PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Cyclic loading–unloading creep behavior of composite layered specimens

Wybrane pełne teksty z tego czasopisma
Identyfikatory
Warianty tytułu
Języki publikacji
EN
Abstrakty
EN
Soft and hard interbedded rocks show obvious time-dependent deformation after deep tunnel excavations, and it is therefore necessary to research the mechanical behavior of the layered rock. However, it is hard to obtain ideal transversely isotropic rocks in fields, so rock-like specimens were poured by using artificial materials. Cyclic loading–unloading creep experiments were performed on the artificial layered cemented specimens with various layer angles (0°, 30°, 60° and 90°) at a 20 MPa confinement. Time-independent deformations and time-dependent deformations of the rock-like specimens were distinguished to investigate the visco-elasto-plastic deformation characteristics. Instantaneous elastic strain and instantaneous plastic strain had linear correlations with stress ratio, whereas creep strain, including visco-elastic strain and visco-plastic strain, increased nonlinearly with an increasing stress ratio. The specimens with a small layer angle had more noticeable time-independent and time-dependent deformations and larger steady-state creep rates than those of the specimens with a large layer angle. Attenuation creep and secondary creep could be observed at relative low stress levels, whereas accelerating creep until failure occurred at the creep failure stress level. The time for creep failure can be predicated according to the axial steady-state creep rate or volumetric creep curve. Damage in the rock-like specimens showed linear correlation with the stress ratio. Dip angle has a significant effect on the creep failure mode under cyclic loading–unloading conditions.
Czasopismo
Rocznik
Strony
449--464
Opis fizyczny
Bibliogr. 55 poz.
Twórcy
autor
  • State Key Laboratory for Geomechanics and Deep Underground Engineering, School of Mechanics and Civil Engineering, China University of Mining and Technology, Xuzhou 221116, People’s Republic of China
  • State Key Laboratory for Geomechanics and Deep Underground Engineering, School of Mechanics and Civil Engineering, China University of Mining and Technology, Xuzhou 221116, People’s Republic of China
autor
  • China Construction Third Engineering Design Bureau Co., Ltd, Wuhan 430064, Hubei, People’s Republic of China
  • State Key Laboratory of Geohazard Prevention and Geoenvironment Protection, Chengdu University of Technology, Chengdu 610059, Sichuan, People’s Republic of China
Bibliografia
  • 1. Amadei B (1996) Importance of anisotropy when estimating and measuring in situ stresses in rock. Int J Rock Mech Min Sci Geomech Abstr 33(3):293–325
  • 2. Amadei B, Rogers JD, Goodman RE (1983) Elastic constants and tensile strength of anisotropic rocks. In: Proceedings of the 5th international congress of rock mechanics, pp A189–A196
  • 3. Babendererde S, Hoek E, Marinos P, Cardoso AS (2004) Characterization of granite and the underground construction in metro do Porto, Portugal. In: Proceeding of international conference on site characterization, Porto, pp 19–22
  • 4. Barla G (1974) Rock anisotropy: theory and laboratory testing. Rock Mech 114:131–169
  • 5. Barla G (2016) Full-face excavation of large tunnels in difficult conditions. J Rock Mech Geotech Eng 8(3):294–303
  • 6. Cerfontaine B, Collin F (2018) Cyclic and fatigue behavior of rock materials: review, interpretation and research perspectives. Rock Mech Rock Eng 51(2):391–414
  • 7. Cheng JL, Yang SQ, Chen K, Ma D, Li FY, Wang LM (2017) Uniaxial experimental study of the acoustic emission and deformation behavior of composite rock based on 3D digital image correlation (DIC). Acta Mech Sin 33(06):999–1021
  • 8. Cho JW, Kim H, Jeon S, Min KB (2012) Deformation and strength anisotropy of Asan gneiss, Boryeong shale, and Yeoncheon schist. Int J Rock Mech Min Sci 50:158–169
