Structural and mechanical properties of laboratory rolled steels high-alloyed with manganese and aluminium

• Autorzy: Kuc D. , Hadasik E. , Niewielski G. , Schindler I. , Mazancova E. , Rusz S. , Kawulok P.
• Języki publikacji: EN

Abstrakty

EN

The paper deals with rolling conditions, microstructure, as well as basic mechanical properties of four different high manganese steels after laboratory melting, casting, and hot and cold rolling. The stacking fault energy of heats was in the interval of 85–114 mJ m−2 thanks to the high aluminium contents. The heats with the lowest sum of (C+Mn) supported the highest ferrite volume fraction (up to 45%), while the highest sum of (C+Mn) led to 10% ferrite formation. With lower Al/(C+Mn) ratio and lower ferrite fraction higher rolling forces were necessary to be used. Due to heterogeneities of matrixes and observed aluminium oxide complexes differences in mechanical properties were detected. The best results showed the heat with 0.65% C−29.5% Mn−9.0% Al and a stacking fault energy 114 mJ m−2.

Słowa kluczowe

EN

high-manganese steel; stacking fault energy; hot rolling; microstructure; mechanical properties

PL

walcowanie na gorąco; mikrostruktury; właściwości mechaniczne

• Wydawca: Springer ; Wrocław University of Science and Technology
• Czasopismo: Archives of Civil and Mechanical Engineering
• Rocznik: 2012
• Tom: Vol. 12, no. 3
• Strony: 312--317
• Opis fizyczny: Bibliogr. 13 poz., rys., tab., wykr.

Twórcy

autor

Kuc D.

• Silesian University of Technology, Krasińskiego 8, 40-019 Katowice, Poland

autor

Hadasik E.

• Silesian University of Technology, Krasińskiego 8, 40-019 Katowice, Poland

autor

Niewielski G.

• Silesian University of Technology, Krasińskiego 8, 40-019 Katowice, Poland

autor

Schindler I.

• Faculty of Metallurgy and Materials Engineering, VSB – Technical University of Ostrava, 17. listopadu 15/2172, 70833 Ostrava–Poruba, CzechRepublic

autor

Mazancova E.

• Faculty of Metallurgy and Materials Engineering, VSB – Technical University of Ostrava, 17. listopadu 15/2172, 70833 Ostrava–Poruba, CzechRepublic

autor

Rusz S.

• Faculty of Metallurgy and Materials Engineering, VSB – Technical University of Ostrava, 17. listopadu 15/2172, 70833 Ostrava–Poruba, CzechRepublic

autor

Kawulok P.

• Faculty of Metallurgy and Materials Engineering, VSB – Technical University of Ostrava, 17. listopadu 15/2172, 70833 Ostrava–Poruba, CzechRepublic

Bibliografia

• [1] Ju.D. Tjapkin, E.I. Malienko, I.V. Gongadze, I.S. Kalashnikov, I.V. Komarov, Steel coalescence of fragmental regular structure in Fe–Mn–Al–C alloy, Fizika metallov i metallovedenie 68 (3) (1989) 540–547 (in Russian).
• [2] E. Mazancova, K. Mazanec, The stacking fault energy evaluation of the TWIP and TRIPLEX alloys, Metallic Materials 47 (2009) 353–358.
• [3] G. Frommeyer, U. Brux, Microstructures and mechanical properties of high-strength Fe–Mn–Al–C, Steel Research International 77 (9–10) (2006) 627–633.
• [4] http://www.fmmi.vsb.cz/model/
• [5] G.B. Olson, M. Cohen, General mechanism of martensitic nucleation: part I. General concepts and the FCC NuP transformation, Metallurgical and Materials Transactions A 7 (1976) 1897–1904.
• [6] K.Sato,M.Ichinose,Y.Hirotsu, Effects of deformation induced phase transformation and twinning on the mechanical properties of austenite Fe–Mn–Al alloys, ISIJ International 29 (1989) 868–877.
• [7] E. Mazancova, I. Schindler, P. Kozelský, M. Cagala, Hot and cold rolled high alloy Fe–Mn–Al–C, The Metallurgical Journal 62 (4) (2009) 42–45.
• [8] E. Mazancova,I.Schindler,P.Kozelský, M. Cagala, Some problems connected with hot and cold rolled high manganese Fe24Mn1.2C12Al alloy, Acta Metallurgica Slovaca 1 (2010) 212–217.
• [9] K. Ishida, H. Ohtani, N. Satoh, R. Kainuma, T. Nishizawa, Phase equilibria in Fe–Mn–Al–C alloys, ISIJ International 30 (8) (1990) 680–686.
• [10] W.K. Choo, K.H. Han, Phase constitution and lattice parameter relationship in rapidly solidified (Fe0.65Mn0.35)0.83Alx0.17CandFe3AlxC pseudo-binary alloys, Metallurgical and Materials Transactions A 16A (1985) 5–10.
• [11] C.M. Chimani, K. Morwald, Micromechnical investigation of the hot ductility behaviour of steel, ISIJ International 39 (1999) 1194–1199.
• [12] H. Dyja, M. Knapinski, M. Kwapisz, J. Snopek, Physical simulation of controlled rolling and accelerated cooling for ultrafine-grained steel plates, Archives of Metallurgy and Materials 56 (2) (2011) 447–454.
• [13] G.A. Thomas, J.G. Speer, D.K. Matlock, Quenched and partitioned microstructures produced via gleeble simulations of hot-strip mill cooling practices, Metallurgical and Materials Transactions A Physical Metallurgy and Materials Science 42A (12) (2011) 3652–3659.