Utilization of textile denim sludge waste in high load-bearing structural applications

• Autorzy: Beg Tahreem , Siddiqui Muhammad Owais Raza , Butto Muhammad Aslam , Iqbal Kashif , Sun Danmei

Identyfikatory

DOI

10.14314/polimery.2022.7.2

Warianty tytułu

PL

Wykorzystanie odpadów szlamowych z dżinsu tekstylnego w zastosowaniach konstrukcyjnych o dużej nośności

• Języki publikacji: EN

Abstrakty

EN

The paper presents the results of research on the utilization of textile denim sludge waste, which was used to obtain concrete and mortar. For this purpose, cement and sand were replaced with the powdered sludge in the amount of 5 and 10 wt. The sludge was initially analyzed by FTIR and XRD to identify functional groups and chemical composition, respectively. Replacing sand with sludge resulted in a significant reduction in the concrete compressive and flexural strength (> 50%). Significantly better results were obtained by replacing cement with 5 wt% of sludge. In this case, the concrete compressive strength decreased by only 14%, and the flexural strength by 15%.

PL

W pracy przedstawiono wyniki badań dotyczące utylizacji odpadów szlamowych z dżinsu tekstylnego, których użyto do otrzymywania betonu i zaprawy murarskiej. W tym celu cement i piasek zastąpiono sproszkowanym szlamem w ilości odpowiednio 5 i 15% mas. Osad poddano wstępnej analizie za pomocą FTIR i XRD w celu zidentyfikowania odpowiednio grup funkcyjnych i składu chemicznego osadu. Zastąpienie piasku szlamem spowodowało znaczne zmniejszenie wytrzymałości betonu na ściskanie i zginanie (> 50%). Znacznie lepsze wyniki uzyskano zastepując cement szlamem. W tym przypadku wytrzymałość betonu na ściskanie zmniejszyła się tylko o 14%, a wytrzymałość na zginanie o 15%.

Słowa kluczowe

EN

textile composite; textile effluent sludge; concrete; mortar

PL

kompozyt tekstylny; tekstylny osad ściekowy; beton; zaprawa

• Wydawca: Sieć Badawcza Łukasiewicz – Instytut Chemii Przemysłowej
• Czasopismo: Polimery
• Rocznik: 2022
• Tom: Vol. 67, nr 7-8
• Strony: 298--307
• Opis fizyczny: Bibliogr. 36 poz., rys., tab.

Twórcy

autor

Beg Tahreem

• Department of Textile Engineering , NED University of Engineering & Technology, University Road, 75270, Karachi, Pakistan

• https://orcid.org/0000-0002-7622-5105

autor

Siddiqui Muhammad Owais Raza

• Department of Textile Engineering , NED University of Engineering & Technology, University Road, 75270, Karachi, Pakistan
• School of Textiles & Design, Heriot-Watt University, TD1 3HF, Galashiels, UK

• https://orcid.org/0000-0002-4687-2125

autor

Butto Muhammad Aslam

• Department of Civil Engineering, NED University of Engineering & Technology, University Road, 75270, Karachi, Pakistan

• https://orcid.org/0000-0002-3422-4059

autor

Iqbal Kashif

• Department of Textile Engineering, National Textile University, Sheikhupura Road, 37610, Faisalabad, Pakistan

• https://orcid.org/0000-0002-3404-2562

autor

Sun Danmei

• School of Textiles & Design, Heriot-Watt University, TD1 3HF, Galashiels, UK

• https://orcid.org/0000-0003-3213-5615

Bibliografia

• [1] Memon D.A.: Pakistan Texts Journal 2014, 40-42.
• [2] https://www.tco.com.pk/documents/7098418c64.pdf (access date 18.02.2022).
• [3] https://profit.pakistantoday.com.pk/2021/11/28/profit-e-magazine-issue-169/ (access date 18.02.2022).
• [4] https://www.linkedin.com/pulse/pakistan-has-become-denim-hub-a-rauf-razzak-ganatra (access date 18.02.2022).
• [5] https://www.southasiainvestor.com/2021/10/pakistans-denim-exports-to-us-soared-62.html (access date 19.02.2022).
• [6] https://www.trade.gov/pakistan-country-commercial-guide (access date 22.03.2022).
• [7] https://apparelinsider.com/pakistani-denim-business-makes-wastewater-breakthrough/ (access date 22.03.2022).
• [8] Ayşegül K.: “Waste in Textile and Leather Sectors”, Intechopen Limited, London. 2020, chapter 3.
• [9] Guerra-Rodríguez S., Oulego P., Rodríguez E. et al.: Water 2020, 12(5), 1. https://doi.org/10.3390/w12051431
• [10] Mayer A., Haas W., Wiedenhofer D. et al.: Journal of Industrial Ecology 2018, 23(1), 62. https://doi.org/10.1111/jiec.12809
• [11] Salmenperä H., Pitkänen K., Kautto P., Saikku L..: Journal of Cleaner Production 2021, 280, 1. https://doi.org/10.1016/j.jclepro.2020.124339
• [12] George T. H.: “Wastewater engineering : treatment and resource recovery”, McGraw Hill. USA 2014, p. 1–10.
• [13] Cieślik B Journal of Cleaner Production 2017, 142, 1728. https://doi.org/10.1016/j.jclepro.2016.11.116
• [14] Lynn C.J., Dhir R.K., Ghataora G.S.: Water Science and Technology 2016, 74(1), 17. https://doi.org/10.2166/wst.2016.040
• [15] Rezaee F., Danesh S., Tavakkolizadeh M., Mohammadi-Khatami M.: Journal of Cleaner Production 2019, 214, 749. https://doi.org/10.1016/j.jclepro.2018.12.153
• [16] Savija B.: Materials 2018, 11(5), 1. https://doi.org/10.3390/ma11050654
• [17] Sadowski T., Golewski G.L.: Composite Structures 2018, 183, 527. https://doi.org/10.1016/j.compstruct.2017.05.073
• [18] Srivastava V.K., Shembekar P.S., Prakash R.: Composite Structures 1988, 10(4), 271. https://doi.org/10.1016/0263-8223(88)90006-2
• [19] Choi J.I., Song K.I., Song J.K., Lee B.Y.: Composite Structures 2016, 138, 116. https://doi.org/10.1016/j.compstruct.2015.11.046
• [20] Kim H.K., Nam I.W., Lee H.K.: Composite Structures 2014, 107, 60. https://doi.org/10.1016/j.compstruct.2013.07.042
• [21] Correia S.L., Partala T., Loch F.C., Segadães A.M.: Composite Structures 2010, 92(9), 2047. https://doi.org/10.1016/j.compstruct.2009.11.007
• [22] Xie T., Visintin P.: Journal of Cleaner Production 2018, 203, 68. https://doi.org/10.1016/j.jclepro.2018.08.254
• [23] Niewiadomski P., Hoła J., Ćwirzeń A.: Archives of Civil and Mechanical Engineering 2018, 18(3), 877.
• [24] Mohammed B.S., Adamu M.: Construction and Building Materials 2018, 159, 234. https://doi.org/10.1016/j.conbuildmat.2017.10.098
• [25] Benlalla M., Elmoussaouiti M., Dahhou M.: Applied Clay Science 2015, 118, 171. https://doi.org/10.1016/j.clay.2015.09.012
• [26] Amminudin A.L., Ramadhansyah P.J., Doh S.I.: Materials Science and Engineering 2020, 712(1), 1.
• [27] Qudoos A., Jeon I.K., Kim S.S. et al.: Materials 2020, 13(1), 1. https://doi.org/10.3390/ma13010251
• [28] Rabie G.M., Abd El-Halim H., Rozaik E.: Ain Shams Engineering Journal 2019, 10(4), 705. https://doi.org/10.1016/j.asej.2019.07.008
• [29] Li D., Zhuge Y., Liu Y. et al.: Construction and Building Materials 2021, 277, 1. https://doi.org/10.1016/j.conbuildmat.2021.122330
• [30] Shathika S.B., Gandhimathi R., Ramesh S.T., Nidheesh P.V.: Journal of Material Cycles and Waste Management 2013, 15(4), 564. https://doi.org/10.1007/s10163-013-0139-4
• [31] Balasubramanian J., Sabumon P.C., Lazar J.U., Ilangovan R.: Waste Management 2006, 26(1), 22. https://doi.org/10.1016/j.wasman.2005.01.011
• [32] Chen C., Wu H.: Environmental Technology 2018, 39(11), 1359. https://doi.org/10.1080/09593330.2017.1329353
• [33] Rahman A., Urabe T., Kishimoto N., Mizuhara S.: Environmental Technology 2015, 36(19), 2443. https://doi.org/10.1080/09593330.2015.1034188
• [34] Arul N., Senthilkumar S., Velumani P.: International Journal of Applied Engineering Research 2017, 10(38), 28182.
• [35] Rahman A., Urabe T., Kishimoto N., Mizuhara S.: Construction and Building Materials 2017, 138, 326. https://doi.org/10.1016/j.conbuildmat.2017.02.017
• [36] Reis G.S., Cazacliu B.G., Cothenet A. et al.: Journal of Cleaner Production 2020, 258, 1. https://doi.org/10.1016/j.jclepro.2020.120733

Uwagi

Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023).