  • 9. Colak K, Unlu T (2004) Effect of transverse anisotropy on the Hoek–Brown strength parameter ‘mi’ for intact rocks. Int J Rock Mech Min Sci 41(6):1045–1052
  • 10. Donath FA (1964) A strength variation and deformational behavior of anisotropic rocks. State of stress in the Earth’s crust. Elsevier, New York, pp 281–298
  • 11. Eberhardt E, Stead D, Stimpson B (1999) Quantifying progressive prepeak brittle fracture damage in rock during uniaxial compression. Int J Rock Mech Min Sci Geomech Abstr 36(3):361–380
  • 12. Gatelier N, Pellet F, Loret B (2002) Mechanical damage of an anisotropic porous rock in cyclic triaxial tests. Int J Rock Mech Min Sci Geomech Abstr 39(3):335–354
  • 13. Gong QM, Jiao YY, Zhao J (2006) Numerical modelling of the effects of joint spacing on rock fragmentation by TBM cutters. Tunn Undergr Space Technol 21(1):46–55
  • 14. Gong WL, Peng YY, Sun XM (2015) Enhancement of low-contrast thermograms for detecting the stressed tunnel in horizontally stratified rocks. Int J Rock Mech Min Sci 74:69–80
  • 15. Gonzaga GG, Leite MH, Corthésy R (2008) Determination of anisotropic deformability parameters from a single standard rock specimen. Int J Rock Mech Min Sci 45(8):1420–1438
  • 16. Han B, Wang ZY, Ding XL, Xu P (2007) Numerical simulation for rheological characteristics of interbedded strata of soft and hard rock. Chin J Yangtze River Sci Res Inst 24(2):25–29 (in Chinese)
  • 17. He MC (2011) Physical modeling of an underground roadway excavation in geologically 45° inclined rock using infrared thermography. Eng Geol 121(3–4):165–176
  • 18. He MC, Xie HP, Peng SP, Jiang YD (2005) Study on rock mechanics in deep mining engineering. Chin J Rock Mech Eng 24(16):2803–2813 (in Chinese)
  • 19. He MC, Gong WL, Li DJ, Zhai HM (2009) Physical modeling of failure process of the excavation in horizontal strata based on IR thermography. Int J Min Sci Technol 19(6):689–698
  • 20. He MC, Gong WL, Zhai HM, Zhang HP (2010) Physical modeling of deep ground excavation in geologically horizontal strata based on infrared thermography. Tunn Undergr Space Technol Inc Trenchless Technol Res 25(4):366–376
  • 21. Jin JF, Li XB, Yin ZQ, Zou Y (2011) A method for defining rock damage variable by wave impedance under cyclic impact loadings. Chin J Rock Soil Mech 32(5):1385–1393+1410
  • 22. Kachanov LM (1958) Time of the rupture process under creep conditions. Izv Akad Nauk SSRO Tech Nauk 8:26–31
  • 23. Khanlari G, Rafiei B, Abdilor Y (2015) Evaluation of strength anisotropy and failure modes of laminated sandstones. Arab J Geosci 8:3089–3102
  • 24. Klimesch DS, Ray AS (1998) Autoclaved cement-quartz pastes with metakaolin additions. Adv Cem Res 7:109–118
  • 25. Kyoya T (1985) A damage mechanics theory for discontinuous rock mass. In: Proceedings of the 5th international conference on numerical methods in geomechanics, Nagoya, 1–5 April, pp 469–480
  • 26. Liu QS, Shi K, Huang X (2013) Feasibility of application of TBM in construction of deep coal mine and its key scientific problems. Chin J Min Saf Eng 30(5):633–641 (in Chinese)
  • 27. Malan DF, Spottiswoode SM (1997) Time-dependent fracture zone behavior and seismicity surrounding deep level stopping operations. Rockburst and seismicity in mines. A. A. Balkema, Rotterdam, pp 173–177
  • 28. Martin CD, Chandler NA (1994) The progressive fracture of Lac du Bonnet granite. Int J Rock Mech Min Sci 31(6):643–659
  • 29. McLamore R, Gray KE (1967) The mechanical behavior of anisotropic sedimentary rocks. J Eng Ind 89:62–73
  • 30. Meng Q, Zhang M, Han L, Pu H, Nie T (2016) Effects of acoustic emission and energy evolution of rock specimens under the uniaxial cyclic loading and unloading compression. Rock Mech Rock Eng 49(10):3873–3886
  • 31. Murakami S (1983) Notion of continuum damage mechanics and its application to anisotropic creep damage theory. J Eng Mater Technol 105(2):99–105
  • 32. Nasseri MH, Rao KS, Ramamurthy T (1997) Failure mechanism in schistose rocks. Int J Rock Mech Min Sci 34(3–4):219
  • 33. Naumann M, Hunsche U, Schulze O (2007) Experimental investigations on anisotropy in dilatancy, failure and creep of Opalinus Clay. Phys Chem Earth 32:889–895
