Proposal of a piston engine with close thermal cycle of working medium

• Autorzy: Mitianiec W.
• Języki publikacji: EN

Abstrakty

EN

Ecological aspects and utilization of biomass as a fuel leads to applying of a closed work cycle in the piston engine. It forces usually to delivering of heat to working medium through a heat exchanger. The heat may get from any type of fuel in an external combustion chamber, which allows on precisely control of combustion process. The paper describes a new conception of the engine operating in two-stroke cycle with working medium being in the close system, the best with the perfect gas as argon or helium. The delivering process of working medium with high temperature from the heat exchanger takes place through the inlet valve during a few dozen degrees of CA rotation in piston position at TDC. Expansion stroke takes place until outlet valve opens shortly BBDC. The outlet period from the cylinder follows almost at constant pressure and at low temperature to an adiabatic chamber, from where the working medium is compressed by an adiabatic compressor to pressure near pressure being in the heat exchanger. The engine works in two-stroke cycle and enables to get low temperature and pressure as early as BDC through a long time of opening of the outlet valve. The paper presents the ideological scheme of the engine system and theoretical thermal cycle. On this basis one presents the theoretical description of the individual thermodynamic processes with determination of thermal parameters of the characteristic points of the cycle. This article determines also the thermal efficiency of such closed cycle. The presented engine may have a practical applying as a stationary engine in energetic systems, where as fuel may be biomass, which globally influences on decreasing of CO2 and NOx by temperature control of the combustion process

Słowa kluczowe

EN

transport; combustion engine; thermal cycles; closed system

• Wydawca: Łukasiewicz Research Network - Institute of Aviation ; European Science Society of Powertrain and Transport KONES Poland ; Wydawnictwo Instytutu Technicznego Wojsk Lotniczych
• Czasopismo: Journal of KONES
• Rocznik: 2013
• Tom: Vol. 20, No. 1
• Strony: 209--217
• Opis fizyczny: Bibliogr. 14 poz., rys.

Twórcy

autor

Mitianiec W.

• Cracow University of Technology Jana Pawla II Av. 37, 31-864 Krakow, Poland tel: [phone]; Fax: [phone]

Bibliografia

• [1] Blair, P. G., Design and simulation of two-stroke engines, SAE, 1996.
• [2] Dry, M.E., Catalytic aspects of industrial Fischer-Tropsch synthesis, Journal of Molecular Catalysis, 17, 133-144, 1982.
• [3] Fraidl, G., Herzog P., Multiple benefit technology development for gasoline-diesel-hybrid powertrains, Combustion Engines 1/2007(128), PTNSS-2007-SS1-202, Bielsko-Biała 2007.
• [4] Guzella, L., Onder, C. H., Introduction to modeling and control of internal combustion engine systems, Springer-Verlag, Berlin 2010.
• [5] Heywood, J. B., Internal Combustion Engine. Fundamentals, McGraw-Hill, New York 1988.
• [6] Kowalewicz, A., Wybrane zagadnienia samochodowych silników spalinowych, Wy􀄪sza Szkoła Inżynierska w Radomiu, Radom 1996.
• [7] Kropiwnicki, J., Comparison of energy efficiency of vehicles powered by different fuels, Combustion Engines 3/2012(150), PTNSS-2012-SS3-304, Bielsko-Biała 2012.
• [8] Look, D. C., Sauer, H. J., Engineering Thermodynamics PWS Engineering, Boston 1986.
• [9] Niewczas, A., Gil, L., Ignaciuk, P., Chosen aspects of biofuel usage on the example of Amelina oil metyl ester, Combustion Engines 1/2012(148), PTNSS-2012-SS1-112, Bielsko- Biała 2012.
• [10] Ragland, K., Bryden, K., Combustion Engineering, CRC Press Taylor & Francis Group, Boca Raton, FL, USA 2011.
• [11] Rajewski, A., Plains End Power Station-gas reciprocating engines in a grid-stability power plant, Combustion Engines 2/2010 (141), PTNSS-2010-SS2-202, Bielsko-Biała 2010.
• [12] Szargut, J., Termodynamika, PWN, Warszawa 1975.
• [13] Szumanowski, A., Hybrid electric vehicle drives fitted with combustion engines, Combustion Engines 1/2009(136), PTNSS-2009-SS1-102, Bielsko-Biała 2009.
• [14] Żmudzki, S., Silniki Sterlinga, WNT Warszawa 1993.