Finishing treatment of marine pump shafts made of X5CRNI18-10 steel

• Autorzy: Labuda W.

Identyfikatory

DOI

10.5604/01.3001.0012.2803

• Języki publikacji: EN

Abstrakty

EN

One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the results of influence of cutting parameters change on temperature and cutting forces during turning process of stainless steel. A shaft made of 304L stainless steel was used for the research. The cutting process was carried out on a universal CDS 6250 BX-1000 centre lathe. Measurement of cutting forces during lathing process used DKM 2010 turning dynamometer. The turning process was conducted by a cutting tool with CCET09T302R-MF insert by DIJET. During the turning, the following machining parameters were used: cutting speed Vc = 152, 219, 304 m/min, feed f = 0.044, 0.062, 0.083 mm/rev and cutting depth ap = 0.4, 0.8, 1.2, 1.6 mm. The view of the nose radius of cutting tool before and after the turning process was made by the Smartzoom 5 microscope.

Słowa kluczowe

EN

turning dynamometer; temperature; cutting forces; stainless steel

• Wydawca: Łukasiewicz Research Network - Institute of Aviation ; European Science Society of Powertrain and Transport KONES Poland ; Wydawnictwo Instytutu Technicznego Wojsk Lotniczych
• Czasopismo: Journal of KONES
• Rocznik: 2018
• Tom: Vol. 25, No. 2
• Strony: 215--222
• Opis fizyczny: Bibliogr. 13 poz., rys.

Twórcy

autor

Labuda W.

• Gdynia Maritime University, Faculty of Marine Engineering Morska Street 83, 81-225 Gdynia, Poland tel.: [phone], fax: [phone]

Bibliografia

• [1] Agustina, B., Bernal, C., Camacho, A. M., Rubio, E. M., Experimental analysis of the cutting forces obtained in dry turning processes of UNS A97075 aluminium alloys, The Manufacturing Engineering Society International Conference, MESIC, Procedia Engineering 63, pp. 694-699, 2013.
• [2] Bensouilah,H., Aouici, H., Meddour,I., Yallese,M. A., Mabrouki,T., Girardin, F., Performance of coated and uncoated mixed ceramic tools in hard turning process, Measurement, Elsevier, 2015.
• [3] Callister Jr., W. D., Materials science and engineering an introduction, John Wiley & Sons, Inc. USA 2007.
• [4] Dudzik, K., The influence of welding parameters on the quality of joints made by FSW of AW5083 aluminium alloy, In METAL 2016: 25th Anniversary International Conference on Metallurgy and Materials. Ostrava: TANGER, pp. 694-699, 2016.
• [5] Dyl, T., Starosta, R., Określenie wpływu geometrii i rodzaju materiału płytek skrawających na topografię toczonych powłok kompozytowych, Inżynieria Materiałowa, Nr 6, pp. 701-704, 2012.
• [6] Dyl, T., Starosta, R., Wpływ geometrii i gatunku płytek skrawających na strukturę geometryczną toczonych powłok stopowych, Inżynieria Materiałowa, Nr 4, pp. 395-398, 2011.
• [7] Labuda, W., Khudoley, A., The influence of burnishing process on surface roughness of stainless steel researched by optical profiler, In METAL 2016: 25th Anniversary International Conference on Metallurgy and Materials. Ostrava: TANGER, pp. 765-770, 2016.
• [8] Labuda, W., The influence of changing the side angle of the cutting tool by Wiper technology on the value of material ratio parameters of steel applied to marine pump shaft pins, Journal of KONES Powertrains and Transport, Vol. 22, No. 2, pp. 139-147, Warsaw 2015.
• [9] Labuda, W., The influence of cutting inserts geometric on surface roughness of steel applied to sea water pump shafts, Journal of KONES Powertrains and Transport, Vol. 22, No. 3, pp. 133-140, Warsaw 2015.
• [10] Labuda, W., The analysis of cutting tool geometric on cutting forces and surface roughness of steel applied to marine pumps shaft pins, Journal of KONES Powertrains and Transport, Vol. 21, No. 1, pp. 147-152, Warsaw 2014.
• [11] Magri, A., Diniz, A. E., Suyama, D. I., Evaluating the use of high-pressure coolant in turning process of Inconel 625 nickel-based alloy, Proceedings of the Institution of Mechanical Engineers Part B-Journal of Engineering Manufacture, Vol. 232, pp. 1182-1192, 2018.
• [12] Sadilek, M., Dubsky, J., Sadilkova, Z., Poruba, Z., Cutting forces during turning with variable depth of cut, Perspectives in Science, Elsevier, 2015.
• [13] Starosta, R., Dyl, T., Obróbka wykańczająca natryskiwanych płomieniowo powłok Ni-Al, ocena zużycia borazonowych płytek skrawających, Tribologia. Teoria i Praktyka, Nr 4, pp. 245-252, 2011.

Uwagi

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).