  • 34. Niandou H, Shao JF, Henry JP, Fourmaintraux D (1997) Laboratory investigation of the mechanical behavior of Tournemire shale. Int J Rock Mech Min Sci 34:3–16
  • 35. Nova R (1980) The failure of transversely isotropic rocks in triaxial compression. Int J Rock Mech Min Sci Geomech Abstr 17:325–332
  • 36. Nunes AL (2002) A new method for the determination of transverse isotropic orientation and associated elastic parameters for intact rock. Int J Rock Mech Min Sci 9:257–273
  • 37. Qian XQ, Li ZJ (2001) The relationships between stress and strain for high-performance concrete with metakaolin. Cem Concr Res 31:1607–1611
  • 38. Ramamurthy T (1993) Strength, modulus responses of anisotropic rocks. In: Hudson JA (ed) Compressive rock engineering, vol 1. Pergamon, Oxford, pp 313–329
  • 39. Royer-Carfagni G, Salvatore W (2000) The characterization of marble by cyclic compression loading: experimental results. Mech Cohes Frict Mater 5(7):535–563
  • 40. Sanio HP (1985) Prediction of the performance of disc cutters in anisotropic rock. Int J Rock Mech Min Sci Geomech Abstr Geomech Abstr 22(3):153–161
  • 41. Shang YJ, Yang ZF, Zeng QL, Sun YC, Shi YY, Yuan GX (2007) Retrospective analysis of TBM accidents from its poor flexibility to complicated geological conditions. Chin J Rock Mech Eng 26(12):2404–2411 (in Chinese)
  • 42. Stille H, Palmström A (2008) Ground behaviour and rock mass composition in underground excavations. Tunn Undergr Space Technol 23(1):46–64
  • 43. Tien YM, Kuo MC (2001) A failure criterion for transversely isotropic rocks. Int J Rock Mech Min Sci 38:399–412
  • 44. Tien YM, Tsao PF (2000) Preparation and mechanical properties of artificial transversely isotropic rock. Int J Rock Mech Min Sci 37:1001–1012
  • 45. Tien YM, Kuo MC, Juang CH (2006) An experimental investigation of the failure mechanism of simulated transversely isotropic rocks. Int J Rock Mech Min Sci 43:1163–1181
  • 46. Vogel M, Andrast HP (2000) Alp transit-safety in construction as a challenge: health and safety aspects in very deep tunnel construction. Tunn Undergr Space Technol 15(4):481–484
  • 47. Wang AM, Li XG, Yang CH, Huang ZQ (2010) Study of interaction between creep deformation of bedded salt rock. Chin J Rock Soil Mech 31(12):3965–3970 (in Chinese)
  • 48. Xia CC, Zhong SY (1989) Experimental data processing method in consideration of influence of loading history on rock specimen deformation. J Cent South Inst Min Metall 20(1):18–24 (in Chinese)
  • 49. Xie HP, Gao F, Ju Y (2015) Research and development of rock mechanics in deep ground engineering. Chin J Rock Mech Eng 34(11):2161–2178 (in Chinese)
  • 50. Xu P, Yang SQ (2015) Study of visco-elasto-plastic constitutive model of coal under cyclic loading. Chin J Rock Mech Eng 34(3):537–545 (in Chinese)
  • 51. Yang SQ, Hu B (2018) Creep and long-term permeability of a red sandstone subjected to cyclic loading after thermal treatments. Rock Mech Rock Eng 51:2981–3004
  • 52. Yang SQ, Ranjith PG, Huang YH, Yin PF, Jing HW, Gui YL, Yu QL (2015) Experimental investigation on mechanical damage characteristics of sandstone under triaxial cyclic loading. Geophys J Int 201(2):662–682
  • 53. Yang SQ, Tian WL, Ranjith PG (2017) Experimental investigation on deformation failure characteristics of crystalline marble under triaxial cyclic loading. Rock Mech Rock Eng 50(11):2871–2889
  • 54. Yang SQ, Tian WL, Huang YH (2018) Failure mechanical behavior of pre-holed granite specimens after elevated temperature by particle flow code. Geothermics 72:124–137
  • 55. Zhao YL, Zhang LY, Wang WJ, Wan W, Li SQ, Ma WH, Wang YX (2017) Creep behavior of intact and cracked limestone under multi-level loading and unloading cycles. Rock Mech Rock Eng 50(6):1409–1424
Uwagi
Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2020).
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-130f6c9f-4288-4696-9881-c7024776a79e
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.