Experimental and Thermodynamic Study of Selected in-Situ Composites from the Fe-Cr-Ni-Mo-C System

• Autorzy: Wieczerzak K. , Bala P. , Dziurka R. , Stepien M. , Tokarski T. , Cios G. , Gorecki K.

Identyfikatory

DOI

10.1515/amm-2016-0205

• Języki publikacji: EN

Abstrakty

EN

The aim of the study was to synthesize and characterize the selected in-situ composites from the Fe-Cr-Ni-Mo-C system, additionally strengthened by intermetallic compounds. The project of the alloys was supported by thermodynamic simulations using Calculation of Phase Diagram approach via Thermo-Calc. Selected alloys were synthesized in an arc furnace in a high purity argon atmosphere using a suction casting unit. The studies involved a range of experimental techniques to characterize the alloys in the as-cast state, including optical emission spectrometry, light microscopy, scanning electron microscopy, electron microprobe analysis, X-ray diffraction and microhardness tests. These experimental studies were compared with the Thermo-Calc data and high resolution dilatometry. The results of investigations presented in this paper showed that there is a possibility to introduce intermetallic compounds, such as χ and σ, through modification of the chemical composition of the alloy with respect to Nieq and Creq. It was found that the place of intermetallic compounds precipitation strongly depends on matrix nature. Results presented in this paper may be successfully used to build a systematic knowledge about the group of alloys with a high volume fraction of complex carbides, and high physicochemical properties, additionally strengthened by intermetallic compounds.

Słowa kluczowe

EN

Fe-Cr-Ni-Mo-C; in-situ composites; intermetallic compounds; dilatometry; microstructure

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2016
• Tom: Vol. 61, iss. 2B
• Strony: 1241--1247
• Opis fizyczny: Bibliogr. 28 poz., rys., tab., wykr.

Twórcy

autor

Wieczerzak K.

• AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Al. A. Mickiewicza 30, 30-059 Krakow, Poland

autor

Bala P.

• AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Al. A. Mickiewicza 30, 30-059 Krakow, Poland

autor

Dziurka R.

• AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Al. A. Mickiewicza 30, 30-059 Krakow, Poland

autor

Stepien M.

• AGH University of Science and Technology, Academic Centre for Materials and Nanotechnology, Al. A. Mickiewicza 30, 30-059 Krakow, Poland

autor

Tokarski T.

• AGH University of Science and Technology, Academic Centre for Materials and Nanotechnology, Al. A. Mickiewicza 30, 30-059 Krakow, Poland

autor

Cios G.

• AGH University of Science and Technology, Academic Centre for Materials and Nanotechnology, Al. A. Mickiewicza 30, 30-059 Krakow, Poland

autor

Gorecki K.

• AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Al. A. Mickiewicza 30, 30-059 Krakow, Poland

Bibliografia

• [1] S. Tjong, Mater. Sci. Eng. R Reports. 29, 49-113 (2000).
• [2] A. I. Filho, W. da S. Cardoso, L. C. Gontijo, R. V. da Silva, L. C. Casteletti, Metall. Mater. 66, 467-471 (2013).
• [3] J. O. Nilsson, A. Wilson, Mater. Sci. Technol. 9, 545-554 (1993).
• [4] M. Pohl, O. Storz, T. Glogowski, Mater. Charact. 58, 65-71 (2007).
• [5] K. Chan, S. Tjong, Materials (Basel). 7, 5268-5304 (2014).
• [6] G. Fargas, M. Anglada, A. Mateo, J. Mater. Process. Technol. 209, 1770-1782 (2009).
• [7] S.-H. Kim, H. Kim, N. J. Kim, Nature. 518, 77-79 (2015).
• [8] K. Suganuma, H. Kayano, S. Yajima, J. Mater. Sci. 16, 3131-3140 (1981).
• [9] X.-C. Lu, S. Li, X. Jiang, Wear. 251, 1234-1238 (2001).
• [10] Y. Q. Wang, J. Han, H. C. Wu, B. Yang, X. T. Wang, Nucl. Eng. Des. 259, 1-7 (2013).
• [11] G. Fargas, A. Mestra, A. Mateo, Wear. 303, 584-590 (2013).
• [12] T. Koziel, Arch. Metall. Mater. 60, 765-771 (2015).
• [13] A. L. Shaeffler, Met. Prog. 56, 680 (1949).
• [14] J. O. Andersson, T. Helander, L. Höglund, P. F. Shi, B. Sundman, Calphad. 26, 273-312 (2002).
• [15] K. Wieczerzak, P. Bala, M. Stepien, G. Cios, T. Koziel, JMADE. 94, 61-68 (2016).
• [16] K. Wieczerzak, P. Bała, M. Stępień, G. Cios, T. Kozieł, Arch. Metall. Mater. 60, 769-782 (2015).
• [17] H. J. Goldschmidt, Interstitial alloys, 1967 Springer Science+Business Media, LLC, New York.
• [18] M. Palcut, M. Vach, R. Cicka, J. Janovec, Arch. Metall. Mater. 53, 1157-1164 (2008).
• [19] C. P. Tabrett, I. R. Sare, M. R. Ghomashchi, Int. Mater. Rev. 41, 59-82 (1996).
• [20] B. Weiss, R. Stickler, Metall. Trans. 3, 851-866 (1972).
• [21] D. M. Escriba, E. Materna-Morris, R. L. Plaut, A. F. Padilha, Mater. Charact. 60, 1214-1219 (2009).
• [22] J. Michalska, M. Sozańska, Mater. Charact. 56, 355-362 (2006).
• [23] S. K. Ghosh, S. Mondal, Mater. Charact. 59, 1776-1783 (2008). doi:10.1016/j.matchar.2008.04.008.
• [24] R. D. Campbell, Key Eng. Mater. 69-70, 167-216 (1992).
• [25] M. A. Streicher, Corrosion. 30, 115-124 (1974).
• [26] M. J. Cieslak, A. M. Ritter, W. F. Savage, Weld. J. 63, 133-140 (1984).
• [27] N. Llorca-Isern, H. López-Luque, I. López-Jiménez, M. V. Biezma, Mater. Charact. 112, 20-29 (2016).
• [28] A. Inoue, T. Masumoto, Metall. Trans. A. 11, 739-747 (1980).

Uwagi

PL

Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę