Identyfikatory
Warianty tytułu
Języki publikacji
Abstrakty
Austenitic stainless steels are materials, that are widely used in various fields of industry, architecture and biomedicine. Their specific composition of alloying elements has got influence on their deformation behavior. The main goal of this study was evaluation of magnetic properties of selected steels, caused by plastic deformation. The samples were heat treated in different intervals of temperature before measuring. Then the magnetic properties were measured on device designed for measuring of magnetism. From tested specimens, only AISI 304 confirmed effect of plastic deformation on the magnetic properties. Magnetic properties changed with increasing temperature.
Czasopismo
Rocznik
Tom
Strony
15--18
Opis fizyczny
Bibliogr. 12 poz., rys., tab.
Twórcy
autor
- Department of Material Engineering, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovak Republic
autor
- Department of Material Engineering, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovak Republic
autor
- Department of Physics, Faculty of Electrical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovak Republic
Bibliografia
- 1. CORREA SOARES G. et al. 2017. Strain hardening behavior and microstructural evolution during plastic deformation of dual phase, non-grain oriented electrical and AISI 304 steels, Materials Science and Engineering A 684, 577-585.
- 2. GAUZZI F. ET AL. 2006. AISI 304 steel: anomalous evolution of martensitic phase following heat treatments at 400 °C, Materials Science and Engineering A 438-440, 202-206.
- 3. JAKOBSEN P.T., MAAHN E. 2001. Temperature and potential dependence of crevice corrosion of AISI 316 steel, Corrosion Science 43, 1693-1709.
- 4. MARTÍNKOVÁ J. 2010.Vliv delta feritu na mechanické vlastnosti ocelí a metody stanovení jeho obsahu (Effect of delta ferrite on mechanical properties of steels and methods of determining of its content), SVOČ-FST, Západočeská univerzita v Plzni, Fakulta strojní.
- 5. MITRA A. ET AL. 2006: Effect of plastic deformation on the magnetic properties 304 stainless steel during tensile loading, ECNDT, We.4.2.4.
- 6. NOVÝ F. ET AL. 2014. Fatigue strength improvement of the AISI 316Ti austenitic stainless steel by shot peening, Production Engineering Archives Vol. 4, No. 3, 2-6.
- 7. O'SULLIVAN D. ET AL. 2004. Characterisation of ferritic stainless steel by Barkhausen techniques, NDT & E Inetrnational, Vol. 37, 489-496.
- 8. RODRÍGUEZ-MARTÍNEZ J.A. ET AL. 2011. Experimental study on the martensitic transformation in AISI 304 steel sheets subjected to tension under wide ranges of strain rate at room temperature, Materials Science and Engineering A 528, 5974-5982.
- 9. TOURKI Z. ET AL. 2005. The kinetic of induced martensitic formation and its effect on forming limit curves in the AISI 304 stainless steel, Journal of materials processing technology 166, 330-336.
- 10. VÉRTESy G. ET AL. 2005. Nondestructive indication of plastic deformation of cold-rolled stainless steel by magnetic minor hysteresis loop measurement, Journal of Magnetism and Magnetic Materials 285, 335-342.
- 11. YAE KINA A. ET AL. 2008. Microstructure and intergranular corrosion resistance evaluation of AISI 304 steel for high temperature service, Materials characterisation 59, 651-655.
- 12. YAMASAKI T. ET AL. 1996, Effect of applied stresses on magneto-striction of low carbon steel, NDT & E International, Vol. 29, No.5, pp. 263-268.
Uwagi
Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę (zadania 2017).
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-1092b64e-4716-4467-9c43-9ccbb4fdb791
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.