi.org/10.1016/j.phpro.2016.08.085
• [19] Q.-Y. Jin, D. Kang, K. Ha, J.H. Yu, W. Lee, Simulation of annealing process on AISI 316 L stainless steel fabricated via laser powder bed fusion using finite element method with creep, Additive Manufacturing 60/A (2022) 103255. DOI: https://doi.org/10.1016/j.addma.2022.103255
• [20] P. Bian, J. Shi, Y. Liu, Y. Xie, Influence of laser power and scanning strategy on residual stress distribution in additively manufactured 316L steel, Optics and Laser Technology 132 (2020) 106477. DOI: https://doi.org/10.1016/j.optlastec.2020.106477
• [21] C. Kushan, M. Poyraz, Ö. Uzunonat, Y.S Orak, Systematical review on the numerical simulations of laser-powered bed additive manufacturing, Sigma Journal of Engineering and Natural Science 36/4 (2018) 1197-1214.
• [22] L. Parry, I.A. Ashcroft, R.D. Wildman, Understanding the effect of laser scan strategy on residual stress in selective laser melting through thermo-mechanical simulation, Additive Manufacturing 12/A (2016) 1-15. DOI: https://doi.org/10.1016/j.addma.2016.05.014
• [23] Z. Yan, W. Liu, Z. Tang, X. Liu, N. Zhang, M. Li, H. Zhang, Review on thermal analysis in laser-based additive manufacturing, Optics and Laser Technology 106 (2018) 427-441. DOI: https://doi.org/10.1016/j.optlastec.2018.04.034
• [24] A. Olleak, Z. Xi, Efficient LPBF process simulation using finite element modeling with adaptive remeshing for distortions and residual stresses prediction, Manufacturing Letters 24 (2020) 140-144. DOI: https://doi.org/10.1016/j.mfglet.2020.05.002
• [25] T. Kim, K. Ha, Y.R. Cho, J.B. Jeon, W. Lee, Analysis of residual stress evolution during powder bed fusion process of AISI 316L stainless steel with experiment and numerical modeling, The International Journal of Advanced Manufacturing Technology 105 (2019) 309- 323. DOI: https://doi.org/10.1007/s00170-019-04204-0
• [26] M.A. Mahmood, A. Ur Rehman, T. Khan, T.D. Seers, F. Liou, M. Khraisheh, Defects quantification of additively manufactured AISI 316L stainless steel parts via non-destructive analyses: Experiments and semi- FEM-analytical-based modeling, Optics and Laser Technology 174 (2024) 110684. DOI: https://doi.org/10.1016/j.optlastec.2024.110684
• [27] P. Promoppatum, S.-C. Yao, Influence of scanning length and energy input on residual stress reduction in metal additive manufacturing: Numerical and experimental studies, Journal of Manufacturing Processes 49 (2020) 247-259. DOI: https://doi.org/10.1016/j.jmapro.2019.11.020
• [28] L. Cheng, A. To, Part-scale build orientation optimization for minimizing residual stress and support volume for metal additive manufacturing: Theory and experimental validation, Computer-Aided Design 113 (2019) 1-23. DOI: https://doi.org/10.1016/j.cad.2019.03.004
• [29] C. Li, J.F. Liu, X.Y. Fang, Y.B. Guo, Efficient predictive model of part distortion and residual stress in selective laser melting, Additive Manufacturing 17 (2017) 157-168. DOI: https://doi.org/10.1016/j.addma.2017.08.014
• [30] J.L. Bartlett, B.P. Croom, J.F. Burdick, D. Henkel, X. Li, Revealing mechanisms of residual stress development in additive manufacturing via digital image correlation, Additive Manufacturing 22 (2018) 1-12. DOI: https://doi.org/10.1016/j.addma.2018.04.025
• [31] R.J. Williams, F. Vecchiato, J. Kelleher, M.R. Wenman, P.A. Hooper, C.M. Davies, Effects of heat treatment on residual stresses in the laser powder bed fusion of 316L stainless steel: Finite element predictions and neutron diffraction measurements, Journal of Manufacturing Process 57 (2020) 641-653. DOI: https://doi.org/10.1016/j.jmapro.2020.07.023
• [32] K. Ha, T. Kim, G.Y. Baek, J.B. Jeon, D.-s. Shim, Y.H. Moon, W. Lee, Numerical study of the effect of progressive solidification on residual stress in single-bead-on plate additive manufacturing, Additive Manufacturing 34 (2020) 101245. DOI: https://doi.org/10.1016/j.addma.2020.101245
• [33] F.C. Pinto, L.S. Aota, I.R. Souza Filho, D. Raabe, H.R.Z. Sandim, Recrystallization in non-conventional microstructures of 316L stainless steel produced via laser powder-bed fusion: effect of particle coarsening kinetics, Journal of Materials Science 57/21 (2022) 9576-9598. DOI: https://doi.org/10.1007/s10853-021- 06859-1
• [34] E. Ramirez-Cedillo, M.J. Uddin, J.A. Sandoval-Robles, R.A. Mirshams, L. Ruiz-Huerta, C.A. Rodriguez, H.R. Siller, Process planning of L-PBF of AISI 316L for improving surface quality and relating part integrity with microstructural characteristics, Surface Coating Technology 396 (2020) 125956. DOI: https://doi.org/10.1016/j.surfcoat.2020.125956
• [35] J. Yu, D. Kim, K. Ha, J.B. Jeon, W. Lee, Strong feature size dependence of tensile properties and its microstructural origin in selectively laser melted 316L stainless steel, Materials Letters 275 (2020) 128161. DOI: https://doi.org/10.1016/j.matlet.2020.128161
• [36] J. Yu, D. Kim, K. Ha, J.B. Jeon, D.J. Kim, W. Lee, Size effect due to contour laser scanning in 316L stainless steel produced by laser powder bed fusion, Journal of Materials Research and Technology 15 (2021) 5554- 5568. DOI: https://doi.org/10.1016/j.jmrt.2021.11.034
• [37] M. Li, X. Zhang, W.-Y. Chen, T.S. Byun, Creep behavior of 316L stainless steel manufactured by laser powder bed fusion, Journal Nuclear Materials 548 (2021) 152847. DOI: https://doi.org/10.1016/j.jnucmat.2021.152847
• [38] L. Cui, S. Jiang, J. Xu, R.L. Peng, R.T. Mousavian, J. Moverare, Revealing relationships between microstructure and hardening nature of additively manufactured 316L stainless steel, Materials and Design 198 (2021) 109385. DOI: https://doi.org/10.1016/j.matdes.2020.109385
• [39] Q. Chen, X. Liang, D. Hayduke, J. Liu, L. Cheng, J. Oskin, R. Whitmore, A.C. To, An inherent strain based multiscale modeling framework for simulating part scale residual deformation for direct metal laser sintering, Additive Manufacturing 28 (2019) 406-418. DOI: https://doi.org/10.1016/j.addma.2019.05.021
• [40] X. Song, S. Feih, W. Zhai, C.-N. Sun, F. Li, R. Maiti, J. Wei, Y. Yang, V. Oancea, L.R. Brandt, A.M. Korsunsky, Advances in additive manufacturing process simulation: Residual stresses and distortion predictions in complex metallic components, Materials and Design 193 (2020) 108779. DOI: https://doi.org/10.1016/j.matdes.2020.108779
• [41] K. Carpenter, A. Tabei, On Residual Stress Development, Prevention, and Compensation in Metal Additive Manufacturing, Materials 13/2 (2020) 255. DOI: https://doi.org/10.3390/ma13020255
• [42] S. Dryepondt, P. Nandwana, P. Fernandez-Zelaia, F. List, Microstructure and high temperature tensile properties of 316L fabricated by laser powder-bed fusion, Additive Manufacturing 37 (2021) 101723. DOI: https://doi.org/10.1016/j.addma.2020.101723
• [43] P. Alvarez, J. Ecenarro, I. Setien, M. San Sebastian, A. Echeverria, L. Eciolaza, Computationally efficient distortion prediction in Powder Bed Fusion Additive Manufacturing. International Journal of Engineering Research and Science 2/10 (2016) 39-46.
• [44] B. Cheng, S. Shrestha, K. Chou, Stress and deformation evaluations of scanning strategy effect in selective laser melting, Additive Manufacturing 12/B (2016) 240-251. DOI: https://doi.org/10.1016/j.addma.2016.05.007
• [45] A.J Dunbar, E.R. Denlinger, J. Heigel, P. Michaleris, P. Guerrier, R. Martukanitz, T.W. Simpson, Development of experimental method in situ distortion and temperature measurements during the laser powder bed fusion additive manufacturing process, Additive Manufacturing 12/A (2016) 25-30. DOI: https://doi.org/10.1016/j.addma.2016.04.007
• [46] S.A. Khairallah, A. Anderson, Mesoscopic simulation model of selective laser melting of stainless-steel powder, Journal of Materials Processing Technology 214/11 (2014) 2627-2636. DOI: https://doi.org/10.1016/j.jmatprotec.2014.06.001
• [47] V.A. Safronov, R.S. Khmyrov, D.V. Kotoban, A.V. Gusarov, Distortions and residual stresses at layer-by-layer additive manufacturing by fusion, Journal of Manufacturing Science and Engineering 139/3 (2017) 031017. DOI: https://doi.org/10.1115/1.4034714
• [48] A.B. Spierings, N. Herres, G. Levy, Influence of the particle size distribution on surface quality and mechanical properties in additive manufactured stainless steel parts, Rapid Prototyping Journal 17/3 (2011) 195-202. DOI: https://doi.org/10.1108/13552541111124770
• [49] H. Roirand, A. Pugliara, B. Malard, A. Hor, N. Saintier, Multiscale study of additively manufactured 316L microstructure sensitivity to heat treatment over a wide temperature range, Materials Characterization 208 (2024) 113603. DOI: https://doi.org/10.1016/j.matchar.2023.113603
• [50] G. Mohr, S.J. Altenburg, K. Hilgenberg, Effects of inter layer time and build height on resulting properties of 316L stainless steel processed by laser powder bed fusion, Additive Manufacturing 32 (2020) 101080. DOI: https://doi.org/10.1016/j.addma.2020.101080
• ][51] H. Sohrabpoor, V. Salarvand, R. Lupoi, Q. Chu, W. Li, B. Aldwell, W. Stanley, S. O'Halloran, R. Raghavendra, C.-H. Choi, D. Brabazon, Microstructural and mechanical evaluation of post-processed SS 316L manufactured by laser-based powder bed fusion, Journal of Materials Research and Technology 12 (2021) 210-220. DOI: https://doi.org/10.1016/j.jmrt.2021.02.090
• [52] Z. Zheng, L. Peng, D. Wang, Defect Analysis of 316 L Stainless Steel Prepared by LPBF Additive Manufacturing Processes, Coatings 11/12 (2021) 1562. DOI: https://doi.org/10.3390/coatings11121562 [53] D. Cortis, D. Pilone, G. Broggiato, G.F. Campana, D. Tatananni, D. Orlandi, Setting of L-PBF parameters for obtaining high density and mechanical performance of AISI 316L and 16MnCr5 alloys with fine laser spot size, Progress in Additive Manufacturing (2023). DOI: https://doi.org/10.1007/s40964-023-00556-y
• [54] S. Cacace, L. Pagani, B.M. Colosimo, Q. Semeraro, The effect of energy density and porosity structure on tensile properties of 316L stainless steel produced by laser powder bed fusion, Progress in Additive Manufacturing 7 (2022) 1053-1070. DOI: https://doi.org/10.1007/s40964-022-00281-y
• [55] M.A. Chaudry, G. Mohr, K. Hilgenberg, Experimental and numerical comparison of heat accumulation during laser powder bed fusion of 316L stainless steel, Progress in Additive Manufacturing 7 (2022) 1071- 1083. DOI: https://doi.org/10.1007/s40964-022-00282-x
• [56] X. Yan, J. Pang, Y. Jing, Ultrasonic Measurement of Stress in SLM 316L Stainless Steel Forming Parts Manufactured Using Different Scanning Strategies, Materials 12/17 (2019) 2719. DOI: https://doi.org/10.3390/ma12172719
• [57] ASTM F3184-16, Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion, ASTM International, West Conshohocken, PA, 2024. DOI: https://doi.org/10.1520/F3184-16
• [58] Carpenter Technology Corporation, PowderRange 316L Datasheet. Available from: https://www.carpenteradditive.com/hubfs/Resources/ Data%20Sheets/PowderRange_316L_Datasheet.pdf (Access in: 15.06.2024)